Water Dispenser Installation and Operation Manual Model No.
Table of Contents Safety Information ������������������������������������������������������������������������������������������������������������������������������������� 3 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire manual before assembling, installing, and operating the dispenser. WARNING: This product dispenses water at very high temperatures. Failure to use properly can cause personal injury. When operating this dispenser, always exercise basic safety precautions, including the following: • Prior to use, this dispenser must be properly assembled and installed in accordance with this manual. • For indoor use only.
Intended Use This dispenser is intended to be used in household and similar applications such as: • Staff kitchen areas in shops, offices, and other working environments • Farm houses • Hotels, motels, and other types of residential environments • Bed-and-breakfast type environments • Catering and similar non-retail applications This dispenser is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have
Indicator Panel Description 1. Power/Self cleaning indicator – When illuminated, indicates that the dispenser is on. When blinking, indicates that the self-cleaning feature is operating. 2. Hot water indicator light – When illuminated, indicates that the dispenser is heating water. 1 2 3 4 3. Cold water indicator light – When illuminated, indicates that the dispenser is cooling water. 4.
Package Contents A D E F G B H C Part Description I Quantity Part Description A Filter flushing tube 1 G B Shut-off valve tube (7 ft) 1 H 1 1 1 1 C D E F Filter housing (for filter flushing) Sediment filter Carbon filter RO (reverse osmosis) filter J K Quantity Post carbon filter Feed water adapter (with extra nut) 1 I Plumber’s tape 1 J K Drain saddle with foam gasket RO water-outlet tube 1 1 1 Materials Needed Wrench Electric drill with 1/4 in.
2. Connect to the Cold Water Supply CAUTION: DO NOT CONNECT THIS WATER LINE TO A HOT WATER SUPPLY LINE. The water supply to the unit MUST be from the COLD WATER LINE. Using HOT WATER will severely damage your filters. A. Turn off and then disconnect the current cold water supply line. H B. Connect the feed water adapter (H) to the cold water supply line. C. Connect the cold water supply line on top of the feed water adapter (H).
3. Make the Reverse Osmosis (RO) Waste Connections A. The RO filter assembly requires a drain line connection to be installed, which removes rejected water to the sewer. The drain saddle connects the drain line from the dispenser to your drain pipe. The drain saddle is designed to fit around a standard 1.5 in. OD (outer diameter) drain pipe. Always install the drain saddle before the P-trap and on a straight vertical or horizontal section of the pipe.
4. Flush the Filters IMPORTANT: Follow this procedure for every filter during installation and every time you replace your filters. IMPORTANT: Ensure the water supply is off before you begin. A. Connect a filter (D) to the filter housing (C) by twisting the filter (D) clockwise. C D B. Connect the tip of the shut-off valve tube (B) to the left side of the filter housing (C). C C.
5. Install the Filters and Complete the Installation A. After flushing, twist each filter clockwise into the filter housings located inside the dispenser cabinet. The sediment filter (D) goes on the left, followed by the carbon block filter (E), the RO filter (F), and the post carbon filter (G). D B. Remove the safety plug from the RO water outlet hole on the back of the dispenser by pushing in the inlet hole collar and then gently pulling out the plug. C.
Operation IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines. Dispense and dispose of at least 1 quart of water prior to drinking any water. Turn the Dispenser On/Off IMPORTANT: Before you activate the red hot-water and green cold-water switches, ensure water has filled the tanks inside the dispenser in order to prevent dry heating. 1. Plug in the dispenser. 2.
Troubleshooting Guide Refer to the table below for possible problems and their solutions. Problem Solution • It takes approximately 1 hour after setup to dispense cold water. • Make sure the power cord is properly connected to a working outlet. The cold water is not cold. • Make sure the back of the dispenser is at least 8 in. (20 cm) from a wall and there is free airflow on all 8 in. (20 cm) sides of the dispenser. • Make sure the green cold-water switch on the back of the unit is in the On position.
Cleaning and Maintenance This dispenser runs on a continuous UV cleaning cycle. It works for 40 minutes (UV indicator light is on), turns off for 140 minutes, and then cycles back on again as long as the dispenser is plugged in and turned on. CAUTION: Before manual cleaning, always turn off hot- and cold-water switches, and unplug dispenser. IMPORTANT: This dispenser contains UV technology that will help keep your dispenser clean.
Filter Type Replacement Schedule Sediment 6 months or 950 gallons (3596 liters) Carbon Block Reverse Osmosis (RO) Post Carbon Function Performs a coarse filtration of original water. Removes mud, sand, iron, rust, suspensions, and impurities. 6 months or 950 gallons (3596 liters) Reduces chlorine taste and odor, lead, and cysts. Removes up to 99% of contaminants including 12 months or 1,900 gallons (7192 liters) arsenic, lead, fluoride, heavy metals and more.
Temperature 33–100 °F Temperature 33–100 °F Care and Maintenance • Keep this dispenser in a dry and cool place and avoid direct sunshine. • Ensure the back of the dispenser is at least 20 cm (8 in.) away from the wall. • Never put the dispenser on paper or foam, which may store water and then cause creepage. Never put anything flammable beside this machine. • Do not use the dispenser outdoors or in a place that can be splashed by water.
person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in the Product shall be free from defects in material and workmanship. This Limited Warranty shall be limited to repair or replacement of parts, which prove defective under normal use and service and which Vendor shall determine in its reasonable discretion upon examination to be defective.
Contact Us Call: +1 844-257-4103 ©2021 DTWUSA
