OWNER'S MANUAL LAWN SWEEPER MODEL: STS-427LXH • Assembly • Installation • Operation • Repair Parts Visit us on the web! www.brinly.com Important: This manual contains information for the safety of persons and property.
INTRODUCTION AND SAFETY ================================================================================================ CONGRATULATIONS on the purchase of your new Brinly-Hardy Sweeper! Your Sweeper has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please do not hesitate to contact our knowledgeable customer service department toll-free at 1-877-728-8224.
CAUTION SHOULD BE TAKEN WHEN TOWING AND/OR USING ANY ATTACHMENT. ================================================================================================ This attachment combined with the weight distribution, turning radius, and speed of GENERAL NOTES (Operation) towing vehicle can result in severe injury or death to operator, damage to towing vehicle, and/or attachment if not used properly.
PARTS ================================================================================================ REF PART NO. DESCRIPTION QTY REF PART NO.
25 PARTS 19 16 ================================================================================================ 18 7 10 3 10 19 25 19 19 10 19 25 19 27 14 32 25 25 19 19 10 16 19 19 18 19 23 TOW TUBE COMPONENT VIEW 4 25 27 25 7 10 25 68 26 * On newer models, the tapping screws (63) have been replaced with molded-in clips attached to the dust cover (42). 30 41 2 1 9 A diagram has been provided with instructions for removal of the new dust cover. (See pg 22).
ASSEMBLY ================================================================================================ TIP 1: An organized skinpack with all necessary hardware has been provided with this product. Be sure to use the hardware panels called for in each step of the assembly. NOTE: Hardware Panels 08 and 09 will not be used in this assembly.
ASSEMBLY 11” (top of page) ================================================================================================ 10” STEP 2 -------------------------------------------------------------------------HITCH PLATE HEIGHT MEASUREMENT 9” - Park towing vehicle on a level, hard surface and set parking brake. Hitch Plate Height Measurement - Measure from the ground to the bottom of the rear hitch plate (A).
ASSEMBLY ================================================================================================ STEP 3 --------------------------------------------------------------------------------Using the rounded measurement from the previous step, determine the correct Clevis Assembly (68) mounting holes.
ASSEMBLY ================================================================================================ STEP 5 Note: Wheel assembly not shown for clarity. -------------------------------------Loosely add the Bolt (13) & Lock Nut (21) from PANEL 04 to the Height Adjustment Handle (2). 2 13 Pointing the Nut side out, slide the Height Adjustment Handle (2) into place against the Lower Pivot (43) side plate. 21 Use the head of Bolt 13 to hold in place. 2 21 TIGHTEN HARDWARE SECURELY.
ASSEMBLY ================================================================================================ STEP 7 ------------------------------------------Attach Lock Arm (1) to Height Adjustment Handle (2) using the hardware in PANEL 06 in the order listed below: • • • • • • 26 9 5/16” x 1 1/4” Carriage Bolt (9) Height Adjustment Handle (2) Lock Arm (1) Large Washer (34) 5/16” Star Lock Washer (28) 5/16” Knob (31) 2 34 Note: For proper function of the sweeper height adjustment mechanism, it is impor
ASSEMBLY ================================================================================================ STEP 9 -------------------------------------------- 66 69 Assemble the hamper frame by inserting the first Rear Tube (66) into the Lower Tubes (69). LAY THESE TUBES IN THE BOTTOM OF THE HAMPER (40), ALONG THE INSIDE EDGE. 69 40 NOTE: Tubes (69) and (38) are easy to confuse. The differences are illustrated here.
ASSEMBLY ================================================================================================ STEP 10 ------------------------------------------Using the hardware in PANEL 10, assemble one 3/8” Nut (17) on each end of the Hamper Stop Rod (67) until it is approximately in the center of the threads. 40 38 67 17 22 69 Assemble each end of the Hamper Stop Rod (67) through the holes on the front of the Upper Side Tubes (38) and Lower Side Tubes (69).
ASSEMBLY ================================================================================================ STEP 13 --------------------------------------------------------------------------------- Locate and align the holes in the Upper Rear Tube (66) with the Side Tubes (38). 38 66 70 38 69 Locate and align the holes in the Lower Rear Tube (66) with the Bottom Tube (69). ! 67 WEAR EYE PROTECTION (SAFETY GLASSES) AND GLOVES WHILE EXECUTING THIS STEP. The spring rod requires some force to install.
