HP EliteBook 2740p User Guide Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
© Copyright 2010 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel is a trademark of Intel Corporation in the U.S. and other countries or regions. Java is a U.S. trademark of Sun Microsystems, Inc. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Table of contents 1 Features Identifying hardware ............................................................................................................................. 1 Top components .................................................................................................................. 1 Pointing devices .................................................................................................. 1 Lights ............................................................................
Connecting to a WLAN ...................................................................................................... 25 Roaming to another network .............................................................................................. 26 Using HP Mobile Broadband (select models only) ............................................................................. 27 Inserting a SIM ...................................................................................................................
Opening the Quick Launch Buttons control panel .............................................................................. 47 Using HP QuickLook 3 ....................................................................................................................... 48 Using the pen ..................................................................................................................................... 48 Identifying the pen components .........................................................
Viewing the current power plan ......................................................................... 64 Selecting a different power plan ........................................................................ 64 Customizing power plans .................................................................................. 64 Setting password protection on wakeup ............................................................................ 64 Using external AC power ...........................................
Using HP 3D DriveGuard software .................................................................................... 81 Replacing the hard drive in the hard drive bay ................................................................................... 82 8 External devices Using a USB device ........................................................................................................................... 86 Connecting a USB device .....................................................................
Using Computer Setup Auto DriveLock ........................................................................... 107 Entering an Automatic DriveLock password ................................................... 108 Removing Automatic DriveLock protection ..................................................... 108 Using Computer Setup security features .......................................................................................... 109 Securing system devices ...........................................
Choosing MultiBoot preferences ...................................................................................................... 140 Setting a new boot order in Computer Setup ................................................................... 140 Dynamically choosing a boot device using the F9 prompt ............................................... 140 Setting a MultiBoot Express prompt ................................................................................
xii Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
1 Features Identifying hardware To see a list of hardware installed in the computer, follow these steps: 1. Select Start > Computer > System properties. 2. In the left pane, click Device Manager. You can also add hardware or modify device configurations using Device Manager. NOTE: Windows® includes the User Account Control feature to improve the security of your computer.
Component Description (3) Pointing stick* Moves the pointer and selects or activates items on the screen. (4) fn key Enables/disables the TouchPad when pressed in combination with the f5 key. (5) Left pointing stick button* Functions like the left button on an external mouse. (6) TouchPad* Moves the pointer and selects or activates items on the screen. (7) Left TouchPad button* Functions like the left button on an external mouse.
Lights Component Description (1) ł On: The computer is on. ł Blinking: The computer is in the Sleep state. ł Off: The computer is off or in Hibernation. ł Amber: A battery is charging. ł Turquoise: A battery is close to full charge capacity. ł Blinking amber: A battery that is the only available power source has reached a low battery level. When the battery reaches a critical battery level, the battery light begins blinking rapidly.
Component Description (8) Volume up light Blinking: The volume scroll zone is being used to increase speaker volume. (9) Num lock light On: Num lock is on or the embedded numeric keypad is enabled. Buttons and switches 4 Component Description (1) Internal display switch Turns off the display if the display is closed while the power is on. (2) Volume mute button Mutes and restores speaker sound. (3) Volume down button Decreases computer volume.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortcut menu for items beneath the pointer. (5) Embedded numeric keypad keys Can be used like the keys on an external numeric keypad.
Front components Component Description (1) Webcam light On: The webcam is in use. (2) External WWAN antenna button Opens the external WWAN antenna. (3) External WWAN antenna Sends and receives wireless signals to communicate with WWANs. (4) Power switch ł When the computer is off, slide the switch to the right to turn on the computer. ł When the computer is on, slide the switch to the right to shut down the computer.
Right-side components Component Description (1) HP Fingerprint Sensor (fingerprint reader) Allows a fingerprint logon to Windows instead of a password logon. (2) QuickWeb button ł When the computer is off, press the button to open HP QuickWeb. ł When the computer is on, press the button to open the default Web browser. ł When the computer is off, press the button to open HP QuickLook. ł When the computer is on, press the button to open Software Setup.
