Moderna Countertop Water Dispenser Setup Manual TM Model No.
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Contents. . . . . . . . . . . .
Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing, and operating the dispenser. WARNING: This product dispense water at very high temperatures. Failure to use properly can cause personal injury. When operating this dispenser, always exercise basic safety precautions, including the following: • Prior to use, this dispenser must be properly assembled and installed in accordance with this manual. • For indoor use only.
Intended Use This dispenser is intended to be used in household and similar applications such as: • Staff kitchen areas, offices, and other working environments • Farm houses • Hotels, motels, and bed-and-breakfast-type environments • Catering and other similar non-retail applications The dispenser is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerni
Product Features 1 6 7 8 2 4 5 9 10 11 12 3 Part 1 2 3 4 5 6 Description Part Touch panel Side filter panel Drip tray Water tap Fan Night light switch (blue) 7 8 9 10 11 12 Description Cold water switch (green) Hot water switch (red) Water drain with cover Water inlet with blue silicone plug Overflow outlet Power cord Specifications Model CLCTPOU820UVF2 Rated Voltage / Rated Frequency 115 V / 60 Hz Rated Power 520 W Heating Power 420 W Cooling Current 1.
How to Use Quick-Connect Tubing For ease of installation, the dispenser includes quick-connect tubing. Review the following instructions before installing dispenser. 1. Cutting Tubing A. Use the included Tube Cutter (G) or a sharp knife to cut the end of the tubing. B. After cutting, ensure ends are straight and able to sit flush against the back of the fitting. C. Inspect ends for any nicks, scratches, or rough spots. Recut tubing if necessary. 2. Connecting Tubing A. Insert tubing into the collet.
C. Position the back and sides of the dispenser at least 4 inches (10 cm) from a walls to permit free air circulation between the walls and the water dispenser. 4 in. (10 cm) 4 in. (10 cm) 2. Connect to the Cold Water Supply CAUTION: DO NOT CONNECT THIS WATER LINE TO A HOT WATER SUPPLY LINE. The water supply to the unit MUST be from the COLD WATER LINE. Using HOT WATER will severely damage your filters. C A. Turn off and then disconect the current cold water supply line. B.
3. Flush Filters New filters must be flushed before first use. First, remove filters from dispenser. Remove Side Filter Panel. One at a time, rotate filter in a counterclockwise direction, then remove it. D A. Connect the filter to the Filter Housing (D) by inserting the filter and rotating clockwise until the BRIO logos on the filter and the Filter Housing (D) are aligned. B. Ensure both the cold water supply and the shutoff valve on the Shutoff Valve Tube (A) are in the OFF position.
A D. Flush the filter for a minimum of 5 minutes. The recommended rate is 1.5-3 gallons of water (about 10 minutes) or until the water is clear in appearance. B E. Turn off the cold water supply, then turn off the shutoff valve on the Shutoff Valve Tube (A). Disconnect the tubing from the Filter Housing (D) and repeat the process with the remaining filter. After filters are flushed, reinstall them in the dispenser by rotating clockwise. 4. Complete Installation A.
E. Press either the Hot, Ambient, or Cold button on the Touch Panel until water is flowing steadily, and any air is removed from the tanks. F. Turn on the green Cold Water Switch (7) and red Hot-Water Switch (8) on back of the dispenser. NOTE: It takes approximately 15 minutes for the cold water to reach its optimal temperature and approximately 90 minutes for the hot water to reach its optimal temperature. Using the Dispenser Touch Panel Description 2 1. Up arrow – used to set time and temperature.
3. Adjusting Hot Water Temperature A. Simultaneously press the Unlock and Hot Water buttons for 3 seconds. The digital screen will flash, displaying the current hot water temperature. B. Using the Up or Down Arrows, adjust to the desired temperature. Temperature adjusts by 2-degree increments. Adjustable range is 174 °F to 194 °F (79 °C to 90 °C). NOTE: Hot water temperature is measured inside hot reservoir tank.
Cleaning and Maintenance • Keep dispenser in a cool, dry place and out of direct sunlight. • Ensure all sides of dispenser are at least 4 in. (10 cm) from walls. • Wipe the surfaces clean with a clean, moist cloth. NEVER immerse the dispenser in water or clean with a solvent. • Never place dispenser on paper or foam, which may store moisture and cause creepage. Never place anything flammable near the dispenser.
Remove the silicone plug and re-attach it to the filter door. The dispenser is now ready to use. NOTE: If the digital screen displays “loop” for more than 15 seconds without any operation, the dispenser will return to the normal state. If you wish to exit the sanitation process before it has ended, press the Cold button for 3 seconds to return to a standby state. Troubleshooting Problem Cause Solution • Plug in dispenser.
Warranty Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in the Product shall be free from defects in material and workmanship.
Contact Us Call: +1 844-257-4103 ©2022 Brio Water Technology, Inc.
