7231 Stainless Steel Gas Grill Parrilla de Gas de Acero Inoxidable OWNER’S MANUAL / MANUAL DEL PROPIETARIO ASSEMBLY AND OPERATING INSTRUCTIONS INSTRUCCIONES DE ARMADO Y OPERACIÓN SAVE THIS MANUAL FOR FUTURE REFERENCE GUARDE ESTE MANUAL PARA REFERENCIA FUTURA NOTICE TO INSTALLER: LEAVE THESE INSTRUCTIONS WITH THE GRILL OWNER FOR FUTURE REFERENCE. AVISO PARA EL INSTALADOR: ENTREGUE ESTAS INSTRUCCIONES AL PROPIETARIO DE LA PARRILLA PARA REFERENCIA FUTURA.
IMPORTANT SAFETY WARNINGS WE WANT YOU TO ASSEMBLE AND USE YOUR GRILL AS SAFELY AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL. WHEN YOU SEE THE SAFETY ALERT SYMBOL PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS! READ ALL SAFETY WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING AND OPERATING YOUR GRILL. DANGER IF YOU SMELL GAS: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open Lid. 4.
TABLE OF CONTENTS General Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation and LP Cylinder Specifications and Safe Use. . . . . . . . . . . . . . 4–6 Connecting LP Cylinder and Hose / Regulator to Grill . . . . . . . . . . . . . . . . 6–7 Leak Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8–9 Pre-start Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL WARNINGS WARNING • Never use natural gas in a unit designed for liquid propane gas. • Never use charcoal or wood briquets in a gas grill. Flavoring chips must be contained in a metal smoking box to contain ash and prevent fires. • Leak test all connections before first use, even if grill was purchased fully assembled and after each tank refill. • Never check for leaks using a match or open flame. CAUTION! Strong odors, colds, sinus congestion, etc. may prevent the detection of propane.
WARNING • FOR OUTDOOR USE ONLY. DO NOT operate indoors or in an enclosed area such as a garage, shed or breezeway. • Use your grill OUTDOORS in a well ventilated space away from dwellings or other buildings to prevent dangers associated with gas accumulation and toxic vapors. We recommend your grill be situated at least 10 feet (3.1 m) from buildings. • Maintain a minimum clearance of 36 inches (91 cm) between all sides of grill and walls or other combustible material.
CYLINDER SPECIFICATIONS: When purchasing or exchanging a cylinder for your gas grill, it must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S.
WARNING FILLING THE LP GAS CYLINDER: • Allow only qualified LP gas dealers to properly fill or repair your LP gas cylinder. • New tanks should be purged prior to filling; inform LP gas dealer if you are using a new tank. • DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled tanks can create a dangerous condition. Over-filled tanks can build-up pressure and cause the relief valve to expel propane gas vapors.
WARNING • Never use your grill without leak testing all gas connections and hoses. See the section on "Leak Testing" in this manual for proper procedures. WARNING The pressure regulator and hose assembly supplied with your gas grill must be used. • DO NOT attempt to connect it to any other fuel supply source such as a natural gas line. • DO NOT use any other pressure regulator/hose assembly other than the one supplied with your grill.
DANGER LEAK TESTING: To prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. • Never perform a leak test while the grill is in use or while grill is still hot. WARNING WHEN TO PERFORM A LEAK TEST: • After assembling your grill and before lighting for the first time, even if purchased fully assembled.
6. Check each place listed (A–K) for growing bubbles which indicates a leak. 7. Turn off gas supply at cylinder valve. 8. Turn on control knobs to release gas pressure in hose. 9. Turn control knobs to "OFF" position. 10. Tighten any leaking connections. 11. Repeat soapy water test until no leaks are detected. 12. Turn off gas supply at cylinder valve until you are ready to use your grill. 13. Wash off soapy residue with cold water and towel dry. 14.
WARNING Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any of the warnings and instructions contained in the preceding sections of this manual. WARNING LIGHTING INSTRUCTIONS: Follow the instructions exactly. 1. OPEN THE GRILL LID before attempting to light a burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the cylinder valve are turned to the "OFF" position. 3.
LIGHTING THE SIDE BURNER: 1. Open lid before lighting side burner. 2. Make sure control knob is in the "OFF" position. 3. Push and turn control knob to HIGH and continue to push knob in for 2 to 3 seconds to light burner. 4. If ignition does NOT occur in 5 seconds, turn control knob to OFF, wait 5 minutes to allow gas to dissipate and repeat lighting procedure. 5. To turn off, turn control knob clockwise until it locks in OFF position.