Left-side components Component Description (1) Supports the following optional digital card formats: Media Card Reader ł Memory Stick ł Memory Stick Duo (adapter required) ł Memory Stick Pro (adapter required) ł Secure Digital (SD) Memory Card ł MultiMediaCard (MMC) ł xD-Picture Card ł xD-Picture Card Type H ł xD-Picture Card Type M (2) Pen holder Stores the pen. (3) Vent Enables airflow to cool internal components.
Rear components Component Description (1) In tablet mode, functions like the enter key and the up and down arrows on a standard keyboard. Jog dial ł Press inward to enter a command. ł Rotate up to scroll up. ł Rotate down to scroll down. (2) Esc button In tablet mode, allows you to exit or escape out of an application. (3) Rotate button In tablet mode, switches the image between landscape and portrait orientation.
Bottom components Component Description (1) Battery bay Holds the battery and subscriber identity module (SIM). (2) SIM slot Contains a wireless subscriber identity module (SIM) (select models only). The SIM slot is located inside the battery bay. (3) Vents (5) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Display Component Description (1) Webcam light (select models only) On: The webcam is in use. (2) Webcam (select models only) Records audio and video and captures still photographs. (3) Keyboard light button Opens and turns on the keyboard light. (4) HP Fingerprint Sensor (fingerprint reader) Allows a fingerprint logon to Windows instead of a password logon. (5) Internal microphones (2) Record sound and transmit sound for video conferencing and Voice Over IP (VoIP).
Wireless antennas (select models only) The antennas send and receive signals from one or more wireless devices. These antennas are not visible from the outside of the computer. Component Description (1) WWAN antenna (1)* Sends and receives wireless signals to communicate with wireless wide area networks (WWANs). (2) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLANs).
Additional hardware components Component Description (1) Power cord* Connects an AC adapter to an AC outlet. (2) AC adapter Converts AC power to DC power. (3) Battery* Powers the computer when the computer is not plugged into an external power source. (4) Modem cable (select models only)* Connects the internal modem to an RJ-11 telephone jack or to a country- or region-specific modem cable adapter.
Identifying the labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ł Service tag—Provides important information, including the following: Ń Product Name (1). This is the product name affixed to the front of your computer. Ń Serial Number (s/n) (2). This is an alphanumeric identifier that is unique to each product. Ń Part number/Product number (p/n) (3).
2 Using the tablet Tablet display components Component Description (1) ł While Windows is running, press the button with the pen to enter the ctrl+alt+delete command.† ł While the Computer Setup utility is running, press the button with the pen to enter the reset command. The computer resets and all unsaved information is lost. The reset function can be used to restore functionality when the system has become unresponsive.
(6) Pen holder Stores the pen. *This table describes default settings. For information about changing the functions of the Ctrl+alt+del button and jog dial, select Start > Control Panel > Hardware and Sound > Tablet PC Settings. † To protect your work and the system, the ctrl+alt+delete command cannot be entered using the ctrl, alt, and del keys on the on-screen keyboard. Rotating the display The computer display can rotate from traditional notebook mode to tablet mode.
2. Rotate the computer display clockwise until it snaps into place facing away from the keyboard. 3. Tilt the computer display downward onto the keyboard until it snaps into place. In tablet mode, the screen display automatically rotates from portrait to landscape as it is being turned. NOTE: If antennae on the computer are held in close proximity to the body, the antennae may disable automatic rotation of the screen display. Rotating the display Antenna House XSL Formatter (Evaluation) http://www.
Notebook mode To change the computer from tablet mode to notebook mode: 18 1. Slide the display release latch (1). 2. Open the computer display (2). Chapter 2 Using the tablet Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
3. Rotate the computer display counterclockwise until it snaps into place facing the keyboard. NOTE: To prevent a lack of response when you turn on the computer, be sure that the battery is firmly seated. Rotating the display Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
3 Wireless, modem, and local area network Using wireless devices (select models only) Wireless technology transfers data across radio waves instead of wires.
For more information on wireless technology, refer to the information and Web site links provided in Help and Support. Identifying wireless and network icons Icon Name Description Wireless (connected) Identifies the location of the wireless lights and the wireless buttons on the computer. Also identifies the Wireless Assistant software on the computer and indicates that one or more of the wireless devices are on.
