Advocate 70 CS ® User Guide IMPORTANT: Thoroughly read and follow all instructions before installing this child seat. Store this user guide in the pocket behind the cover (See features pages for reference).
Table of Contents Safety Information .......................................................................................2 Warnings ...............................................................................................................2 Important Notes....................................................................................................4 Certification ...........................................................................................................5 Registration ...........
WARNING! Section Title DEATH or SERIOUS INJURY can occur: • Use only in a rear-facing position when using it with an infant weighing less than 20 lbs (9.1 kg) OR is less than 1 year of age. • Use only with children who weigh between 5 and 70 lbs (2.3 – 31.8 kg) and whose height is 49 in. (124.5 cm) or less. Use rearfacing for children who weigh between 5 and 40 lbs (2.3 – 18.1 kg). Use forward-facing for children who weigh between 20 and 70 lbs (9.1 – 31.8 kg) AND are at least 1 year of age.
Section Title • This child seat must not be used in the home, in boats, or other noncertified applications. • Based on crash statistics, the National Highway Traffic Safety Administration (NHTSA) recommends that parents select the back seat as the safest location for a properly installed child seat. Please study Vehicle Seating Positions on page 13 to ensure your child’s safety and consult your vehicle owner’s manual. • Secure this child seat even when it is not occupied.
Safety Information Important Notes • Verify that the child seat is securely installed and the harness is properly adjusted around the child each time the child seat is used. • Discontinue use of this child seat if it has been in a moderate or severe crash. It is not necessary to replace a car seat after a minor crash defined by the U.S. National Highway Traffic Safety Administration (NHTSA) as: * The vehicle is driveable from the crash site. * The vehicle door nearest the child seat was not damaged.
Safety Information Certification This child restraint system conforms to all applicable Federal Motor Vehicle Safety Standards. This Restraint is Certified For Use in Motor Vehicles and Aircraft. Registration Child restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall. Send your name, address, e-mail address if available and the restraint’s model number and manufacturing date to Britax Child Safety, Inc. P.O.
Safety Information Important Child Seat Usage Information All infants must ride rear-facing at least until they have reached 1 year of age and weigh 20 lbs (9.1 kg). An infant positioning insert may be necessary for small infants to achieve a snug fit if the child is under 12 lbs and the lowest harness slots fall above the infants shoulders. The Infant positioning insert is sold separately at select retailers and on www.britaxusa.com.
Safety Information Forward-Facing: 20 – 70 lbs (9.1 – 31.8 kg) and at least 1 year of age WARNING! FORWARD-FACING use of this child seat is ONLY for children who meet ALL of the requirements below. If the child cannot be secured within these requirements because they are too large, another type of child seat (such as a booster) may be required. If the child cannot be secured within these requirements because the child is too small, review the rear-facing information on page 6.
Vehicle Compatibility Compatible Vehicle Seat Belts NOTE: The information in this section only applies to installation with vehicle seat belts. Vehicle seats and seat belts differ from vehicle to vehicle. Refer to your vehicle owner’s manual for specific information about your vehicle seat belts and their use with child seats. Lap-Shoulder (3-Point) Belt 1. ALR (Automatic Locking Retractor) with Sliding Latch Plate a Has a latch plate that freely slides along the vehicle seat belt webbing.
Vehicle Compatibility 2. ELR (Emergency Locking Retractor) with Locking Latch Plate a Has a latch plate that locks the vehicle belt. * This type of latch plate locks the vehicle belt when the vehicle belt and latch plate lie flat. When using this type of vehicle belt with a child seat, ensure the latch plat and vehicle belt lie flat against the child seat or the vehicle belt may remain unlocked. b Latch plate Has a retractor that locks only in an emergency situation such as sudden stop or crash. 3.
Vehicle Compatibility 4. ELR (Emergency Locking Retractor) with a Sliding Latch Plate a b Has a latch plate that freely slides along the vehicle seat belt webbing. Has a retractor that locks only in an emergency situation such as sudden stop or crash. IMPORTANT: This belt type requires the use of the lock-offs built into the seat for rear- and forward-facing installations. See page 21 for information on using the lock-offs. Lap Belt 5.
