INSTR_821-7000-0_SL7.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 2 HOW YOUR HOME SECURITY MOTION ACTIVATED LIGHTING SYSTEM WORKS The Home Security Motion Activated Lighting System is designed to turn on automatically at night when a person enters the detection zone. The light will stay on as long as the motion detector senses motion in the zone. The light will turn off in approximately 90 seconds after the person leaves the detection zone or stops moving.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 3 ASSEMBLY INSTRUCTIONS Inspect contents of the box to ensure all parts are included and undamaged. 3 A Phillips screwdriver will be required. 4 1 PARTS LIST: 1 Home Security Main Housing 2 Main Housing Mounting Screws (2) 3 Solar Panel Module with Cord 4 Solar Panel Module Mounting Screws (3) 5 SL-7 Owner’s Manual 2 Step 1 Select a location and attach the main housing where you want to detect persons or objects moving at night.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 4 Step 3 Slide the two slots in the back of main housing onto the screws. Step 4 Select a location within 15 feet from the main housing to mount the solar panel module. The solar panel module must be mounted where it will receive FULL, DIRECT SUNLIGHT for several hours each day. Step 5 Firmly plug the solar panel module cord into the main housing.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 5 Step 8 Point the two floodlights in the desired direction. You may want to adjust the floodlights after letting the unit operate for a few nights. Motion Detector Head Step 9 Position the detector head in the direction you want to cover. Never aim the motion detector head directly at the sun or above a 90° angle (horizontal level). Do not rotate the head more than 360°.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 6 TESTING INSTRUCTIONS Step 1 After installing your light, leave the switch in the “OFF” position and charge in FULL, DIRECT SUNLIGHT for THREE FULL SUNNY DAYS. Step 2 After allowing the battery to fully charge, the motion detector can be adjusted and tested. Point the motion detector head down 15° from horizontal level. Step 3 Move the slide switch to “TEST” position. Turn the range knob all the way to the minimum setting (counterclockwise).
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 7 Changing Bulb Bulb 1. Turn lens counterclockwise and remove. Lens 2. Pull bulb straight out and replace with new bulb. DO NOT PLACE NEW BULB IN BRASS GROMMET HOLES. 3. Replace the lens by aligning the slots with the grooves in the top housing and turning clockwise to lock in place. Changing Batteries 1. Unscrew the four screws in front housing and separate it from rear housing. 2.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 8 It is important that the solar panel is kept free of dirt and debris. A dirty solar panel will not allow the battery to fully charge. This will shorten the life of the battery and cause the light to malfunction. Clean regularly with a dampened cloth or paper towel. Cleaning Solar security lights can be left outside year round, even in cold weather.
INSTR_821-7000-0_SL7.qxd 5/17/06 After installing the main housing and solar panel module, leave the switch in the “OFF” position and charge in FULL, DIRECT SUNLIGHT for THREE FULL DAYS. Then remove the switch label and slide the switch to the “AUTO” position. The light will turn on automatically at night when it detects motion. Page 9 b. If the weather has been cloudy or overcast during the day, the battery will not be charged for operation at night.
INSTR_821-7000-0_SL7.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 11 HOME SECURITY ACCESSORIES For Visa/MasterCard orders, please call 800-468-5252, Monday through Friday, 8:30 AM - 5:00 PM Central Standard Time. 100-0057-0 Replacement Bulb 070-6001-0 SL-7 Replacement Battery 112-0010-0 15 ft.
INSTR_821-7000-0_SL7.qxd 5/17/06 4:29 PM Page 12 © 1996 The Brinkmann Corporation Dallas, TX 75244 www.brinkmann.net ONE YEAR LIMITED WARRANTY For one year from date of purchase, The Brinkmann Corporation warrants the Home Security Motion Activated Lighting System against defects due to workmanship or materials to the original purchaser. The Brinkmann Corporation’s obligations under this warranty are limited to the following guidelines: • This warranty does not extend to the bulb or batteries.