The wireless light indicates the overall power state of your wireless devices, not the status of individual devices. If the wireless light is blue, at least one wireless device is on. If the wireless light is off, all wireless devices are off. NOTE: On some models, the wireless light is amber when all wireless devices are off. Because the wireless devices are enabled at the factory, you can use the wireless button to turn on or turn off the wireless devices simultaneously.
For more details about using Connection Manager, refer to the Connection Manager software Help. Using operating system controls Some operating systems also offer a way to manage integrated wireless devices and the wireless connection. For example, Windows provides the Network and Sharing Center that allows you to set up a connection or network, connect to a network, manage wireless networks, and diagnose and repair network problems.
Using a WLAN With a WLAN device, you can access a wireless local area network (WLAN), which is composed of other computers and accessories that are linked by a wireless router or a wireless access point. NOTE: The terms wireless router and wireless access point are often used interchangeably. ł A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points that can accommodate a large number of computers and accessories and can separate critical network functions.
When you set up a WLAN or access an existing WLAN, always enable security features to protect your network from unauthorized access. The common security levels are Wi-Fi Protected Access (WPA) and Wired Equivalent Privacy (WEP). Because wireless radio signals travel outside the network, other WLAN devices can pick up unprotected signals and either connect to your network (uninvited) or capture information being sent across it.
After the connection is made, place the mouse pointer over the network icon in the notification area, at the far right of the taskbar, to verify the name and status of the connection. NOTE: The functional range (how far your wireless signals travel) depends on WLAN implementation, router manufacturer, and interference from other electronic devices or structural barriers such as walls and floors.
Using HP Mobile Broadband (select models only) HP Mobile Broadband enables your computer to use wireless wide area networks (WWANs) to access the Internet from more places and over larger areas than it can by using WLANs. Using HP Mobile Broadband requires a network service provider (called a mobile network operator), which in most cases is a mobile phone network operator. Coverage for HP Mobile Broadband is similar to mobile phone voice coverage.
7. Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated. 8. Replace the battery. NOTE: HP Mobile Broadband will be disabled if the battery is not replaced. 9. Turn the computer right-side up, and then reconnect external power and external devices. 10. Turn on the computer. Removing a SIM To remove a SIM: 28 1. Shut down the computer.
7. Press in on the SIM (1), and then remove it from the slot (2). 8. Replace the battery. 9. Turn the computer right-side up, and then reconnect external power and external devices. 10. Turn on the computer. Using HP Mobile Broadband (select models only) Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Using Bluetooth wireless devices (select models only) A Bluetooth device provides short-range wireless communications that replace the physical cable connections that traditionally link electronic devices, such as the following: ł Computers (desktop, notebook, PDA) ł Phones (cellular, cordless, smart phone) ł Imaging devices (printer, camera) ł Audio devices (headset, speakers) Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network (PAN) of Bluetooth devi
Troubleshooting wireless connection problems Some possible causes for wireless connection problems include the following: ł Wireless device is not installed correctly or has been disabled. ł Wireless device or router hardware has failed. ł Network configuration (SSID or security) has been changed. ł Wireless device encountered interference from other devices. NOTE: Wireless networking devices are included with select computer models only.
Cannot connect to a preferred network Windows can automatically repair a corrupted WLAN connection: ł If there is a network icon in the notification area, at the far right of the taskbar, right-click the icon, and then click Troubleshoot problems. Windows resets your network device and attempts to reconnect to one of the preferred networks. ł If there is no network icon in the notification area, follow these steps: 1. Select Start > Control Panel > Network and Internet > Network and Sharing Center. 2.
If you are provided with new wireless network keys and SSID for a network, and if you have previously connected to that network, follow the steps below to connect to the network: 1. Select Start > Control Panel > Network and Internet > Network and Sharing Center. 2. Click Manage wireless networks in the left panel. A list showing the available WLANs is displayed. If you are in a hotspot where several WLANs are active, several will be displayed. 3.
