Point of Use Water Dispenser Setup Manual Model No.
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Features . . . . .
Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing and operating the dispenser. WARNING: This product dispenses water at very high temperatures. Failure to use properly can cause personal injury. When operating this dispenser, always exercise basic safety precautions, including the following: • Prior to use, this dispenser must be properly assembled and installed in accordance with this manual. • For indoor use only.
Intended Use This appliance is intended to be used in household and similar applications such as: • Staff kitchen areas in shops, offices and other working environments • Farm houses • Hotels, motels and other residential-type environments • Bed-and-breakfast environments • Catering and similar non-retail applications This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given s
Indicator Panel Description 1. Power/self-cleaning UV indicator light – When illuminated, indicates the dispenser is on. When blinking, indicates the self-cleaning UV process is on. 2. Hot water indicator light – When illuminated, indicates that the dispenser is heating water. 3. Cold water indicator light – When illuminated, indicates that the dispenser is cooling water. 4. Filter indicator light – When blinking, indicates filters need to be replaced soon.
Installation 1. Determine Installation Location A. Place the dispenser upright. B. Locate the dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet. NOTICE: Do NOT plug in the power cord until the entire installation section is completed. C. Position the back of the dispenser no closer than 20 cm (8 in.) from a wall and permit free airflow between the wall and water dispenser. 2.
E. Gently tug on the tube (B) to ensure a secure connection with the feed water adapter (H). H B 3. Flush the Filters IMPORTANT: Follow this procedure every time you replace your filters. IMPORTANT: Ensure the water supply is off before you begin. A. Connect a filter (D) to the filter housing (C) by twisting the filter (D) clockwise. C D B. Connect the tip of the shut-off valve tube (B) to the left side of the filter housing (C). C B C.
4. Install the Filters and Complete the Installation A. After flushing, twist each filter (D-G) clockwise into the filter housings located inside the dispenser cabinet. The sediment filter (D) goes on the left, followed by the pre carbon filter, the ultrafiltration filter, and finally, the post carbon filter. D B. Remove the safety plug from the water inlet hole on the back of the dispenser by pushing in the inlet hole collar and then gently pulling out the plug. C.
Operation IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water prior to drinking any water. Turn the Dispenser On/Off IMPORTANT: Before you activate the hot and cold switches, ensure water has filled the tanks inside the dispenser in order to prevent dry heating. 1. Plug in the dispenser. 2.
Troubleshooting Problem Solution • It takes up to one hour after setup to dispense cold water. • Make sure the power cord is properly connected to a working outlet. The cold water is not cold. • Make sure the back of the dispenser is at least 20 cm from a wall and there is free airflow on all 20 cm sides of the dispenser. • Make sure green power switch on back of dispenser is On. • If water still isn’t cold, call customer service at +1 844-257-4103 for assistance.
Clean the Dispenser CAUTION: Before cleaning, make sure the power switch is in the O (off) position and unplug the water dispenser. IMPORTANT: This dispenser contains UV technology that will help keep your dispenser clean. However, if you do need to clean your dispenser for any reason, follow these steps: 1. Remove remaining water from reservoirs in the dispenser by dispensing from the hot and cold taps into a pitcher or bucket. 2. Remove the top cover (1), cold tank cover (2), and separator (3). 1 3.
Filter Replacement Schedule Filter Type Model No. Replacement Schedule Sediment NFMPP5M 6-12 months or 3,600 liters Pre Carbon NFMGAC 6-12 months or 3,600 liters Ultrafiltration NFMUF 6-12 months or 3,600 liters Post Carbon NFMCTO5MS4 6-12 months or 3,600 liters Function Performs coarse filtration of inlet water, removing sand, rust, dirt, and other suspended solids. Removes chlorine, and other unpleasant tastes and odors.
Care and Maintenance • Keep this dispenser in a dry and cool place and avoid direct sunshine. • Ensure the back of the dispenser is at least 20 cm (8 in.) away from the wall. • Never put the dispenser on paper or foam, which may store water and then cause creepage. Never put anything flammable beside this machine. • Do not use the dispenser outdoors or in a place that can be splashed by water.
Warranty Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in the Product shall be free from defects in material and workmanship.
Contact Us Call: +1 844-257-4103 ©2023 Brio Water Technology, Inc.