WARNING OPERATING THE GRILL: Never use charcoal or wood briquets in a gas grill. Flavoring chips must be contained in a metal smoking box to contain ash and prevent fires. Read and follow all warnings and instructions contained in the preceding sections of this manual. BREAKING IN YOUR GRILL: • In manufacturing and preserving the components of your grill, oil residue may be present on the burner and cooking surfaces of your grill.
ROTISSERIE COOKING: • Your grill was pre-drilled from factory to include mounting holes for a rotisserie (sold separately). Do not use a rotisserie not specifically manufactured for this grill. • Read and follow all instructions provided with the rotisserie. Save instructions for future reference. • Do not use the side burner when using a rotisserie.
GRILL COOKING TIPS CLEANLINESS • Always wash hands thoroughly with soap and hot water prior to handling food and after handling raw meat, uncooked poultry or seafood. • When using a platter to carry raw meat, uncooked poultry or seafood to the grill, make sure to wash the platter thoroughly with soap and hot water before placing cooked foods back on the platter or use different platters for raw and cooked foods.
CLEANING AND MAINTENANCE: • Keep the appliance free and clear of combustible materials, gasoline and other flammable vapors and liquids. • • Keep the ventilation openings of the cylinder enclosure free and clear of debris. Visually check burner flames for proper operation (see pictorial in "Burner Assembly/Maintenance" under Proper Care and Maintenance). Spiders or other insects can nest in the burner causing gas blockage.
COOKING GRILLS • Clean with mild soap detergent and water. A brass bristled brush or a nylon cleaning pad can be used to remove residue from the stainless steel surfaces. Do not use steel wire bristles to clean the cooking grills. Steel can cause the finish to chip or crack. DO NOT use a commercial oven cleaner. HEAT DISTRIBUTION PLATES • Periodically, it may be necessary to inspect and clean the heat distribution plate to prevent excess grease build-up. When the grill is cold, remove the cooking grills.
TROUBLE SHOOTING Problem: Burner will not light 1. Check LP cylinder fuel level. 2. Bad electrode spark. Check to see if the grill will match light. Electrode or collector may need adjustment. 3. Burner may not be properly seated. 4. Burner may be obstructed. 5. The cylinder valve may be closed. 6. Regulator is not properly seated on cylinder valve. Fire at control knob 1. Burner holes may be obstructed. See section on "Burner Assembly/Maintenance" under Proper Care and Maintenance. 2.
FREQUENTLY ASKED QUESTIONS Your grill's serial number and model number, and the contact information for Brinkmann Customer Service, are listed on a silver label found beneath the control panel, on the back of the grill or on the side of the grill body, under the side shelf. These questions and answers are for your general knowledge, and may not be applicable to your model grill.
FREQUENTLY ASKED QUESTIONS Cleaning Stainless Steel Cooking Grills: Wash grills with a mild detergent and rinse with hot water before initial use and as needed. DO NOT use a commercial oven cleaner. For stubborn food residue, use a degreaser and fiber or brass cleaning brush. Cleaning Porcelain-Finished Cast-Iron Cooking Grills: Wash grills with a mild detergent and rinse with hot water before initial use and as needed. For stubborn food residue, use a degreaser and fiber or brass cleaning brush.
PARTS BAG CONTENTS Make sure you have all items listed under PARTS LIST and PARTS BAG CONTENTS before you begin the installation process. Your Parts Bag will include: Qty. 26 2 2 18 2 Qty. 4 4 2 1 1 1 M6 X 12mm Bolts (Black) Wheel Axle Bolts Wheel Washers Star Washers (Black) M6 X 12mm Hexagonal Bolts (Silver) M6 Nuts (Black) #8 Self-Tapping Screws (Black) Lock Washers (Silver) AA /1.
ASSEMBLY INSTRUCTIONS READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN ASSEMBLING THIS UNIT.
1 3 2 4 6 5 8 7 10 11 12 9 13 14 16 15 18 19 17 20 21 26 22 23 24 25 27 FOR MISSING PARTS, PLEASE CALL CUSTOMER SERVICE AT 800-527-0717. (Proof of purchase will be required.) Inspect contents of the box to ensure all parts are included and undamaged.