ASSEMBLY ================================================================================================ STEP 14 ------------------------------------ Using the hardware in PANEL 11, assemble Hamper Mounts (5) to Upper Side Tubes (38) as shown here.
73 53 ASSEMBLY ================================================================================================ STEP 16 63 53 - - - - - - - - - - - - - - - - - - - - - - - - - To Sweeper Slacken Extend Pull Rope (37) to the back of the towing vehicle to an area that will be easily accessible from the towing vehicle seat. This is the area that the Pull Handle (35) will be attached. To Towing Vehicle 737 3 36 37 Allow the Pull Rope (37) to slacken several inches.
OPERATION ================================================================================================ CAUTION: AVOID INJURY! BEFORE ATTACHING OR REMOVING THE SWEEPER, MAKE SURE THE HAMPER IS EMPTY OF ALL MATERIAL. ATTACHING THE SWEEPER -------------------------------------------1. 2. 3. Park towing vehicle on a hard, level surface and set the parking brake. Align Clevis (68) with towing vehicle hitch plate.
OPERATION ================================================================================================ DETERMINING MAXIMUM TOWED WEIGHT --------------------------------------------------------------------------------CAUTION: Avoid injury! Excessive towed load can cause loss of traction and loss of control on slopes. Stopping distance increases with speed and weight of towed load. Total towed weight must not exceed combined weight of towing vehicle, ballast and operator.
OPERATION ================================================================================================ ADJUSTING THE BRUSH HEIGHT --------------------------------------------------------------------------------IMPORTANT: Setting the brush height too low for sweeping conditions causes excessive wheel skipping and slipping. For best performance, adjust brush height as high as possible for the material and conditions.
OPERATION ================================================================================================ LEVELING THE HAMPER --------------------------------------------After correct brush height is determined, it may be necessary to adjust the Hamper Stop (47) so that the Hamper assembly remains clear of the ground. TO ADJUST THE HAMPER STOP (47): 1. Loosen (but do not remove) the two Nuts (25) securing each side of the Hamper Stop (47).
OPERATION ================================================================================================ CAUTION: AVOID INJURY! Make sure area is clear of bystanders, especially children, before backing up. EMPTYING THE HAMPER ---------------------------------------Before dumping material from the Hamper: Park towing vehicle and set parking brake (see owners manual). TO EMPTY HAMPER: 1. 2. 3. 4. Tow the sweeper to a location the material should be dumped. Stop towing vehicle and set parking brake.
OPERATION ================================================================================================ STORAGE --------------------------------------------------------------------------------The sweeper can be tipped upright & stored against a wall using a minimum of space. 1. Remove any loose material from hamper, brushes, brush housing and drive assembly. The sweeper should be clean and dry before configuring for storage. 2.
MAINTENANCE ================================================================================================ IMPORTANT: Safety glasses should be worn while performing maintenance operations on the sweeper. Solvent proof gloves (rubber or latex), should be worn when using any cleaning or lubrication products. GENERAL PREVENTATIVE MAINTENANCE --------------------------------------------------------------------------------1. Do not allow material to remain in the Hamper for extended periods of time.
MAINTENANCE ================================================================================================ IMPORTANT: Safety glasses should be worn while performing maintenance operations on the sweeper. Solvent proof gloves (rubber or latex), should be worn when using any cleaning or lubrication products.
MAINTENANCE ================================================================================================ IMPORTANT: Safety glasses should be worn while performing maintenance operations on the sweeper. Solvent proof gloves (rubber or latex), should be worn when using any cleaning or lubrication products.
MAINTENANCE ================================================================================================ WHEEL AND DRIVE GEAR --------------------------------------------------------------------------------REF PART NO. DESCRIPTION QTY REF PART NO.
MAINTENANCE ================================================================================================ IMPORTANT: Safety glasses should be worn while performing maintenance operations on the sweeper. Solvent proof gloves (rubber or latex), should be worn when using any cleaning or lubrication products.
MAINTENANCE ================================================================================================ DUST COVER & BEARING RETAINER --------------------------------------------------------------------------------REF PART NO. DESCRIPTION QTY REF PART NO.
================================================================================================ MANUFACTURER’S LIMITED WARRANTY FOR BRINLY PULL-BEHIND ACCESSORIES The limited warranty set forth below is given by Brinly-Hardy Company with respect to new merchandise purchased and used in the United States, its possessions and territories. Hardy Co. During the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above.