Vehicle Compatibility c Tightens by feeding the belt webbing back into the retractor. 6. Locking Latch Plate a Has a latch plate that prevents the webbing from becoming loose. Latch plate b Tightens by pulling on the belt webbing.
Vehicle Compatibility Incompatible Vehicle Seat Belts WARNING! The following types of vehicle seat belts are NOT compatible with this child seat. If any of the belt types listed below are in the chosen seating position, choose another vehicle seating position or check your vehicle owner’s manual for information on installing a car seat in your vehicle.
Vehicle Compatibility Vehicle Seating Positions WARNING! DO NOT place child seat rear-facing in the front seat of a vehicle with a passenger air bag unless deactivated. DEATH or SERIOUS INJURY can occur. See your vehicle owner’s manual for child seat installation instructions. The back seat is the safest place for children 12 and under. Some vehicles have no seating positions which are compatible with this child seat. If in doubt, contact the vehicle manufacturer for assistance.
Child Seat Features 1 2 3 4 13 14 5 6 15 16 17 18 19 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 14 Cover Harness Height Adjuster Head Restraint Comfort Pads Infant Body Pillow Harness Holder Lower Connector Bar Lower Connector Strap (LATCH component) Lower Connector Adjuster Release Button (LATCH component) 20 21 10 Lower Connector Adjuster (LATCH component) 11 Lower Connector Release Button (LATCH component) 12 Lower Connector (LATCH component) 13 User Guide Storage (in pocket behind cover) 14 HUGS™ (Harne
Child Seat Features 1 31 22 23 24 25 26 27 28 29 32 33 7 34 30 35 17 Belly Pad 18 Harness Adjuster Lever (under cover) 19 Click & Safe™ Snug Harness Indicator (under cover) 20 Harness Adjuster Strap 21 Recline Adjustment Handle 22 Serial Number & Manufactured Date Label 23 Shell 24 Side Impact Cushion 25 Harness Slots 26 Forward-Facing Belt Slot 27 Forward-Facing Lock-Offs (Red – under cover on front of shell) 28 Rear-Facing Lock-Offs (Blue – under cover on front of shell) 29 Rear-Facing Belt Slot
Child Seat Functions Click & Safe™ Snug Harness Indicator ImpoRtANt: See pages 55 – 57 for detailed instructions on securing your child. The Click & Safe is an audible indicator to help determine when the child seat harness is within range of appropriate snugness. The Click & Safe is a secondary feature. Parents should be aware of what amount of snugness is appropriate in the harness. The harness should have a comfortable but snug fit around the child. A snug strap should not allow any slack.
Child Seat Functions 3 4 5 Remove slack in the harness from around child’s upper thighs. Remove slack in the harness between the HUGS™ chest pads and buckle. Pull the harness adjuster strap up and away from the child seat until a click is heard. The Click & Safe™ indicator will click when the harness is within range of appropriate snugness. Checklist 9 Check that the harness is buckled and secure. 9 Check that the harness is snug and you can not pinch excess.
Child Seat Functions Harness Height Adjustment 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 1b 1a 2 Squeeze the harness height adjuster, slide the harness into the desired position and release. * Ensure the harness has locked into position. NOTE: In rear-facing mode, always position the harness straps at or below your child’s shoulders. See page 6. In forward-facing mode, always position the harness straps at or above your child’s shoulders. See page 7.
Child Seat Functions Adjusting Buckle Position ImpoRtANt: • ALWAYS position the buckle in the ADJUSTMENT inner slot for rear-facing use. SLOT • The vehicle belt must pass in front of the buckle strap for rear-facing use. • NEVER leave the buckle in the adjustment slot. • Use the outer buckle slot when installing the child seat forwardfacing with a child weighing 30 lbs (13.6 kg) and above or if the buckle is under the child in the inner position. 1 Unbuckle the harness.
Child Seat Functions Fastening the Buckle Releasing the Buckle Insert one tongue at a time into the buckle. Press the release button and pull the tongues from the buckle. NOTE: Proper connection is confirmed with a click after inserting each buckle tongue. NOTE: Periodically clean the buckle to ensure proper operation. See Page 64. Using the Chest Clip 1 20 Open the chest clip. a Press tabs b Pull apart Push together to fasten. 2 NOTE: Always position the chest clip at armpit level.
