SINCE 1839 BRINLY_ PLOW 10-INCH OWNER'S MANUAL SERIES NO. PP-51 MODEL NO. PP-51 0 • Assembly e Installation • Operation • Repair Parts THIS IMPLEMENT FOR USE WITH GARDEN TRACTORS EQUIPPED WITH SLEEVE HITCH. ALSO, TIRE CHAINS AND WHEEL WEIGHTS ARE RECOMMENDED. "IMPORTANT: THIS MANUAL CONTAINS INFORMATION FOR THE SAFETY OF PERSO·NS AND PROPERTY.
CONGRATULATIONS on your purchase of this Brinly Implement. It has been designed, engineered, and manufactured to give you the best possible dependability and performance. Please read and retain this manual. T~~ instructions will enable you to assemble and maintain your Implement properly. Always observe the IISAFETY RULESII. Should the need ever exist for repair parts, order through most any Lawn and Garden dealer, using part number and description.
Z-1216No.1 B-1674P Hex (Lock) Nut, 5/16 11 3 Used No. 26 P-597 Spacer 11 5/8 1.0. x 1/2 11 2 Used. No. 35 15M1632P No.3.8-1678P Hex (Lock) Nut, 5/8 11 No. 28 1M1624P 2 Used. Hex Head Bolt 1/2 x 1-1/2 11 No. 29 1M1628P Plow Bolt Hex Head Bolt 1/2 x 2 1/2 11 11 11 x 1-3/4 11 11 1 Used ,2 Used 2 Used No. 42 45M1111P No. 39 30M2000P Hex Nut, 5/8 Flat Washer, 5/16 11 No. 44 45M1717P 11 11 I 1 Used 3 Used 2 Used Flat Washer 1/2 No.
Z-1216-C HARD ARE BAG --- No.6 P-172P ._- -==- -~-- 0' Coulter Axle _ LUsed. No. 23 P-386P "Ull Bolt 1 Used IT IS RECOMMENDED THAT YOU CAREFULLY READ THIS OWNt;R~$ MANUA~ ~EFOR.E STARTING ASSEMBLY OF THE UNIT. • Before starting assembly; arrange each kind of hardware into a group to ease assembly. • Right hand (R.H.) and left hand (L.H.) are determined from the OPERATOR'S position while seated on the tractor. • PLOW FRAME Refer to Fig.
PLOW BOnOM AND STANDARD • • 1/2" X 3/8" x 1" Refer to Fig. 2 Assemble the landside to frog- using two 3/8" x 1 plow b-olts and 3/8" hex nuts. Attach standard to frog using 1/2 x 2" plow bolt and 1/2 hex nut as shown. Insert the 1/2" x 1-1/2 carriage bolt through frog and standard and secure with a 1/2 hex nut. Insert one 1/2 x 1-1/2" Hex Bolt (Tracking Adjusting Bolt) through the "tab" at the bottom of standard.
. PREADJUSTMENT (Refer to Fig. 5 and 6) Note: During normal plowing, the right side Tractor Wheels will be riding in the previously plowed furrow. A furrow is the cut area your plow makes when turning the soil. An initial setting for your plow is required to cut the first furrow on level ground. The following pre-sets will result in an approximate 5 to 6 plowing depth. • Remove Stabilizer Bolts and Nuts from Sleeve Hitch. The plow must be free to move side to side on Hitch.
PLOWING TIPS ., Layout your field to be plowed, and if possible make it. rectangular in shape. Note: It is easier to plow a few long furrows than many short ones. Leave some room at each end of the field for turning your tractor. • ALWAYS LIFT THE PLOW BEFORE. TURNING!!! • Do not plow too fast! Move steadily along so that the earth will turn over and not fall back into the furrow. In most soils, this is done at FULL THROTILE in Third Gear.
DEPTH ADJUSTMENT Refer to Fig. 8 Depth Crank~.., • To turn the plow share into the ground to open the "first" furrow, adjust the point downward until the plow is cutting 4 to 5" deep. • After a few furrows, (or desired depth is reached) turn the crank COUNTER-CLOCKWISE to maintain that depth. Do not allow landside to ride more than 1/2" off bottom of furrow as this will cause excessive wear on. bottom of share resulting in poor soil penetration and loss of landside support. ____·..nr--~_~ . . -..·0 ...'.
TROUBLE SHOOTING (PLOWING DIFFICULTIES AND REMEDIES] PROBLEM CAUSE/CONDITiON REMEDY F • SLOW GROUND ENTRY PLOW CUTIING TOO WIDE improper Crank Adjustment. Refer to Depth Adjustment and turn crank CLOCKWISE 1 or 2 turns at a time. • Badly' worn Plow Share. Replace with a new Share. • Ground extremely dry and hard due to lack of moisture. Add extra weight to tractor or wait, until soil conditions are suitable. • Hitch downward movement restricted by mower height adjustment.
MOLDBOARD PLOW I 18 PARTS LIST Ref. No. 1 2 3 5 6 7 8 9 10 11 12 13 14 15 16 1'7 18 19 20 21 22 23 24 Part No. B-1674P B-1677P B-1678P D-128P P-172P P-234 P-250A P-251-10 P··609··10 P-256P-01 P-257-10 P-260-01 P-262-01 P-26SA-10 P-269A-1'O P-270 P-27'2A-10 P-273-10 P-275-10 P-278 P-287-10 P-386P P-387-01 t -104:i· 3 Description 11 Hex Lock Nut, 5/16 Hex Lock Nut, 1/2 Hex Lock Nut, 5i8 Grease fitting, 5/16 Coulter Axle Spacer, 1/2 1.0.