Using the modem (select models only) The modem must be connected to an analog telephone line using a 6-pin, RJ-11 modem cable (included with select models only). In some countries, a country-specific modem cable adapter (included with select models only) is also required. Jacks for digital PBX systems may resemble analog telephone jacks, but they are not compatible with the modem. WARNING! Connecting the internal analog modem to a digital line can permanently damage the modem.
To connect the modem to an analog telephone line that does not have an RJ-11 telephone jack, follow these steps: 1. Plug the modem cable into the modem jack (1) on the computer. 2. Plug the modem cable into the country-specific modem cable adapter (2). 3. Plug the country-specific modem cable adapter (3) into the telephone wall jack. Selecting a location setting Viewing the current location selection To view the current location setting for the modem, follow these steps: 1.
Adding new locations when traveling By default, the only location setting available to the modem is a location setting for the country in which you purchased the computer. As you travel to different countries, set the internal modem to a location setting that meets the operating standards of the country in which you are using the modem. As you add new location settings, they are saved by the computer so that you can switch among settings at any time. You can add multiple location settings for any country.
Solving travel connection problems If you experience modem connection problems when using the computer outside of the country in which you purchased it, try the following suggestions: ł Check the telephone line type. The modem requires an analog, not a digital, telephone line. A line described as a PBX line is usually a digital line. A telephone line described as a data line, fax machine line, modem line, or standard telephone line is usually an analog line. ł Check for pulse or tone dialing.
38 7. Clear the check box for Wait for dial tone before dialing. 8. Click OK twice. Chapter 3 Wireless, modem, and local area network Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Connecting to a local area network (LAN) Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased separately). If the network cable contains noise suppression circuitry (1), which prevents interference from TV and radio reception, orient the circuitry end of the cable (2) toward the computer. To connect the network cable: 1. Plug the network cable into the network jack (1) on the computer. 2. Plug the other end of the cable into a network wall jack (2).
4 Pointing devices and keyboard Using pointing devices Setting pointing device preferences Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options. To access Mouse Properties, select Start > Control Panel > Hardware and Sound > Mouse. Using the TouchPad To move the pointer, slide your finger across the TouchPad surface in the direction you want the pointer to go.
䦱 To open and turn on the keyboard light, press the keyboard light button. 䦱 To turn off and close the keyboard light, gently press the keyboard light button until it clicks into place. Using the keyboard Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Using hotkeys Hotkeys are combinations of the fn key (1) and either the esc key (2) or one of the function keys (3). The icons on the f3 through f5, and f8 through f11 keys represent the hotkey functions. Hotkey functions and procedures are discussed in the following sections. Function Hotkey Display system information. fn+esc Initiate Sleep. fn+f3 Switch the screen image. fn+f4 Enable/disable the TouchPad Fn+f5 Display battery information. fn+f8 Decrease screen brightness.
In the Windows fn+esc display, the version of the system BIOS (basic input-output system) is displayed as the BIOS date. On some computer models, the BIOS date is displayed in decimal format. The BIOS date is sometimes called the system ROM version number. Initiating Sleep CAUTION: To reduce the risk of information loss, save your work before initiating Sleep. Press fn+f3 to initiate Sleep.
Viewing battery charge information Press fn+f8 to display charge information for all installed batteries. The display indicates which batteries are charging and reports the amount of charge remaining in each battery. Enabling/disabling the TouchPad (fn+f5) Press fn+f5 to enable or disable the TouchPad. Decreasing screen brightness Press fn+f9 to decrease screen brightness. Hold down the hotkey to decrease the brightness level incrementally.
Using QuickLook (select models only) NOTE: QuickLook must be installed before you can view the QuickLook information. QuickLook saves Inbox e-mails and calendar, contact, and task information from Microsoft® Outlook to your computer's hard drive. When the computer is off, in the Sleep state, or in Hibernation, you can quickly view this information by pressing the info button on the computer.
Using HP Quick Launch Buttons The HP Quick Launch Buttons enable you to quickly open programs, files, or Web sites you use frequently. You can use the factory settings, which are described in the following table. Or you can reprogram the buttons by opening the Q Menu in the Quick Launch Buttons control panel. The Quick Launch Buttons include the QuickWeb button (1), and the QuickLook button (2) . The following table describes the factory settings for the Quick Launch Buttons.