Child Seat Functions Using the Lock-Offs IMPORTANT: Both parts of the lock-off must be opened to secure a vehicle belt. To Open: LOCKING TAB To Close: 1 2 VEHICLE BELT LOCKING TAB CLAMP 2 CLAMP 1 Open the locking tab 2 Open the clamp 1 1 Close the clamp over the vehicle belt 2 Slide your palm or thumb along the locking tab until a click is heard Infant Body Pillow The infant body pillow is designed to provide better fit and comfort for infants using this child seat.
Child Seat Functions Recline Positions This child seat has 3 positions. To adjust, pull the recline handle then rotate the child seat shell into the desired position. Release the recline handle, then verify the child seat has locked into position. NOTE: Set the recline position BEFORE installing.
Child Seat Functions Forward-Facing IMPORTANT: In forward-facing installations, it is important that the base of the child seat rests completely flat on the vehicle seat. As illustrated below, it is permissible to allow up to 20% or 3 inches (7.6 cm) of the base to hang over the edge of the vehicle seat. Some vehicle seats do not allow enough of the child seat base to contact the vehicle seat. If this is the case, adjust the recline angle to a more upright position.
Child Seat Functions Using Lower Anchors and Tethers for Children (LATCH) Lower Anchors and Tethers for Children or LATCH, is a system available on this child seat that offers an alternative to vehicle seat belt installation methods. See pages 14 and 15 for LATCH components on this child seat. LATCH SYSTEM ANCHOR LOCATIONS Lower Anchors Tether Anchor Lower Anchors The figure above shows typical locations for lower anchors and tether anchors in a vehicle.
Child Seat Functions Using the Lower Connectors Where to find the Lower Connectors The lower connectors are located in the back of the base of the child seat. Store the connectors in the slots when not in use. To remove the lower connector from the storage slot or lower anchor: 1 Press and hold the red release button. 2 Pull the lower connector from the storage slot or lower anchor.
Child Seat Functions Using the Versa-Tether® WARNING: Failure to follow the guidelines below may cause the child seat not to perform as intended: • Attach the Versa-Tether only to tether anchors identified by your vehicle manufacturer as tether anchorage points. Only use the designated tether anchor for each seating position. • If your vehicle does not currently have a tether anchor attachment, refer to your vehicle owner’s manual or contact your vehicle manufacturer for assistance.
Child Seat Functions OR OR Rear-Facing Rear-Facing Forward-Facing Rear-Facing Tether Connector Strap Because every vehicle model is different, a location to anchor the tether for rear-facing installations may vary. Use the rear-facing tether connector strap to assist in creating an anchor point. 1 Find a fixed location in the vehicle that is bolted to the floor. * If you cannot find a location to create an anchor point, contact the vehicle manufacturer to identify a tether connection point.
Child Seat Functions IMPORTANT: The Versa-Tether® carry clip is only for use when you wish to carry the child seat between locations. Do not install the child seat with the VersaTether attached to the carry clip. Secure the excess Versa-Tether webbing in the elastic strap during use. Store the Versa-Tether in the storage pouch when not in use. Always ensure any excess webbing is contained within your vehicle.
Child Seat Functions The Versa-Tether can indicate when the child seat has been in a moderate or severe crash (see page 4) and replacement of the child seat is necessary. Figure 1 shows a tether acceptable for continued use (provided the child seat has not been involved in a crash). The colored stitching will be intact but not visible from the back of the seat. Figures 2 and 3 show examples of when the tether has been damaged and is unacceptable for continued use.
Rear-Facing Installation LATCH Installation Before You Begin: • Check that your vehicle has lower anchors. * Refer to your vehicle owner’s manual or contact the vehicle manufacturer for the maximum weight rating for their lower anchors. Use vehicle belt (not lower connectors) for installations with children who weigh more than the vehicle lower anchor limit. Unless specified otherwise by the vehicle manufacturer, assume a 40 pound (18.1 kg) child is the vehicle lower anchor limit.
