Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysPhototransistor-Optocoupler SO 4 Half-pitch Type (misc.) AC-FotoTX-Coupler 1-Channel T/R

ACPL-214

AC Input, Half-Pitch Phototransistor Optocoupler

Data Sheet

Description

The ACPL-214 is an AC-input single channel half-pitch

phototransistor optocoupler which contains 2 light

emitting diodes connected inversely parallel & optically

coupled to a phototransistor. It is packaged in a 4-pin SO

package.

The input-output isolation voltage is rated at 3000 Vrms.

Response time, tr, is 2μs typically, while minimum CTR is

20% at input current of 5 mA

ACPL-214 pin layout

Features

• Current transfer ratio

(CTR: 20% (min) at I

= ±5mA, V

= 5V)

• High input-output isolation voltage

ISO

= 3,000V

RMS

)

• Non-saturated Response time

(tr: 2µs (typ) at V

= 10V, I

= 2mA, R

= 100W)

• SO package

• CMR 10kV/μs (typical)

• Safety and regulatory approvals

- UL

- CSA

- IEC/EN/DIN EN 60747-5-2

• Options available:

– CTR Ranks 0, A

Applications

• I/O Interface for Programmable controllers,

computers.

• Sequence controllers

• System appliances, measuring instruments

• Signal transmission between circuits of dierent

potentials and impedances.

Lead (Pb) Free

RoHS 6 fully

compliant

RoHS 6 fully compliant options available;

-xxxE denotes a lead-free product

1 2

4 3

1 2

4 3

• Pin 1 Anode

• Pin 2 Cathode

• Pin 3 Emitter

• Pin 4 Collector

Summary of content (7 pages)

PAGE 1
ACPL-214 AC Input, Half-Pitch Phototransistor Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features The ACPL-214 is an AC-input single channel half-pitch phototransistor optocoupler which contains 2 light emitting diodes connected inversely parallel & optically coupled to a phototransistor. It is packaged in a 4-pin SO package.
PAGE 2
Ordering Information ACPL-214-xxxx is pending UL Recognition with 3000 Vrms for 1 minute per UL1577 and is pending approval under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 3
Solder Reflow Temperature Profile 30 seconds Temperature (°C) 250 °C 260 °C (Peak Temperature) 217 °C 200 °C 2. When using another soldering method such as infrared ray lamp, the temperature may rise partially in the mold of the device. Keep the temperature on the package of the device within the condition of (1) above. 150 °C 25 °C 60 sec 60 ~ 150 sec 90 sec 1. One-time soldering reflow is recommended within the condition of temperature and time profile shown at right.
PAGE 4
Electrical Specifications Over recommended ambient temperature at 25ºC unless otherwise specified. Parameter Symbol Min. Typ. Max. Units Test Conditions Note Forward Voltage VF - 1.2 1.4 V IF = ±20mA Fig.6 Terminal Capacitance Ct - 60 - pF V = 0, f = 1MHz Collector Dark Current ICEO - - 100 nA VCE = 48V, IF = 0 mA Collector-Emitter Breakdown Voltage BVCEO 80 - - V IC = 0.
PAGE 5
60 160 40 Collector Power Dissipation, Pc(mW) Forward Current, I F (mA) 50 ACPL-214 30 20 10 0 -25 -5 15 35 55 Ambient Temperature, Ta( ºC) 75 95 140 120 80 60 40 20 0 -25 115 Figure 3. Forward Current vs. Ambient Temperature ACPL-214 100 0 25 50 75 Ambient Temperature, Ta(ºC) 100 Forward Current, I F (mA) Peak Forward Current, I FP (mA) Pulse width ≤100 µs Ta = 25 º C 1000 100 10 0.0001 0.0010 0.0100 0.1000 50 º C 10 1 0.4 1.0000 Figure 5. Pulse Forward Current vs.
PAGE 6
50 50 T a = 25ºC Collector Currrent, Ic( mA) Collector Current, Ic(mA) 20mA P C (max)=150mW 20 10mA 10 I F =5mA 35 5 Collector-Emitter Voltage, Vce(V) 30mA 30 25 20mA 20 15 10mA 10 5mA 5 0 0 50mA 40 30mA 30 0 45 50mA 40 10 Figure 9. Collector Current vs. Collector-Emitter Voltage I F = 2mA 0 0.5 Collector-Emitter Voltage, V CE(V) 1 Figure 10. Collector Current vs. Small Collector¬-Emitter Voltage 0.1 10V 1.
PAGE 7
1000 100 100 10mA 5mA 1mA I F = 0.5mA 75 Figure 15. Collector Current vs. Ambient Temperature Collector-Emitter Saturation Voltage, VCE(sat) (V) Switching time, t (µs) 10 t ON I F = 16mA VCC = 5V R L = 1.9kΩ 0 20 40 60 Ambient Temperature, Ta ( ºC) 100 5 tS 0.1 -20 10 Load Resistance, R L (kΩ) Figure 16. Switching Time vs. Load Resistance t OFF 1 1 80 100 Figure 17. Switching Time vs. Ambient Temperature Ta = 25 ºC 4 3 2 7mA 100 0.1 100 Ta = 25 ºC V CC = 5V R L = 1.