Opening the Quick Launch Buttons control panel You can open the HP Quick Launch Buttons control panel in any of the following ways: ł Select Start > Control Panel > Hardware and Sound > Quick Launch Buttons. ł Double-click the HP Quick Launch Buttons icon in the notification area, at the far right of the taskbar. ł Right-click the HP Quick Launch Buttons icon in the notification area, and click Adjust HP Quick Launch Buttons Properties. NOTE: On some models, an icon is displayed on the desktop.
Using HP QuickLook 3 QuickLook 3 allows you to save calendar, contact, inbox, and task information from Microsoft Outlook to the hard drive of your computer. Then, when the computer is off or in Hibernation, you can press the QuickLook button on the computer to view this information without waiting for the operating system to restart. Use QuickLook 3 to manage contact information, calendar events, e-mail information, and tasks without restarting your computer.
Performing mouse clicks with the pen 䦱 To select an item on the screen as you would with the left button of an external mouse, tap the item with the tip of the pen. 䦱 To double-click an item on the screen as you would with the left button of an external mouse, tap the item twice with the tip of the pen. 䦱 To select an item as you would with the right button of an external mouse, press and hold down the pen button, and then tap the item with the tip of the pen.
Calibrating the pen The pen can function at the default calibration or at a calibration set by another user. However, HP highly recommends that you use the pen only while it is calibrated to your personal handwriting and mouse action motions. Calibration optimizes pen performance for all users and particularly for left-handed users. To calibrate the pen: 1. Select Start > Control Panel > Hardware and Sound > Tablet PC Settings. 2. At the bottom of the General tab, tap the Calibrate button. 3.
Setting pen preferences Pen preferences are set in the Tablet PC Settings window of the operating system. The preferences include setting the location of on-screen menus for either right-handed or left-handed users, calibrating the screen for pen use, and optimizing handwriting recognition. To access pen preferences: 䦱 Select Start > Control Panel > Hardware and Sound > Tablet PC Settings. Pen options are set in the Pen and Input Devices window.
Cleaning the TouchPad and keyboard Dirt and grease on the TouchPad can cause the pointer to jump around on the screen. To avoid this, clean the TouchPad with a damp cloth, and wash your hands frequently when using the computer. WARNING! To reduce the risk of electric shock or damage to internal components, do not use a vacuum cleaner attachment to clean the keyboard. A vacuum cleaner can deposit household debris on the keyboard surface.
5 Multimedia Multimedia features Your computer includes multimedia features that allow you to listen to music, watch movies, and view pictures.
Ń ł To increase volume, press and hold the volume up button (3) until the desired volume level is reached. Windows volume control: a. Click the Speakers icon in the notification area, at the far right of the taskbar. b. Increase or decrease the volume by moving the slider up or down. Click the Mute Speakers icon to mute the volume. – or – a. Right-click the Speakers icon in the notification area, and then click Open Volume Mixer. b.
Depending on the hardware and software included with the computer, the following multimedia tasks may be supported: ł Playing digital media, including audio and video CDs, audio and video DVDs, and Internet radio ł Creating or copying data CDs ł Creating, editing, and burning audio CDs ł Creating, editing, and burning a video or movie to a DVD or video CD CAUTION: To prevent loss of information or damage to a disc, observe the following guidelines: Before writing to a disc, connect the computer to
Audio Your computer enables you to use a variety of audio features: ł Play music using your computer speakers and/or connected external speakers ł Record sound using the internal microphone or connect an external microphone ł Download music from the Internet ł Create multimedia presentations using audio and images ł Transmit sound and images with instant messaging programs ł Stream radio programs (select models only) or receive FM radio signals ł Create or “burn” audio CDs (select models only)
NOTE: For best results when recording, speak directly into the microphone and record sound in a setting free of background noise. To confirm or change the audio settings on your computer, select Start > Control Panel > Hardware and Sound > Sound. Audio Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Video Your computer enables you to use a variety of video features: ł Watch movies ł Play games over the Internet ł Edit pictures and video to create presentations ł Connect external video devices Connecting an external monitor or projector Your computer has an external monitor port that allows you to connect external monitors and projectors. Using the external monitor port The external monitor port connects an external display device, such as an external monitor or a projector, to the computer.