Rear-Facing Installation Install with LATCH as shown above. ImpoRtANt: The buckle should be in the inner slot for rear-facing installation.
Rear-Facing Installation 1 Firmly press the lower connectors onto the adjacent lower anchors. • A click confirms attachment. • Verify that the lower connector strap is not twisted. TIP: You may need to turn the front of the child seat toward you for easier access to the lower anchors. NOTE: If a click is not heard when connecting either lower connector, the lower connector strap may be twisted, or there may be debris in the lower connector.
Rear-Facing Installation Check that the child seat is reclined to position 3 Check that there is LESS than 1 in. (2.5 cm) of movement (front to back or side to side) at the belt path Check lower connector attachments Checklist 9 Check that all connections are secure. 9 Check that the lower connector straps are not twisted. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path.
Rear-Facing Installation Lap-Shoulder Belt Installation Before You Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. * If your vehicle seat belt system includes a locking feature, use of the lock-offs is not required as long as the vehicle seat belt system is locked. Check your vehicle owner’s manual to determine how to lock your vehicle seat belt system when installing a child restraint.
Rear-Facing Installation Install with lap-shoulder belt as shown above. ImpoRtANt: • The harness buckle strap should lie toward the back of the child seat during installation. • The buckle should be in the inner slot for rear-facing installation.
Rear-Facing Installation 1 2 3 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 1b Remove the body pillow, unbuckle the harness, and remove the belly pad. Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear-facing belt path. 1a 4b IMPORTANT: Ensure buckle is in inner slot and lying away from the belt path. 4 Open the blue lock-off closest to where the vehicle belt will be buckled.
Rear-Facing Installation 8 Rear-facing installations can be improved by the use of the VersaTether (see pages 26 – 29). 9 Pull the buckle up through its appropriate slot in the cover. 10 Replace the cover and the belly pad. Check that the child seat is reclined to position 3 Check that there is LESS than 1 in. (2.5 cm) of movement (front to back or side to side) at the belt path Check buckle connection Checklist 9 Check that the vehicle belt is securely fastened.
Rear-Facing Installation Lap Belt Installation Before You Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. • This child seat must be reclined to position 3 and placed rear-facing on the vehicle seat.
Rear-Facing Installation Install with lap belt as shown above. ImpoRtANt: • The harness buckle strap should lie toward the back of the child seat during installation. • DO NOT use lock-offs for lap belt installations. • The buckle should be in the inner slot for rear-facing installation.
Rear-Facing Installation 1 2 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward Remove the body pillow, unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear-facing belt path. 4 Route the vehicle seat belt through the rear-facing belt slots, then buckle. Ensure the vehicle belt is not twisted.
Rear-Facing Installation Check that the child seat is reclined to position 3 Check that there is LESS than 1 in. (2.5 cm) of movement (front to back or side to side) at the belt path Check buckle connection Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location.
Forward-Facing Installation LATCH Installation Before You Begin: • Check that your vehicle has lower anchors. * Refer to your vehicle owner’s manual or contact the vehicle manufacturer for the maximum weight rating for their lower anchors. Use vehicle belt (not lower connectors) for installations with children who weigh more than the vehicle lower anchor limit. Unless specified otherwise by the vehicle manufacturer, assume a 40 pound (18.1 kg) child is the vehicle lower anchor limit.
Forward-Facing Installation Install with LATCH as shown above. WARNING! • Your child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat. • This child seat must not be used forward-facing for children less than one year of age OR who weigh less than 20 lbs (9.1 kg). • Some vehicle head restraints may obstruct the harness adjuster from reaching the highest position. If this is the case, you may need to raise or remove the vehicle head restraint.
Forward-Facing Installation 1 Firmly press the lower connectors onto the adjacent lower anchors. • A click confirms attachment. • Verify that the lower connector strap is not twisted. TIP: You may need to turn the back of the child seat toward you for easier access to the vehicle lower anchors. 1 2 NOTE: If a click is not heard when connecting either lower connector, the lower connector strap may be twisted, or there may be debris in the lower connector.
