Product Manual

ManualsBrandsBriskHeat ManualsBucket, Drum + Tote HeatersPlastic Drum Heater — 5-Gallon, 150 Watt, 120 Volt

BriskHeat

Corporation/ Home of BriskHeat

Products

1055 Gibbard Ave, Columbus, OH 43201

Toll Free: 800-848-7673 Phone: 614-294-3376 Fax: 614-294-3807

Email: bhtsales1@briskheat.com

Web site: www.briskheat.com

PN:11663 Rev A

TROUBLESHOOTING GUIDE

Please read this guide prior to contacting BriskHeat

. This guide is designed to

answer the most commonly asked questions. If you are unable to identify the

problem or need additional assistance, please contact your local BriskHeat

distributor or contact us toll free (U.S. / Canada only) at 1-800-848-7673 or

614-294-3376 or bhtsales1@briskheat.com.

WARRANTY INFORMATION

BriskHeat

warrants to the original purchaser for the period of eighteen (18)

months from date of shipment or twelve (12) months from date of installation,

whichever comes ﬁ rst. Contact factory at 1-800-848-7673 (toll free, U.S. /

Canada) or 614-294-3376 for complete details.

PROBLEM SOLUTION(S)

Does not heat Verify heater is connected to proper voltage. The

identiﬁ cation label located on the power cord displays

the heater’s voltage requirement.

Check to see if there is a resistance reading (not an

open circuit) in heater using an ohm meter.

Circuit breaker is tripping Validate that the circuit breaker is capable of handling

the amp requirement of heater. The identiﬁ cation

label located on the power cord displays the heater’s

amperage requirement.

Examine heater and cord for any damage.

Does not ﬁ t Conﬁ rm that the heater provided was designed to ﬁ t

around your speciﬁ ed drum.

If the heater was designed for the speciﬁ ed drum,

please call 1-800-848-7673 or 614-294-3376 for further

assistance.

Something has lightly spilled on exterior

or interior

Apply any general household cleaner, that does not

contain any silicone rubber dissolving type

ingredients, with a clean cloth fabric.

Silicone Rubber Band

Drum / Pail Heaters

Instruction Manual

Read and understand this material before operating or

servicing this drum heater. Failure to understand how to safely

operate this heater could result in an accident causing serious

injury or death. This heater should only be operated by

qualiﬁ ed personnel.

DHCX series

DHCH series

DPCH series

ECONO series

DHCH, DHCS, DHCX, DHNH, DHNS, DHNX, DPCH,

DPCS, DPNH, DPNS, ECONO, and Custom Series

Summary of content (4 pages)

PAGE 1
Apply any general household cleaner, that does not contain any silicone rubber dissolving type ingredients, with a clean cloth fabric. If the heater was designed for the specified drum, please call 1-800-848-7673 or 614-294-3376 for further assistance. Confirm that the heater provided was designed to fit around your specified drum. Examine heater and cord for any damage. Validate that the circuit breaker is capable of handling the amp requirement of heater.
PAGE 2
Hazards or unsafe practices which COULD result in minor personal injury or property damage. Hazards or unsafe practices which COULD result in severe personal injury or death Immediate hazards which WILL result in severe personal injury or death The symbol above is used to call your attention to instructions concerning your personal safety. It points out important safety precautions.
PAGE 3
6 © BriskHeat® Corporation. Home of BriskHeat® Products. All rights reserved. NOTE: These heaters have a built-in, high limit thermostat that will prevent it from overheating. T-3 rated heaters: 292°F [145°C] high limit thermostat T-4A rated heaters: 158°F [70°C] high limit thermostat 3. Adjust the high and low temperature set-points to an appropriate level for the environment. The low temperature set-point is the process control.
PAGE 4
© BriskHeat® Corporation. Home of BriskHeat® Products. All rights reserved. 4. Confirm voltage / wattage rating of heater is appropriate for power supply device or temperature controller. The heater is designed to work at a specific voltage to heat properly. For additional information, contact your local distributor or BriskHeat®. 3. Check that the desired placement of the heater will not cause damage to the heater through impact shock, vibration, ambient temperature, or by neighboring moving parts.