Point of Use Water Dispenser Setup Manual Model No.
Table of Contents Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Intended Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Features . . . . .
Safety Information WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing and operating the dispenser. WARNING: This product dispenses water at very high temperatures. Failure to use properly can cause personal injury. When operating this dispenser, always exercise basic safety precautions, including the following: • Prior to use, this dispenser must be properly assembled and installed in accordance with this manual. • For indoor use only.
Product Features 1 10 12 11 2 13 4 3 14 5 6 7 15 8 16 9 1 2 3 4 5 6 7 8 Part Description Part Touch panel display Water tap Drip tray Filter cabinet Sediment filter Carbon block filter Reverse Osmosis (RO) filter Post carbon filter 9 10 11 12 13 14 15 16 Description RO pump Filter reset switch Cold water switch Hot water switch Condenser Drain outlet RO water inlet Water outlet Product Dimensions Height Width Depth 104.4 cm (41.1 in.) 31.1 cm (12.2 in.) 35.4 cm (14.0 in.
Touch Panel Description 1 1. Up arrow button – Press to set the time on the clock and increase temperature settings. 2 3 4 5 6 2. PCB indicator – Indicates the PP+C1+C2 filter lifetime. 3. RO indicator – Indicates the RO filter lifetime. 4. Clock/Temperature display – Shows the time and water temperature setting when setting the temperature of the hot or cold water. Also indicates when a water bottle needs to be replaced and when the dispenser is in self-cleaning mode. 7 8 9 10 5.
Installation 1. Determine Installation Location A. Place the dispenser upright. B. Locate the dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet. NOTICE: Do NOT plug in the power cord until the entire installation section is completed. C. Position the back of the dispenser no closer than 20 cm (8 in.) from a wall and permit free airflow between the wall and water dispenser. 2.
E. Gently tug on the tube (B) to ensure a secure connection with the feed water adapter (E). E B 3. Make the Reverse Osmosis Waste Connections The “RO” filter assembly requires a drain line connection to be installed, which removes rejected water to the sewer. The drain saddle connects the drain line from the dispenser to your drain pipe. The drain saddle is designed to fit around a standard 1.5 in. OD (outer diameter) drain pipe.
4. Flush the Filters IMPORTANT: Follow this procedure every time you replace your filters. IMPORTANT: Ensure the water supply is off before you begin. A. Connect a filter (D) to the filter housing (C) by twisting the filter (D) clockwise. C D B. Connect the tip of the shut-off valve tube (B) to the left side of the filter housing (C). C B C.
5. Install the Filters and Complete the Installation A. After flushing, twist each filter (D) clockwise into the filter housings located inside the dispenser cabinet. The sediment filter goes on the left, followed by the carbon, RO, and post carbon filter. D B. Remove the safety plug from the water inlet hole on the back of the dispenser by pushing in the inlet hole collar and then gently pulling out the plug. C. Connect the RO water outlet tube (H) from the RO drain saddle (G) to the RO water outlet.
Operation IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines. Dispense and dispose at least one quart of water prior to drinking any water. Turn the Dispenser On/Off IMPORTANT: Before you activate the hot and cold switches, ensure water has filled the tanks inside the dispenser in order to prevent dry heating. 1. Plug in the dispenser and turn the On/Off switch to On. 2.
Dispense Hot Water and Activate Child Safety Lock CAUTION: This unit dispenses water at temperatures that can cause severe burns. Avoid direct contact with hot water. Keep children and pets away from the unit while dispensing. Never allow children to dispense hot water without proper and direct supervision. Disable the heating feature by switching the heating convenience switch to the Off position.
Cleaning and Maintenance The UV icon on the upper-right corner of the display will begin blinking, indicating the cleaning process is underway. Care and Maintenance • Keep this dispenser in a dry and cool place and avoid direct sunshine. • Ensure the back of the dispenser is at least 20 cm (8 in.) away from the wall. • Never put the dispenser on paper or foam, which may store water and then cause creepage. Never put anything flammable beside this machine.
Filter Replacement Schedule Filter Type Replacement Schedule Sediment 6 months or 950 gallons Pre-Carbon 6 months or 950 gallons Reverse Osmosis (RO) 6 months or 1,900 gallons Post Carbon 6 months or 950 gallons Function Performs a coarse filtration of original water. Removes mud, sand, iron, rust, suspensions and impurities. Reduces chlorine, taste and odor, lead and cysts. Removes up to 99% of contaminants including arsenic, lead, fluoride, heavy metals and more. Taste and impurity removal.
Warranty Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in the Product shall be free from defects in material and workmanship.
Contact Us Call: +1 844-257-4103 ©2020 DTWUSA
