Owner's Manual CULTIVATOR MODEL: CC-560 • Assembly • Operation • Repair Parts For use with Garden Tractors. A Sleeve Hitch Accessory is required for operation. Wheel weights and chains are also recommended. IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! For the latest product updates and setup tips: Visit us on the web! www.brinly.com 1007076 Rev.
INTRODUCTION CONGRATULATIONS on the purchase of your new Brinly-Hardy Cultivator! Your cultivator is designed, engineered and manufactured to give you the best possible dependability and performance. CUSTOMER RESPONSIBILITIES Please read and retain this manual. The instructions enables you to assemble and maintain your lawn aerator properly. And please, always observe the “Safety” instructions. TABLE OF CONTENTS SAFETY/OPERATION/MAINTENANCE........................................ 2-3 PARTS BREAKDOWN .....
SAFETY/OPERATION/MAINTENANCE OPERATE SAFELY KEEP BODY PARTS FROM UNDER TOW BAR • Use this machine for intended purpose only. Before disconnecting this machine from towing vehicle hitch: • Speed should always be slow enough to maintain control. Travel slowly over rough ground. • Stop on level ground. • Stop towing vehicle engine. • Lock towing vehicle park brake. • Block wheels of the machine. • Make sure body parts are not under tow bar.
PARTS BREAKDOWN 8 10 3 STOP 20 17 9 2 13 18 16 14 Installation Questions? Missing Parts? Replacement Parts? DON’T GO BACK TO THE STORE! Please call Customer Service Department Toll Free 877.728.8224 or customerservice@brinly.com 19 15 4 11 10 10 10 5 19 15 7 19 21 20 19 1 15 17 15 19 6 15 ITEM NO. DESCRIPTION PART NO. 14 12 QTY. ITEM NO. DESCRIPTION PART NO. QTY.
ASSEMBLY Figure 1 HITCH BRACKET AND TIE STRAP ASSEMBLY 10 TOOLS REQUIRED: 3 9/16" Wrench (1) 3/4" Wrench (2) 11/16" Wrench (1) 9 13 2 18 16 15 1a. Loosely assemble Hitch Bracket (2) to Pull Bar (3) using Plow Bolts (13), 7/16" Lockwashers (18), and 7/16" Nuts (16) as shown. DO NOT TIGHTEN. NOTE: It is important to orient Plow Bolts in direction shown. (13) Plow Bolt, 7/16" x 1-3/4" Qty. 2 19 (18) Lockwasher, 7/16" Qty. 2 (15) Nut, 7/16" Qty. 2 (19) Lockwasher, 1/2" Qty.
ASSEMBLY Figure 3 FRAME TIE BAR ASSEMBLY 4 3a. Assemble Tie Bars (5) to Frame Angles (4) using 1/2" x 1-1/2" Bolts (10), 1/2" Lockwashers (19), and 1/2" Nuts (15). 11 10 5 3b. Assemble Tie Bars (5) to Pull Bar (3) using 1/2" x 2" Bolt (11), 1/2" Lockwasher (19), and 1/2" Nut (15). 3 19 15 19 3c. Tighten hardware from Step 2a. (10) Bolt, 1/2" x 1-1/2" Qty. 2 Figure 4 15 (19) Lockwasher, 1/2" Qty. 3 (15) Nut, 1/2" Qty. 3 (11) Bolt, 1/2" x 2" Qty. 1 SPRING SHANK ASSEMBLY 4a.
ASSEMBLY Figure 5 GAUGE SHOE ASSEMBLY 5a. Assemble one of the Gauge Shoe halves (7) to Frame Angle (4) using 1/2" x 1-1/2" Bolts (10), 1/2" Lockwashers (19), and 1/2" Nuts (15). Note slot orientation in illustration. 10 4 7 20 5b. Attach Gauge Shoe halves (7) together using 3/8" x 1" Carriage Bolt (12), 3/8" Washer (20), 3/8" Lockwasher (17), and 3/8" Nut (14). (12) Carriage Bolt, 3/8" x 1" Qty. 2 Figure 6 14 19 15 (10) Bolt, 1/2" x 1-1/2" Qty. 2 17 (19) Lockwasher, 1/2" Qty.
MANUFACTURER'S LIMITED WARRANTY FOR Pull Behind Accessories The limited warranty set forth below is given by Brinly-Hardy Company with respect to new merchandise purchased and used in the United States, its possessions and territories. Brinly-Hardy Company warrants the products listed below against defects in material and workmanship, and will at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.