Owner's Manual 42" Grader Blade MODEL: BB-56 • • • • Assembly Installation Operation Repair Parts Recommended for use with Garden Tractors with Grader Blade. Tire chains and wheel weights are recommended. IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! For the latest product updates and setup tips: Visit us on the web! www.brinly.com L-1434 Rev.
INTRODUCTION CONGRATULATIONS on the purchase of your new Brinly-Hardy Grader Blade! Your Grader Blade is designed, engineered and manufactured to give you the best possible dependability and performance. CUSTOMER RESPONSIBILITIES Please read and retain this manual. The instructions enables you to assemble and maintain your Grader Blade properly. And please, always observe the “Safety” instructions. TABLE OF CONTENTS SAFETY....................................................................................
SAFETY TO HELP PREVENT BODILY INJURY DUE TO LOSS OF STABILITY OR CONTROL: • Read the vehicle's owner's manual, your tractor's owner's manual, and this owner's manual before using this Grader Blade. • Know controls and how to stop quickly. • Do not allow children to operate the vehicle, do not allow adults to operate without proper instruction and without having read the owner's manual. • Do not carry passengers. Keep children and pets a safe distance away. • Always wear substantial footwear.
PARTS REFERENCE 5 20 STOP 13 2 4 Installation Questions? Missing Parts? Replacement Parts? DON’T GO BACK TO THE STORE! Please call Customer Service Department Toll Free 877.728.8224 or customerservice@brinly.com 1 6 10 8 11 19 18 15 7 14 9 16 17 3 12 L-1434 Rev.
PARTS REFERENCE Item # Part # Description Qty Item # Part # Description Qty 1 45M4440P Washer, 1-1/4" 1 11 2M1620P Hex Bolt, 1/2" x 1-1/4" 4 2 B-1675P Locknut, 3/8"-16 1 12 10M1216P Carriage Bolt, 3/8" x 1" 4 3 B-2375-10 42" Blade Black 1 13 10M1240P Carriage Bolt, 3/8" x 2-1/2" 1 4 B-2376-10 Angling Bar Black 1 14 30M1200P Hex Nut, 3/8" 4 5 B-2578 Clevis Pin, 7/16" x 2-3/8" 1 15 30M1600P Hex Nut, 1/2" 4 6 B-3717 Vinyl Grip 1 16 40M1200P Lockwasher, 3/8"
ASSEMBLY Figure 2 20 3. Install Large Flat Washer over Drawbar Post. Slide Angling Lever over Drawbar Post and assemble with Clevis Pin and Cotter Pin in outermost holes. 2 5 13 4 1 4. Install Carriage Bolt and Locknut into innermost holes. 5. Install Vinyl Grip onto Lever. 6. Assemble Hitch to Drawbar as shown. 6 11 19 18 14 9 1 1-1/4" Washer Qty. 1 2 3/8" Locknut Qty. 1 14 3/8" Nut Qty. 4 20 1/8" x 1" Cotter Pin Qty. 1 L-1434 Rev. B 18 1/2" Lockwasher Qty.
ADJUSTMENT Figure 3 6. Attach the blade to the sleeve hitch on your tractor using the middle holes in the blade hitch. 9. The stabilizer bolts on the hitch should be tightened against the yoke on drawbar to prevent any "side sway" during the operation of the blade. 7. Position the tractor (with blade) on a hard, level surface. Lower the blade and check to make sure it is level, side 10. The operating depth of the blade needs to be set now.
MANUFACTURER'S LIMITED WARRANTY FOR Pull Behind Accessories The limited warranty set forth below is given by Brinly-Hardy Company with respect to new merchandise purchased and used in the United States, its possessions and territories. Brinly-Hardy Company warrants the products listed below against defects in material and workmanship, and will at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.