Forward-Facing Installation Check Versa-Tether® (Top Tether) attachment Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat Check that there is LESS than 1 in. (2.5 cm) of movement (front to back or side to side) at the belt path Check that Versa-Tether® (Top Tether) webbing is stored in the elastic strap Check lower connector attachments Checklist 9 Check that all connections are secure. 9 Check that the lower connector straps are not twisted.
Forward-Facing Installation Lap-Shoulder Belt Installation Before You Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. * If your vehicle seat belt system includes a locking feature, use of the lock-offs is not required as long as the vehicle seat belt system is locked. Check your vehicle owner’s manual to determine how to lock your vehicle seat belt system when installing a child restraint.
Forward-Facing Installation Install with lap-shoulder belt as shown above. WARNING! • Your child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat. • This child seat must not be used forward-facing for children less than one year of age OR who weigh less than 20 lbs (9.1 kg). • Some vehicle head restraints may obstruct the harness adjuster from reaching the highest position. If this is the case, you may need to raise or remove the vehicle head restraint.
Forward-Facing Installation 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 3 4 Remove the body pillow and unbuckle the harness. Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. Open the red lock-off closest to where the vehicle belt will be buckled. a Open the locking tab b Open the clamp 5 6 Route the vehicle belt through the forward-facing belt slots, then buckle.
Forward-Facing Installation Attach and remove the slack from the Versa-Tether (if an anchor point is available). 9 Store the excess webbing in the elastic strap. 10 Replace the cover. 8 Check Versa-Tether® (Top Tether) attachment Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat Check that there is LESS than 1 in. (2.
Forward-Facing Installation Lap Belt Installation Before You Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. • Remove the Versa-Tether from the pouch and place it up and over the child seat back. * Britax recommends that the Versa-Tether is used at all times. Using the tether will improve the stability of the child seat and reduce the risk of injury. Check your vehicle owner’s manual for tether anchor locations.
Forward-Facing Installation Install with lap belt as shown above. WARNING! • DO NOT use lock-offs for lap belt only installations. • Your child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat. • This child seat must not be used forward-facing for children less than one year of age OR who weigh less than 20 lbs (9.1 kg). • Some vehicle head restraints may obstruct the harness adjuster from reaching the highest position.
Forward-Facing Installation 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow and unbuckle the harness. 3 Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. 4 Route the vehicle seat belt through the forward-facing belt slots, then buckle. Ensure the vehicle belt is not twisted.
Forward-Facing Installation Check Versa-Tether® (Top Tether) attachment Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat Check that there is LESS than 1 in. (2.5 cm) of movement (front to back or side to side) at the belt path Check that Versa-Tether® (Top Tether) webbing is stored in the elastic strap Check buckle connection Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that no more than 20% or 3 inches (7.
Aircraft Installation This child seat is certified for aircraft use. Most airlines in the U.S. and Canada will allow the use of a child seat as long as it is labeled as an approved child seat for use in aircraft and fits properly on the aircraft seat. Contact the airline about their policy prior to traveling. The FAA recommends that a child weighing up to 40 lbs (18.1 kg) use a certified, harnessed child seat while traveling on an aircraft.
Securing Your Child WARNING! • Adjust the belts provided with this child seat so they fit snugly around your child. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position. • Adjust the harness to fit the clothes the child is wearing. Remove bulky coats and/or jackets before putting the child in the child seat.
Securing Your Child 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 1b 1a 2 Open the chest clip. a Press tabs b Pull apart 2b 2a 3 4 Release the buckle and attach the harness straps to the harness holders. Place the child in the child seat. * Ensure the child is positioned upright in the child seat and not slouching. Their bottom must touch the child seat, and their back must rest flat against the back of the child seat.
Securing Your Child 6 Fasten the harness buckle. 6 * Proper connection is confirmed with a click after inserting each buckle tongue. 7 8 Pull the excess slack up to the child’s shoulder area while moving the HUGS™ chest pads down toward the buckle. Pull the harness adjuster strap up and away from the child seat to tighten the harness. The Click & Safe™ indicator will click when the harness is within the range of appropriate snugness.