Choose a good, cleared assembly area and get a friend to help you put your grill together. Lay cardboard down to protect grill finish and assembly area. CAUTION! Some parts may contain sharp edges. Wear protective gloves if necessary. Step 1 Attach cart base to side cart legs. Insert four M6 X 12mm bolts (black) and star washers (black) through cart base and into legs and tighten securely. Step 2 Attach loop strap bracket onto cart base by using two M6 X 12mm bolts (black).
Wheel Leg Hubcap Wheel axle bolt Washer Step 5 Install the wheels as illustrated, by inserting the wheel axle bolts through the wheels, washers and right side cart leg axle holes. Tighten axle bolts securely using hex nut wrench provided in parts pack. Step 6 Snap wheel hubcaps onto the outside of wheels as illustrated. Note: With the help of a friend, turn the cart to its upright position. Try to minimize the stress to the legs.
Step 9 Attach tank heat shield to heat shield plate using one #8 self-tapping screw (black). Note: When performing Step 10, Lift grill body from front and rear panels to avoid injury to hands and fingers. Step 10 With the help of a friend, place grill body assembly on grill cart. Grill body will rest between upper side sections of cart. Align bolt holes located on the inside of the grill body assembly. Secure using four M6 X 12mm bolts (black) with star washers (black).
Step 11 Attach side table front panel to side table with two M6 nuts (black) and star washers (black). Step 12 Attach hooks to side table towel rack bar. Then attach towel rack bar to side table using two M6 X 12mm hexagonal bolts (silver) and lock washers (silver). Step 13 Attach side burner assembly front panel to side burner assembly with two M6 nuts (black) and star washers (black).
Step 14 Attach side table to left side of cart frame assembly. Insert two M6 X 12mm bolts (black) into both left legs halfway. Place table over bolts and slide toward back of grill, then tighten securely. Fasten side table front panel to grill body with one M6 X 12mm bolt (black). Step 15 Attach side burner assembly to right side of cart frame assembly. Insert two M6 X 12mm bolts (black) into both right legs halfway.
Step 16 Side Burner Valve Burner Venturi Remove two M4 bolts and spring washers from the side burner valve. Insert the side burner valve assembly through the hole in the side burner table base, then firmly seat the valve nozzle into the burner venturi. Hold in place while you perform Step 17. WARNING: Never use your grill without leak testing all gas connections and hoses. See the section on "Leak Testing" in this manual for proper procedures.
Step 20 Place the side burner grate onto the side burner table. Step 21 Insert grease tray into tracks on backside of grill. Hang grease cup from brackets on botom of grease tray. Grease Cup Step 22 Insert tank lock wire through two small holes in cart base as illustrated.
Step 23 Warming Rack Place the heat distribution plates on lower level of grill body assembly directly above burners. Cooking Grills Heat Distribution Plates Step 24 Place cooking grills on support ribs directly above heat distribution plates. Step 25 Grooves Place warming rack in grooves so that it sits above the cooking grills. Step 26 Igniter battery holder is located under side table front panel. Remove igniter cap and insert battery with positive end of battery toward igniter cap.
ProSeries™ 7231 (Assembled) 31
IMPORTANTES ADVERTENCIAS DE SEGURIDAD ES NUESTRO DESEO QUE ARME Y UTILICE SU PARRILLA EN LA FORMA MÁS SEGURA POSIBLE. EL PROPÓSITO DE ESTE SÍMBOLO DE ALERTA DE SEGURIDAD ES QUE USTED PRESTE ATENCIÓN A LOS POSIBLES PELIGROS CUANDO ARME Y UTILICE SU PARRILLA. ¡CUÁNDO VEA ESTE SÍMBOLO DE ALERTA DE SEGURIDAD PRESTE ESPECIAL ATENCIÓN A LA INFORMACIÓN A CONTINUACIÓN! LEA DETENIDAMENTE TODAS LAS ADVER TENCIAS DE SEGURIDAD E INSTRUCCIONES ANTES DE ARMAR Y USAR LA PARRILLA. PELIGRO SI HUELE GAS: 1.
ÍNDICE Advertencias generales . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Instalación, especificaciones y uso seguro del cilindro de propano líquido . . . . . . . . . . . . . . . 35–37 Conexión del cilindro de propano líquido y de la manguera / regulador a la parrilla . . . . . . . . 37–38 Pruebas de detección de fugas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADVERTENCIAS GENERALES ADVERTENCIA • Nunca use gas natural en una unidad diseñada para gas de propano líquido. • Nunca use briquetas de carbón en una parrilla de gas. Los pedacitos de madera para dar sabor se deben colocar en una cajita de fumar de metal para contener la ceniza y para prevenir fuegos. • Realice una prueba de detección de fugas en todas las conexiones antes de usar la parrilla por primera vez, aún si compró la parrilla armada, y después de cada llenado del tanque.
