Instructions / Assembly
B-C
Point of Plow Share
FIG. 5
--
....
;'
.....
/;
~
"
lE~A
Bi
F
t I
1 1
t 1
.
4za
X-A
Centerline of Plow
Coulter Axle Bolt
PREADJUSTMENT (Refer
to
Fig. 5 and 6)
Note: During normal plowing,
the
right
side Tractor Wheels
will
be
riding
in the previously
plowed
furrow. A
furrow
is the
cut
area
your
plow
makes when
turning
the soil.
An initial setting for your plow is required to cut the
first
furrow
on level ground. The
following
pre-sets
will
result in an approximate 5
11
to 6
11
plowing
depth.
• Remove Stabilizer Bolts and Nuts
from
Sleeve Hitch.
The
plow
must be free to move
side
to side on Hitch.
• Lower
your
Tractor Lift Handle and
lock
in Lowered
Position. You may need
to
Lower
the
"Attachment Depth
Control" on your Tractor
to
do
this.
•
Mount
the
Plow to the Sleeve Hitch
with
the Hitch Pin
furnished
with
the
Hitch. Refer
to
Figure
1 and Table 1
to
select
the
proper
mounting
hole.
• Adjust
Lift
Spring Tension on Hitch as required, see
Hitch Manual for instructions.
• Ad-just
the
Depth Crank
of
Plow
until Point
of
Plow Share is on the ground and
the
rear
of
Plow
Landside is
approximately
1
lJ
off
the
ground. (Refer
to Figure 5)
Note: The Plow will appear
to
be angled
to
left.
This
will
allow
the Plow
to
run level when the
Right Hand Tractor Wheels are in
the
plowed
furrow.
F-G
Start
f i
t t
O-X~C-G
..
.
,
...
_-",'
/ D-E
Furrow
stop
the Tractor and measure
the
distance
from
the
centerline of the
Plow
Coulter
Axle
Bolt
--- it
should be
about
2
11
above the ground. If it is not,
raise the Plow
out
of
the
ground
and
adjust
the
Coulter
up or
down
to
obtain
this
dimension. Be
sure to
adjust
side
motion
at
this
time.
(See
Coulter
Adjustment
page
8)
FIG. 6
retry until the 5
11
to
6
11
depth
is
obtained.
• After
..
plovy
ing
depth
is set
with
plov/· in
fUrrO\N
t
therefore, the Pitch
(Depth)
of
the
Plow
must
be
readjusted to a 5
11
to 6
11
plowing
depth.
•
Position
your Tractor
with
the
inside of the
Right (Side) wheels against
the
side of the
previously plowed furrow.
• Start
plowing
for a short
distance
and check
the
depth of the furrow. Adjust the Depth Crank Clock-
wise or Counter-Clockwise ONE
turn
at a
time
and
TRACKING ADJUSTMENT (OPTIONAL)
Note: If the Plow appears to
track
to
the (eft Standard and
turning
the
Tracking
Adjustment
Bolt
while
plowing, an adjustment is available
to
correct
Clockwise
~)
two
turns. Retighten
Hex
Nuts
this condition. (Refer to Figure 9) securely. Repeat
Adjustment
as necessary
until
plow
eThe
Tracking Adjustment is
made
by loosening
both
pulls
straight
at 10"
from
the
adjacent
plowed
1
/2
11
Hex
Nuts securing
the
Plow
Bottom
to
the 6 swath.
•
Adjust
the
Plow Couiter
to
its highest position.
• Go and make
your
first
two
furrows
as described
in the diagram
(X
to
A and turn B to
C).
Make
sure
the
Tractor
Lift
Handle is Lowered and
Locked
into
the
down
position. Plow in Third Gear and near
Full Throttle. Raise the Plow
to
the
Transport
Position when turning.
• If
your
Plow is
not
plowing
at 4
11
to
5
11
deep
on
your
initial
two
passes,
readjust
the Plow Depth
Crank by turning
it clockwise (
.........
)
to
go
deeper
or counter-clockwise
~)
to
go shallower. (See
Fig.
8) Make
this
adjustment ONE TURN at a
time
until desired depth is obtained.
Note:
The rest
of
the furrows
will
be made
with
the
Tractor
Ilres In the previously
cut
furrows;