Care and Maintenance Cover Removal WARNING! • Never remove the buckle tongues from the harness. They cannot be reattached after removal. If reassembled incorrectly, the child seat may not perform as intended. • DO NOT remove the HUGS™ chest pads from the harness straps. 1 Loosen the harness. a Lift release lever b Pull both harness straps forward 1b 1a 2 Open the chest clip. a Press tabs b Pull apart 3 Unbuckle the harness.
Care and Maintenance 6 7 8 9 Raise the harness to the highest position and detach the hook and loop fasteners on the head restraint cover from around the harness. Detach the hook and loop fasteners on the head restraint cover from around the head restraint. Detach the elastic straps from the tabs behind the harness adjustment handle. Remove the head restraint cover. 6 8 10 Detach the plastic hooks from the bottom edge of the child seat. 10 11 Adjust the harness to the lowest position.
Care and Maintenance 13 Pull the buckle through the slot in the cover. 14 Pull the cover fabric from between the Side Impact Cushion and child seat shell. 14 15 Remove the cover from the child seat shell.
Care and Maintenance Cleaning the Cover • HAND WASH the cover using cold water and mild soap. • LINE DRY to prevent the cover from shrinking. • DO NOT: * * * * Bleach Machine wash Machine dry Iron Cleaning the Harness • SPONGE CLEAN the harness using warm water and mild soap. • TOWEL DRY • DO NOT: * * * * * Disassemble the harness Bleach Machine wash Machine dry Iron Cleaning the Shell • SPONGE CLEAN the shell using warm water and mild soap.
Care and Maintenance Cover Replacement 1 Fit the child seat cover around the child seat shell. 1 2 Pull the cover fabric tight and slide it between the child seat shell and Side Impact Cushion. 2 3 Attach the plastic hooks on the cover to the back of the child seat shell. 4 Attach the plastic hooks to the bottom edge of the child seat.
Care and Maintenance 5 Pull the buckle through the slot in the cover. * Ensure that the buckle is through the correct cover slot for the buckle position. 6 7 8 9 Fit the head restraint cover around the harness adjustment handle and attach the elastic straps to the tabs behind the harness adjustment handle. Attach the hook and loop fasteners on the head restraint cover around the head restraint. Attach the hook and loop fasteners on the head restraint cover around the harness.
Care and Maintenance Cleaning the Buckle If your child eats and drinks while in the child seat, you will need to check the buckle periodically and rinse out any accumulated debris. Remove the Buckle 1 Unbuckle the harness. Remove the belly pad and pull the buckle through the cover. 2 Turn the buckle webbing and slide it between buckle positions.
Care and Maintenance 3 Guide the buckle retainer up through the slot in the child seat shell to remove. To Clean: • THOROUGHLY RINSE the buckle using warm water. • TEST THE BUCKLE by fastening and unfastening until a click is heard after inserting each buckle tongue. If clicks are not heard, repeat the cleaning procedure.
Care and Maintenance Re-thread the Buckle ImpoRtANt: • ALWAYS position the buckle in the ADJUSTMENT inner slot for rear-facing use. SLOT • The vehicle belt must pass in front of the buckle strap for rear-facing use. • NEVER leave the buckle in the adjustment slot. • Use the outer buckle slot when installing the child seat forwardfacing with a child weighing 30 lbs (13.6 kg) and above or if the buckle is under the child in the inner position.
Tips and Troubleshooting Troubleshooting Problem: The harness cannot be adjusted to its full height. Possible Solution: Check the seating position where the child seat is installed. The vehicle head restraint may obstruct the path of the child seat harness height adjuster. Remove or raise the vehicle head restraint and try adjusting the harness height again. Problem: The harness is hard to adjust. Possible Solution: The yoke may be caught on the Versa-Tether® webbing or other component of the child seat.
Warranty This child seat was manufactured by Britax Child Safety, Inc. Britax® warrants this product to the original retail purchaser as follows: LIMITED ONE-YEAR WARRANTY This product is warranted against defective materials or workmanship for one year from the date of original purchase. Proof of purchase is required. Your exclusive remedy for this warranty is that Britax will, at its option, provide repair or replacement components for this product.
69
Britax Child Safety, Inc. 13501 South Ridge Drive Charlotte, NC 28273 USA A Britax Childcare Group Limited company Tel. : 1-888-427-4829 www.Britax.