ADVERTENCIA • PARA USO EXTERIOR ÚNICAMENTE. NO opere la parrilla en áreas interiores o en un área cerrada como un garaje, cobertizo o pasadizo. • Use la parrilla AL AIRE LIBRE en un espacio bien ventilado alejado de viviendas u otros edificios para prevenir los peligros asociados con la acumulación de gas y los vapores tóxicos. Recomendamos que la parrilla se sitúe a una distancia mínima de 10 pies (3,1 m) de los edificios.
ESPECIFICACIONES DEL CILINDRO Cuando compre o cambie un cilindro para la parrilla de gas, debe estar construido y marcado de acuerdo con las especificaciones para cilindros de gas de propano líquido del Departamento de Transporte (DOT) de EE.UU.
ADVERTENCIA LLENADO DEL CILINDRO DE GAS DE PROPANO LÍQUIDO: • Sólo los distribuidores de gas de propano líquido capacitados deben llenar o reparar su cilindro. • Los tanques nuevos deben ser purgados antes de llenarlos; dígale al distribuidor de gas si está usando un tanque nuevo. • NO permita que el cilindro sea llenado más del 80% de su capacidad. Los tanques llenados en exceso pueden crear una condición peligrosa.
ADVERTENCIA • Nunca use la parrilla sin haber verificado que no hay fugas en las conexiones y mangueras de gas. Consulte los procedimientos apropiados en la sección de "Pruebas de detección de fugas" en este manual. ADVERTENCIA Se debe utilizar el conjunto del regulador de presión y manguera suministrado con la parrilla de gas. • NO intente conectarla a ninguna otra fuente de suministro de combustible, como por ejemplo a una línea de gas natural.
PELIGRO PRUEBAS DE DETECCIÓN DE FUGAS: Para impedir los peligros de incendio o explosión: • NO fume ni permita que haya fuentes de encendido en el área mientras realiza la prueba de detección de fugas. • Realice la prueba AL AIRE LIBRE únicamente, en un área bien ventilada. • Nunca realice una prueba para detectar fugas con un cerillo o llama expuesta. • Nunca realice una prueba para detectar fugas mientras está usando la parrilla o con la parrilla caliente.
6. Inspeccione cada uno de los elementos indicados (A-K) para ver si hay burbujas, lo cual indica una fuga. 7. Cierre el suministro de gas en la válvula del cilindro. 8. Gire las perillas de control para descargar la presión de gas en la manguera. 9. Gire las perillas de control a la posición "OFF" (de apagado). 10. Apriete todas las conexiones con fuga. 11. Repita la prueba con agua jabonosa hasta que no detecte ninguna fuga. 12.
ADVERTENCIA Lea, entienda y siga todas las advertencias e instrucciones indicadas en este manual. NO pase por alto ninguna de las advertencias o instrucciones indicadas en las secciones anteriores de este manual. ADVERTENCIA INSTRUCCIONES DE ENCENDIDO: Siga las instrucciones al pie de la letra. 1. ABRA LA TAPA DE LA PARRILLA antes de tratar de encender una hornilla para que no se acumulen vapores dentro de la parrilla. Puede producirse una explosión si la tapa de la parrilla no está abierta. 2.
ENCENDIDO DE LA HORNILLA LATERAL: 1. Abra la tapa antes de encender la hornilla lateral. 2. Verifique que la perilla de control esté en la posición "OFF" (apagado). 3. Empuje y gire la perilla de control de la hornilla lateral a la posición "HIGH" (llama fuerte). 4. Oprima el encendedor electrónico en el panel de control principal y manténgalo oprimido 3 a 5 segundos para encender la hornilla. 5.
ADVERTENCIA OPERACIÓN DE LA PARRILLA: Nunca use briquetas de carbón en una parrilla de gas. Los pedacitos de madera para dar sabor se deben colocar en una cajita de fumar de metal para contener la ceniza y para prevenir fuegos. Lea y siga todas las advertencias e instrucciones indicadas en las secciones anteriores de este manual.
