Specifications

ManualsBrandsBriggs & Stratton ManualsPortable Generator30230

WHAT EVERY ICE RESURFACER SHOULD BE

Welcome to the OLYMPIA™ Advantage

The entire OLYMPIA™ Product line is designed and built to exacting standard to provide trouble free performance. Like

all mechanical equipment however, trouble free performance requires a complete maintenance and proper operating

procedures to be followed. Failure to follow a complete and on-going maintenance program will invalidate the Resurfice

Corp. warranty on the OLYMPIA™ Battery Edger.

Purchaser: .......................................................................................................................................................................

Address: .......................................................................................................................................................................

.......................................................................................................................................................................

Model: .......................................................................................................................................................................

Serial Number: .......................................................................................................................................................................

Date Delivered: .......................................................................................................................................................................

The illustrations and product information contained in this manual were current at the time of publication. In order to

continue Resurfice Corp.'s development of its technology, Resurfice Corp. reserves the right to change designs, models and

specifications without notice and without liability for such changes.

Resurfice Corp. warrants the components of your OLYMPIA™ Battery Edger against defects in material and workmanship,

for two full years from the date of delivery.

The motor for your OLYMPIA™ Battery Edger is a Briggs & Stratton Etek™. To validate it's warranty it must be placed on an

ongoing maintenance program as outlined in the motor manual included with the OLYMPIA™ Battery Edger. The charger is a

Guest

Smart Charger 2621. For the continued safe, economic operation and to validate the Resurfice Corp. warranty, the over

all maintenance and operation of your OLYMPIA™ Battery Edger must strictly follow the guideline outlined in this manual.

Resurfice Corp. or an authorized dealer must first authorize all warranty repairs.

No warranty on this machine will be honored by Resurfice Corp. other than that stated above.

OLYMPIA™

Battery

Edger

WARRAnTY

Summary of content (16 pages)

PAGE 1
OLYMPIA™ Battery Edger W arra n ty Welcome to the OLYMPIA™ Advantage The entire OLYMPIA™ Product line is designed and built to exacting standard to provide trouble free performance. Like all mechanical equipment however, trouble free performance requires a complete maintenance and proper operating procedures to be followed. Failure to follow a complete and on-going maintenance program will invalidate the Resurfice Corp. warranty on the OLYMPIA™ Battery Edger. Purchaser: ...................................
PAGE 2
T able of C o n te n ts For Safe Operation The OLYMPIA™ Battery Edger is intended for use, only by people who have a basic knowledge of motorized equipment operation and maintenance. Resurfice Corp. cannot accept responsibility for any accidents that occur as a result of operation or maintenance of the machine . Operating conditions vary widely and Resurfice Corp.
PAGE 3
1 Delivery Parts Check D elivery P rocedure The OLYMPIA™ Battery Edger is delivered fully assembled along with the Guest® Model 2621 3 Output, 3 Stage battery charger. Upon receipt of the OLYMPIA™ Battery Edger, install the charger in an open area, adjacent to a direct electric power source outlet, according to the Guest installation instructions for battery chargers. Safety Note: Make sure the charger is mounted in an open area, with the fins vertical to maximize venting of the internal heat.
PAGE 4
GUEST® 2621 Installation In order to optomize the performance and useful life of your charger, the following guideline for installation should be followed. 1. Chargers are electronic products designed for efficient energy conversion, specifically taking unregulated AC line power and converting it to an isolated low voltage DC power source. The nature of the process dictates that some heat is generated in the process, and consideration should be given to the proper dissipation of this heat.
PAGE 5
2 Battery Charging Proceedure operati n g P rocedure The OLYMPIA™ Battery Edger is re-charged by a Guest® Model 2621 "smart" charger. It first evaluates the amount of charge in each of the three batteries on the OLYMPIA™ Battery Edger. One of the batteries is charged at a rate of 10 amps and the other two are charged at a rate of 5 amps. Consequently one battery will charge faster then the other two.
PAGE 6
2 Battery Cycles operati n g P rocedure The sealed lead acid gel batteris on the OLYMPIA™ Battery Edger are rated for 1,600 cycles. Every time the OLYMPIA™ Battery Edger is plugged into the GUEST charger constitutes a single cycle. A full charge on the batteries provides for approximately 40 to 60 minutes of operating time, depending on how deep a cut you are making. If you edge the ice surface once a day, it should only take 15 minutes to complete the edging procedure.
PAGE 7
. On the eight blade plate, we recommend every second blade be inset by moving it to the back of the slide groove. The alternate blade tips are positioned correctly by measuring from the outer edge of the blade guard casing to the tip of the blade. It should be 1/16" to 1/8" inside the edge. When the blades are inspected and replaced if necessary, re-attach the blade plate with the four bolts making sure to tighten to a maximum 11 ft. lbs. of torque on the grade 8 bolts.
PAGE 8
2 operati n g P rocedure SAFETY NOTE: NEVER move the OLYMPIA™ Battery Edger backward when the blades are moving or try to cut backwards. 7. When you have completed a full circuit around the ice, raise the cutter assembly to the full up position, release the start bar and turn off the key. Exit the ice surface and store the OLYMPIA™ Battery Edger in the proper storage area next to the charger. SAFETY NOTE: Always release the safety bar before turning the ignition key off.
PAGE 9
IMPORTANT Adhere to the following personal safety precautions when installing or working with the chargers. CHARGER SAFETY 1. Someone should be within voice range or close enough to come to your aid when you work near a seal leadINSTRUCTIONS acid Gel battery. 2. Have plenty of fresh water and soap nearby in case battery acid contacts your skin, clothing or eyes. 3. Wear complete eye protection and clothing protection. Avoid touching your eyes while working near a battery. 4.
PAGE 10
3 PARTS LIST Control Arm Ref.
PAGE 11
Handel Bar Ref.
PAGE 12
3 PARTS LIST Panels & Sled Ref.
PAGE 13
Under Carriage Ref.
PAGE 14
3 PARTS LIST Battery Tray Ref.# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 12 Part # 49-33500 49-36250 55-25095 55-25000 55-25045 49-30110 55-25055 55-25050 49-33115 55-25100 49-30550 49-38290 37- 198 49-30150 49-33200 Description Locknut - Nylon 3/8 - 16 Flat Washer 3/8 Battery Hold Down Channel 22” Edger Battery Edger Battery Relay-Contactor RD Soc.
PAGE 15
Electrical System WHAT EVERY ICE RESURFACER SHOULD BE 13
PAGE 16
4 MAINTENANCE LOG Maintenance Log To assist you in maintaining a permanent record of your maintenance program for your new Olympia, keep track of all maintenance performed in the following log. Copy this form for additional pages as needed. Date Hours of Operation Maintenance Performed .............................................................................................................................................................................. .......................................