Installation Sheet

ManualsBrandsBrizo ManualsBathroom FaucetsBrizo Atavis 1.2 GPM Widespread Bathroom Faucet with Pop-Up Drain Assembly Less Handles - Limited Lifetime Warranty

Para instalación fácil de su llave

Brizo

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

• Comprar las conexiones correctas para el

suministro de agua.

For easy installation of your Brizo

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

• To purchase the correct water supply hook-up.

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:

Pour installer votre robinet Brizo

facilement, vous devez:

• LIRE TOUTES les instructions avant de

débuter;

• LIRE TOUS les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien;

• Acheter le bon nécessaire de raccordement.

06/12/2018 Rev. A

www.brizo.com

TWO HANDLE WIDESPREAD BATHROOM FAUCET

DOS MANILLARES ANCHO GRIFO DE BAÑO

ROBINET DE SALLE DE BAINS À DEUX POIGNÉES

102232

▲Specify Finish / Especifíque el Acabado / Précisez le Fini

Model/Modelo/Modèle

65342LF-pLHP

Series/Series/Seria

ATAVIS

Summary of content (8 pages)

PAGE 1
02232 TWO HANDLE WIDESPREAD BATHROOM FAUCET DOS MANILLARES ANCHO GRIFO DE BAÑO Model/Modelo/Modèle 65342LF-pLHP Series/Series/Seria ROBINET DE SALLE DE BAINS À DEUX POIGNÉES ATAVISTM Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 2 1 1 1 1/8" (28.58 mm) 1 1/8" (28.58 mm) 2 3 2 3 INSTALLATION OF SPOUT INSTALLATION OF VALVE ASSEMBLIES NOTE: When drilling mounting holes for the spout, it is recommended that the hole size be 1 1/8" (29 mm). NOTE: When drilling holes for supply valves, it is recommended that the hole size be 1 1/8" (29 mm). Look for a blue label or dot on cold valve assembly and red label or dot on hot valve assembly and install them on appropriate side. Make sure gasket (1) is in place on bottom of spout.
PAGE 3
4 3 3 2 1 3 1 3 2 4 4 INSTALLATION OF HOSE ASSEMBLY INSTALLATION OF HANDLES Snap the quick connect hose assembly (1) onto the spout nipple (2) and end valve nipples (3). Pull down moderately to ensure each connection has been made. To remove hose, apply pressure to the base of the clip on both sides (4) and pull down on the hose. Do not disassemble the clips from the hose assembly. NOTE: Handles sold separately. Make sure valve cartridge is in off position.
PAGE 4
5 A. B. 2 1 1 2 2 1 1/2” (12.7 mm) IPS A. MAKE CONNECTIONS TO SUPPLY PLUMBING Connect flexible outlet hoses (1) to valve inlet ports (2) as shown. B. MAKE CONNECTIONS TO WATER LINES B. HAGA LAS CONEXIONES A LAS LÍNEAS DE AGUA B. RACCORDEZ LES TUYAUX D’EAU CHAUDE ET D’EAU FROIDE Tighten nuts firmly with a wrench, but do not over tighten. A.
PAGE 5
6 A. B. C. E. D. 1 1 2 3 2 3 1 2 1 1 G. F. 4 2 2 H. 5 4 3 2 1 1 2 5 3 2 6 POP-UP DRAIN INSTALLATION A. Remove stopper (1) and flange (2). B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down. C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece. D. Apply silicone to underside of flange (1). Insert body (2) into sink. Screw flange (1) into body (2). E. Pivot (1) must face faucet. Pull assembly (2) down firmly and hold in place.
PAGE 6
7 1 7 2 1 6 2 3 4 5 MAINTENANCE SHUT OFF WATER SUPPLIES BEFORE SERVICING FAUCET. If your faucet leaks out of spout outlet or around handle body, replace valve cartridge (4). a. Unscrew handle from escutcheon, pull up on handle (1) to remove. NOTE: It is best if you pull straight up on the handle. b. Remove screw (2) and spline adapter (3). c. Remove cartridge (4) by turning it counterclockwise with a 15MM hex socket wrench or available tool RP100224. d.
PAGE 7
Model/Modelo/Modèle 65342LF-pLHP Series/Series/Seria ATAVISTM RP100224 15MM Cartridge Service Tool Herramienta de servicio para el cartucho 15 MM Clé de 15 MM pour cartouche RP46409 Spline Adapter and Screw Adaptador con estrías y tornillo Adaptateur cannelé et vis RP48428-1.
PAGE 8
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.