Instructions / Assembly

tube
"U
ll
Bolt
Coulter blade
Frog ~
1/2
11
x 1-1/21l~
Hex bolt-
(Tracking Adjusting) 1/2" Hex nut'
__ 3j~/ Hex nuts
FIG. 2
Standard -
1/2" Square nut
FIG. 3
~=-~=---- ...
5/16" X 3/4" Carriage bolt
5/16" Locknut
Cotter pin \
1/8
11
X 1-1/4
11
5/8
11
.~
Flat washer
. /
_/~
v~.... Coulter hub
1
/2" X 2" Plow bolt
3/8" x 1" \_ 1/2" x 1-1/2"
P~~, Carriage bolt
Landslde
\
A WARNING
• The "Attachment Clutch" Switch on dash of Tractor
(device that engages Tractor Mower) needs to be
ENGAGED at all times while operating Tractor. This
actuates the Operators Sensing Device in the Tractor
seat ---Tractor Engine will stop in case you dismount
or fall
off Tractor. Failure to actuate this device
can cause personal injury or damage
to your Tractor
and Property if you were to fall off. SWITCHMUSTBE
DISENGAGED IN
ORDER TO RESTART ENGINE!
PLOW FRAME AND BOTTOM (Refer to Fig. 3)
• Straddle the beams over standard and fasten together
at the LOWER hole in the standard with one
1/2" x 1-3/4
11
bolt and 1/2" hex lock nut.
• Attach end of threaded tube to side of standard at
the UPPER hole with a 1/2
11
X 1-1/2" hex bolt followed by
the 1/2
1t
flat washer, then place the 9/16" spacer in the
hole in standard and secure this assembly with one - 1/2"
hex lock nut.
• Tighten these fasteners so that the threaded tube is
free to pivot.
• Refer to the coulter adjustment section for proper set-
ting, to be adjusted
AFTER you begin plowlnq.
cou,TER BLADE (Refer to Fig. 4]
• Insert coulter standard into fork, align the holes and
drive the 5/16" x
1-1/4
11
pin through, leaving an equal
amount of pin on each side.
• Attach the coulter hub to the coulter blade using
three
5/16
11
XI3/4
11
carriage bolts, 5/16" flat washers, and
5/16
11
lock nuts. .
• lnstall the coulter blade on the fork
by insert ing
the axle through one leg of the fork, the coulter
hub, and other leg of fork. Secure with the two
5/8" flat
washers and
1/8
11
x 1-~/4tt cotter pin, bend the legs over.
• Attach the coulter assembly to the plow beam as
shown, using the "U" bolt, coulter clamp, two spacers
(locate -BETWEEN the plow beams), and secure with two
5/8
11
h-ex nuts.
• Position the coulter standard between the
"Uti bolt and
coulter clamp and move up to the highest position.
PLOW BOnOM AND STANDARD
Refer to Fig. 2
• Assemble the landside to frog- using two 3/8" x 1
11
plow b-olts and 3/8" hex nuts.
• Attach standard to frog using
1/2
11
x 2" plow bolt
and
1/2
11
hex nut as shown.
• Insert the
1/2" x 1-1/2
11
carriage bolt through frog
and standard and secure with a
1/2
11
hex nut.
• Insert one
1/2
11
x 1-1/2" Hex Bolt (Tracking
Adjusting Bolt) through the "tab" at the bottom
of standard. Place the
1/2
11
Square nut between
the "Tab" and Frog, and thread the Tracking
Adjusting Bolt into the square nut until tight.
• Tighten all fasteners securely.
5
FIG. 4