COCCIÓN ESTILO ROTISSERIE: • • • La parrilla viene preparada de la fábrica con agujeros de montaje para instalar un asador estilo rotisserie (vendido aparte). No use un asador estilo rotisserie que no haya sido fabricado especialmente para esta parrilla. Lea y siga todas las instrucciones incluidas con el asador estilo rotisserie. Guarde las instrucciones para referencia futura. No use la hornilla lateral cuando esté usando un asador estilo rotisserie.
RECOMENDACIONES PARA COCINAR EN LA PARRILLA LIMPIEZA • Siempre lávese bien las manos con agua caliente y jabón antes de manipular alimentos y después de tocar carne, pollo o mariscos crudos. • Cuando utilice una fuente para llevar carne, pollo o mariscos crudos a la parrilla, asegúrese de lavar bien la fuente con agua caliente y jabón antes de colocar alimentos cocidos en ella, o utilice fuentes distintas para los alimentos crudos y cocidos.
LIMPIEZA Y MANTENIMIENTO: • Mantenga el artefacto alejado de materiales combustibles, gasolina u otros vapores o líquidos inflamables. • Mantenga los orificios de ventilación del gabinete del cilindro sin residuos. • Observe las llamas de las hornillas para verificar que estén funcionando bien (consulte el dibujo en "Instalación/Mantenimiento de las Hornillas" en la sección de Cuidado y mantenimiento apropiados). Las arañas y otros insectos pueden formar nidos en la hornilla y bloquear el paso del gas.
REJILLAS PARA COCINAR • Límpielas con agua y detergente de jabón suave. Se puede usar un cepillo con cerdas de latón o una esponja de limpieza de nilón para quitar los residuos de las superficies de acero inoxidable. No use cerdas de acero para limpiar las parrillas de porcelana. El acero puede picar o agrietar el acabado. NO use un limpiahornos comercial.
IDENTIFICACIÓN Y CORRECCIÓN DE PROBLEMAS Problema: Causas posibles: 1. 2. • La hornilla no enciende 3. 4. 5. 6. 1. • Llamas en la perilla de control 2. 3. • • • La hornilla no se calienta lo suficiente • La parrilla está demasiado caliente Es posible que los agujeros de la hornilla estén obstruidos. Consulte "Instalación/Mantenimiento de las Hornillas" en la sección de Cuidado y mantenimiento apropiados. La hornilla está asentada incorrectamente sobre la válvula de control.
PREGUNTAS FRECUENTES El número de modelo y número de serie de la parrilla y la información para contactarse con el Servicio de atención al cliente de Brinkmann se incluyen en una etiqueta plateada abajo del panal de control o en el costado de la caja de la misma, debajo del estante lateral y tambien atras del assador en el panal. Estas preguntas y respuestas son para su conocimiento general y podrían no ser aplicables a su modelo de parrilla.
PREGUNTAS FRECUENTES Limpieza de las rejillas para cocinar de acero inoxidable: Lave las rejillas con un detergente suave y enjuáguelas con agua caliente antes del uso inicial y según sea necesario. NO use un limpiahornos comercial. Para residuos de alimentos persistentes, utilice un desgrasador y un cepillo de limpieza de fibra o latón.
CONTENIDO DE LA BOLSA DE PARTES Verifique que tiene todos los artículos indicados en la LISTA DE PARTES y en el CONTENIDO DE LA BOLSA DE PARTES antes de comenzar con el proceso de instalación. La bolsa de partes incluirá lo siguiente: Cant. 26 2 2 18 2 Cant.
INSTRUCCIONES DE ARMADO LEA DETENIDAMENTE TODAS LAS ADVERTENCIAS DE SEGURIDAD E INSTRUCCIONES ANTES DE ARMAR Y USAR LA PARRILLA RECOMENDAMOS QUE ESTA UNIDAD SEA ARMADA POR DOS PERSONAS Se necesitan las siguientes herramientas incluidas para armar esta Parrilla de Gas ProSeries™ 7231: • Destornillador de Punta Plana • Llave para Tuercas Hexagonales LISTA DE PARTES: 1 1 Conjunto del Cuerpo de la Parrilla 2 1 Mesa Lateral Izquierda 3 1 Conjunto de la Hornilla Lateral 4 1 Rejilla para Toalla de Mesa Lateral
1 3 2 4 6 5 8 7 10 11 12 9 13 14 16 15 18 19 17 20 21 26 22 23 24 25 27 SI FALTAN PARTES, LLAME A SERVICIO AL CLIENTE AL 800-527-0717. (Se requerirá el comprobante de compra.) Inspeccione el contenido de la caja para verificar que todas las partes estén incluidas e intactas.
