Before installing please note Exposed wire no longer than: 1-7/--- - 1 16 Inch (11mm) Please ensure 110 exposed w iring is visible.
Home Control Installation Guide THREE SWITCHES
Please confirm the following: Welcome! This short installation guide will help you upgrade your home with Brilliant. Is your circuit 120V? A 120V circuit is required, and is standard in North American homes. Is your wiring up to code, with Neutral and Ground wires? Both Neutral and Ground wires are required, and It is important that you first review all of the instructions to ensure you are comfortable with the required steps. present in most modern homes.
In the Box 10 STEPS To A Better Home Warning / Attention Base It’s important to only use supplied screws. Faceplate x3 Installing this product involves handling high voltage wiring. Each step of the enclosed instructions must be followed carefully. To avoid fire, personal injury, or death, turn off your circuit breakers and follow the proper safety precautions before proceeding. UNSURE ABOUT HANDLING ELECTRICAL WIRING? CONSULT A QUALIFIED ELECTRICIAN.
1 Check Compatibility Make sure Brilliant is compatible with the location where you’re installing it. If your light is controlled by...
Base If your light is controlled by... 3 or More Switches Will work: All Brilliant controllers (connected through WiFi) Will work: Brilliant at either end (or both ends) and a non-dimming switch 2 Turn Off Power Turn the circuit breaker to OFF.
Base 3 Remove Light Switch Unscrew your old switch cover and light switch from the wall. 4 Identify Each Circuit Single Pole (Go to 5a) One light switch that controls a light or set of lights. 3-Way/Multi-Way (Go to 6a) Two or more light switches that control the same set of lights. Pull the light switch out from the gang box, and take pictures of the wires, in case you need to reference them later. Then, disconnect the attached wires, and remove your old light switch.
Single Pole Single Pole 5a Identify Your Wires 5b Connect Wires Ground wire(s) (exposed green or copper) typically come from the wall box Black or Red Black or Red Black or Red Line and load wires (black or red) are connected to your old switch L1 L2 C x3 L1 L2 C L1 N L2 Green or Copper C When connecting less than three circuits, connect the closest terminals to ground.
Wires and Wire Nuts Wires and Wire Nuts are used to connect two or more wires together, or extend the length. They are not usually needed, but you will often use them for Neutral wires. Base Single Pole 5c Screws and Wires Step 1 Place wires in hole as deep as possible. Step 2 Turn screw clockwise with screwdriver. Step 3 Tighten until wires are secure. Test by tugging. Then go to Step 7 Select a wire extension from the box. Match the color of the wires you’re connecting.
3-Way/Multiway 6a Identify Your Wires Base 3-Way/Multiway 6b Connect Wires Red and Black Travelers Ground wire(s) (exposed green or copper) typically come from the wall box Common (black) is connected to your old switch L1 L2 C x3 L1 L2 C L1 N L2 Green or Copper C When connecting less than three circuits connect the closest terminals to ground.
Wires and Wire Nuts Wires and Wire Nuts are used to connect two or more wires together, or extend the length. They are not usually needed, but you will often use them for Neutral wires. Base 3-Way/Multiway 6c Screws and Wires Step 1 Place wires in hole as deep as possible. Step 2 Turn screw clockwise with screwdriver. Step 3 Tighten until wires are secure. Test by tugging. Select a wire extension from the box. Match the color of the wires you’re connecting.
7 Install Base 8 Test Lights Place wires in the gang box and attach the Base. Press Each Button Strain Reliefs Before Proceeding Avant de continuer The strain reliefs are designed to bend to accommodate differences in gang box styles and mountings. Some bending of the strain reliefs is normal, but be careful not to overtighten. Once the strain reliefs start to bend, you can stop.
9 Secure Faceplate Test the Base and secure the Faceplate. 10 Configure Brilliant Begin Configuration Tap the “Begin Configuration” button to start the process, and follow the prompts. Connect Wi-Fi Side Front Line up the brackets on the Base with the holes on the Faceplate. Press the Faceplate into the brackets and slide down until it clicks. The Faceplate will start up. Next, it will ask you to connect to Wi-Fi, and it is important to do this so you can access your other smart home devices.
Make your whole home Brilliant Once you’ve set Brilliant up, it’s easy to add more. They’ll automatically set themselves up and give you all the benefits of Brilliant throughout your home, including room-to-room video intercom and more. For help, educational videos, and additional Congratulations, you’re done with installation. product information visit us: http://support.brilliant.tech Have a more pressing question? email: support@brilliant.tech Use the Brilliant App to complete setup.
Removing and replacing the display frame with a new color Pull forward. Once the lower edge comes Step 1 upper hooks from the top edge of the Before proceeding, remove the Faceplate Faceplate. from the Base. Put one hand above it, and grab both sides with the other hand. Then, slide it up and off.
www.brilliant.tech Contains FCC ID:VPYLB1DX NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
