Quick Start Guide

Wire nuts x5
Dimmer Switch
Screws
Before you begin Install using
the Brilliant app
In the box Installation labels
Troubleshooting The Brilliant Smart
Home System
Works with Legal Legal
Step 1
Step 2
Download the app
Download the Brilliant app from the
Apple Store or Google Play Store.
Follow installation guide in app
Receive step-by-step installation
instructions using the Brilliant app.
Here’s what you need to know
before you expand your Brilliant
Smart Home System with the
Brilliant Dimmer Switch.
REQUIREMENTS
Brilliant Control: At least one Brilliant
Control must be installed for Brilliant
Switch to work.
Neutral & Ground Wires: Use the
Brilliant app to confirm that your
electrical wiring is supported.
Electrical:
- 120V AC
- up to 500W incandescent/halogen
- up to 200W LED/CFL
- Magnetic low voltage (MLV) lighting
not supported.
Tools: Non-contact voltage detector,
Philips screwdriver, standard
screwdriver, pliers
Want to learn more about what you can
do with your Brilliant Dimmer Switch?
Visit www.brilliant.tech
& more
Need additional help?
http://support.brilliant.tech
LED Status Indicator
White Blinking: Powered on and ready
to be set up
White Solid: Successfully set up and
connected to your home
Blue Blinking: Error detected, reset
Dimmer Switch
Reset Instructions
Quick Start Guide
NOTE: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must acceptany interference received,
including interference that may cause undesired
operation. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV
technician for help.
FCC CAUTION
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment. This transmitter
must not be co-located or operated in conjunction with
any other antenna or transmitter.
This device contains licence-exempt transmitter(s)/re-
ceiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1.This device may not cause interference. 2. This device
must accept any interference, including interference that
may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le
présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes
: 1. L’appareil ne doit pas produire de brouillage; 2.
L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en comprom-
ettre le fonctionnement.
Wire labels
Gang box labels
1 Ground Ground
1
1 Neutral Neutral
1
1 Line Line
1
1 Traveler Traveler
1
1 Load Load
1
Load
Pull out Safety Disconnect (clear plastic
tab over LED) until LED turns o.
Push in Safety Disconnect until LED
turns on.
Place your finger on Touch Plate and
hold for 6-10 seconds until LED
blinks white.
Transform any house or apartment into
an easy-to-use smart home.
1
2
3
SMART DIMMER SWITCH
Features
Motion Sensor
Set up with app
Slider
Dim lights:
Swipe up/down
Touch Plate
On/O:
Tap anywhere
Activate scene:
Double tap
LED
Set up with app
Safety Disconnect
Reset Dimmer Switch
Home Control
required
Dimmer Switch
Mobile AppSmart Plug
510-00008 REV 2
Line
Pantone 314 Pantone 1495
Front
1 2 3 4 5 6
7 8 9 10 11 12
Back

Summary of content (1 pages)