Elija un lugar adecuado y despejado para armar la parrilla y pídale a un amigo que le ayude. Tienda cartón sobre el suelo para proteger el acabado de la parrilla y el área de armado. ¡CUIDADO! Algunas partes pueden tener bordes afilados. Póngase guantes de protección si es necesario. Agujeros para Pasadores de las Bisagras de las Puertas Paso 1 Conecte la base del carro a los paneles laterales.
Paso 5 Instale las ruedas tal como se ilustra, pasando los pernos del eje de las ruedas a través de las ruedas, las arandelas y los agujeros del eje de las piernas derechas. Ajuste los pernos del eje con una llave de cabeza hexagonal provista con las piezas. Paso 6 Empuje los tapacubos sobre la parte exterior de las ruedas, tal como se ilustra. Nota: Voltee el conjunto del carro con la ayuda de un amigo. Trate de minimizar la tensión sobre las patas.
Paso 9 Ate la protección contra el calor para el tanque a la lamina de protección contra el calor usando tornillo autoroscante #8 (negro). Nota: Cuando ejecute el Paso 10, levante la caja de la parrilla desde los paneles delanteros y traseros para prevenir lesiones a las manos y dedos. Conjunto del Cuerpo de la Parrilla Paso 10 Con la ayuda de un amigo, coloque la caja de la parrilla sobre el bastidor del carro. La caja de la parrilla se apoyará sobre la base angular de los soportes verticales.
Paso 11 Instale el panel delantero de la mesa lateral en la mesa lateral con dos tuercas M6 (negras) y arandelas de estrella (negras). Paso 12 Ate los ganchos de la rejilla para toalla de la mesa lateral. Entonces conecte la barra de la toalla a la mesa lateral usando dos M6 X 12 mm pernos hexagonales (plateados) y arandelas de cerradura (plateadas). Paso 13 Instale el panel delantero de la hornilla lateral en la hornilla lateral con dos tuercas M6 (negras) y arandelas de estrella (negras).
Paso 14 Instale la mesa lateral en el lado izquierdo del bastidor del carro. Inserte dos pernos M6 X 12mm (negros) en ambas piernas izquierdas a mitad. Coloque la mesa sobre los pernos y deslícela hacia atras de la parrilla, luego apriete bien. Conecte el panel delantero de la mesa lateral al cuerpo de la parrilla con un perno M6 X 12mm (negro). Paso 15 Instale el conjunto de la hornilla lateral en el lado derecho del bastidor del carro.
Paso 16 Remueva dos pernos M4 y arandelas de resorte de la válvula de la hornilla lateral. Inserte el conjunto de la válvula de la hornilla lateral a través del agujero en la base de la mesa de la hornilla lateral, luego asiente firmemente la boquilla de la válvula en el venturi de la hornilla. Manténgala en posición mientras ejecuta el Paso 17. ADVERTENCIA: Nunca use la parrilla sin haber verificado que no hay fugas en las conexiones y mangueras de gas.
Paso 20 Coloque la rejilla de la hornilla lateral sobre la mesa de la hornilla lateral. Paso 21 Inserte la bandeja de grasa en la abertura en el lado trasero de la parrilla. Asegúrese de deslizar la bandeja sobre los rieles, tal como se ilustra. Paso 22 Inserte alambre de cerradura de tanque por dos hoyos pequeños localizados en la base del carrito como ilustrado.
Paso 23 Coloque las placas de distribución de calor en el nivel inferior de la caja de la parrilla, directamente sobre las hornillas. Rejilla para Calentar Rejillas para Cocinar Cubiertas Térmicas Revestidas Paso 24 Coloque las rejillas para cocinar sobre las costillas de apoyo directamente sobre las placas de distribución de calor. Paso 25 Soportes Ponga la rejilla para calentar arriba de los soportes, de modo que quede asentada sobre las rejillas para cocinar.
ProSeries™ 7231 (Armada) 62
FOR GRILL REPLACEMENT PARTS, COVERS & ACCESSORIES, PLEASE VISIT US ONLINE AT www.grillpartsonline.com PARA ENCONTRAR PARTES DE REEMPLAZO PARA SU PARRILLA, CUBIERTAS Y ACCESORIOS, FAVOR DE VISITARNOS AL www.grillpartsonline.