Operator's Manual Model P40/S40 Series IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! Spyker Spreaders Contact Us at 800.972.6130 ©2010 Brinly-Hardy Co. 1007895 Rev.
62 Hopper Explosion 27 69 63 28 29 15 Rate Gate and Deflector Explosion 24 20 26 19 21 25 24 6 4 22 5 17 19 64 7 72 8 73 4 12 73 6 3 2 5 72 6 Handle Explosion 65 68 1 1007895 Rev.
16 14 44 Spinner/Axle Explosion 70 47 45 43 53 58 48 50 51 55 49 49 59 56 14 50 52 40 54 33 57 60 3 Frame Explosion 3 18 18 3 9 6 3 18 6 6 42 3 6 4* 42 40 33 13 13 3 4* 6 3 3 41 61 41 43 3 61 41 6 11 9 10 *As needed for shimming 3 1007895 Rev.
Item Part Number 1 Qty Description Item Part Number Qty Description 1007770-01 1 Handle Stainless 36 N/A Number Not Used 1008052-10 1 Handle Painted 37 N/A Number Not Used 2 1007773 1 Control Lever 38 N/A Number Not Used 3 05-90-0054 12 1/4" x 1-1/2" Bolt, SS 39 N/A Number Not Used 4 05-92-0008 6 1/4" Washer, SS 40 05-90-0065 1 5 05-94-0051 2 Nylon Flange Bushing 3/16" x 1-3/4" Clevis Pin 6 SS-91-0004 17 41 05-92-0004 3 Flat Washer, SS 7 05-90-0121 1 1/4"
1. Install Linkage to Lever as shown, Figure 1. Figure 1 2. Turn Handle Assembly sideways and install Linkage into Rate Gate Lever as shown, Figure 2. 3. Attach Handle Assembly to Frame using (4) 1/4 x 1-1/2" long Bolts and 1/4" Nylon Insert Locknuts, Figure 3. Figure 2 Figure 3 5 1007895 Rev.
4. Install Handle Grips on Handle of Spreader, Figure 4. Figure 4 1007895 Rev.
READ BEFORE USING OPERATE SAFELY Do not wear loose fitting clothing that can get caught in moving parts. Keep bystanders away when you operate this machine. Use this machine for intended purpose only. Always wear eye protection when operating the equipment. Do not let children or an untrained person operate machine. Stay alert for holes in the terrain and other hidden hazards. Keep all parts in good condition and properly installed. Fix damaged parts immediately. Replace worn or broken parts.
READ BEFORE USING Become Familiar With The Operation Of The Spreader Before You Put Material In The Hopper • Practice walking with the spreader, opening and closing the rate gate at the appropriate times. • Travel at a constant speed and operate the spreader lever position. Remember: Open the rate gate after the spreader is in motion at operating speed (about 3 mph, or at a brisk walking pace). • dial setting on the low side. If the setting proves to be too low, cover the area more than one time.
READ BEFORE USING Now You Are Ready To Put Material In The Hopper • WARNING: Avoid Injury! Chemicals can be dangerous. Avoid injury to operators or bystanders. • Make sure the rate gate is in the closed position. • Read chemical container label for handling instructions. A Material Safety Data Sheet (MSDS) should be supplied by the chemical dealer and provides proper safety information. • Wear proper clothing and safety equipment while handling or applying chemicals.
ACCUWAY - What It Does The Accuway Spread Pattern Equalizer Balances the spread pattern - Bulls Eye - Dead to the Center of the Spreader. All products. All spreading conditions. Skewing is eliminated. Does not change the spread width. ACCUWAY - How It Works Accuway shifts the material placement on the spreader spinner fan. This in turn, balances the pattern heavier to the right or heavier to the left.
NOTE: Dial Settings Are Approximate Only ! Product Particle Size Fine Pellets Mixed Fine Pellets Small Pellets Nitrogen Pellets Medium Size Medium Pellets And Granuals Large Heavy Pellets Lbs. per 1000 sq. ft. Dial Settings Full Rate Once Over Dial Settings Half Rate Twice Over 1 3.6 3.1 2 3 4.0 4.2 3.5 3.7 2 3.7 3.2 4 6 4.7 5.2 4.1 4.5 2 2.2 4 3 4.2 6 4.5 1 3.5 3 2 3 4.2 3.7 4.7 4 2 3.5 3 4 6 4.2 5.2 3.8 4.5 2 3.8 4.9 5.9 3.3 4.1 4.9 4 6 3.
1 YEAR LIMITED WARRANTY This is warranted to the original purchaser only. Spyker will replace parts with defects in materials and workmanship, for a period of one year from the date of purchase. For Spyker Spreaders–a Brinly-Hardy Company, products employing metal gear systems, pinion and bevel, these metal gears, only, not inclusive of any other parts or materials, are warranted for the life of the spreader, not to be used for replacement or repair past original purchase.