Webcam NOTE: This section describes features that are common to most models. Some features may not be available on your computer. Your computer includes an integrated webcam, located at the top of the display. With the preinstalled software, you can use the webcam to take a photo, record a video, or make an audio recording. You can preview the photo, video recording, or audio recording, and save it on your computer hard drive.
ł Hue—Controls the aspect of color that distinguishes it from another color (what makes a color red, green, or blue). Hue is distinct from saturation, which measures the intensity of the hue. ł Saturation—Controls the strength of color in the final image. A higher saturation setting creates a bolder image; a lower saturation setting creates a more subtle image. ł Sharpness—Controls the definition of edges in an image.
4. Insert a business card into the business card slot on the front of the computer (1) and slide the card to the right (2) to align it with the webcam. NOTE: Be sure that text on the bottom of the card is not obscured by the slot. If any text is obscured by the slot, rotate the card 180 degrees. The webcam captures the business card image and the webcam light turns off. 5. If you are capturing multiple business card images, remove the business card and insert another one.
6 Power management Setting power options Using power-saving states The computer has two power-saving states enabled at the factory: Sleep and Hibernation. When Sleep is initiated, the power lights blink and the screen clears. Your work is saved to memory. Exiting Sleep is faster than exiting Hibernation. If the computer is in the Sleep state for an extended period or if the battery reaches a critical battery level while in the Sleep state, the computer initiates Hibernation.
NOTE: If you have set a password to be required when the computer exits Sleep, you must enter your Windows password before your work will return to the screen. Initiating and exiting Hibernation The system is set at the factory to initiate Hibernation after 1080 minutes (18 hours) of inactivity when running on battery power, 1080 minutes (18 hours) of inactivity when running on external power, or when the battery reaches a critical battery level.
Viewing the current power plan 䦱 Move the pointer over the battery meter icon in the notification area, at the far right of the taskbar. – or – Select Start > Control Panel > System and Maintenance > Power Options. Selecting a different power plan 䦱 Click the battery meter icon in the notification area, and then select a power plan from the list. – or – Select Start > Control Panel > System and Maintenance > Power Options, and then select a power plan from the list. Customizing power plans 1.
Using external AC power External AC power is supplied through one of the following devices: WARNING! To reduce potential safety issues, use only the AC adapter provided with the computer, a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP. ł Approved AC adapter ł Optional docking device Connect the computer to external AC power under any of the following conditions: WARNING! Do not charge the computer battery while you are onboard aircraft.
3. Plug the other end of the power cord into an AC outlet (3). Using battery power When a charged battery is in the computer and the computer is not plugged into external power, the computer runs on battery power. When the computer is plugged into external AC power, the computer runs on AC power. If the computer contains a charged battery and is running on external AC power supplied through the AC adapter, the computer switches to battery power if the AC adapter is disconnected from the computer.
Using Battery Check Battery Check provides information on the status of the battery installed in the computer. To run Battery Check: 1. Connect the AC adapter to the computer. NOTE: 2. The computer must be connected to external power for Battery Check to function properly. Select Start > Help and Support > Troubleshoot > Power, Thermal and Mechanical, and then click the Power tab.
3. Press the battery (2) into the battery bay until the battery clicks into place. To remove the battery: 1. Turn the computer upside down on a flat surface, with the battery bay toward you. 2. Slide the battery release latch (1) to release the battery. 3. Pivot the battery upward (2), and remove the battery from the computer (3). Charging a battery WARNING! Do not charge the computer battery while you are onboard aircraft.
To prolong battery life and optimize the accuracy of battery charge displays, follow these recommendations: ł If you are charging a new battery, charge it fully before turning on the computer. ł Charge the battery until the battery light turns off. NOTE: If the computer is on while the battery is charging, the battery meter in the notification area may show 100 percent charge before the battery is fully charged.
The computer takes the following actions for a critical battery level: 70 ł If Hibernation is enabled and the computer is on or in the Sleep state, the computer initiates Hibernation. ł If Hibernation is disabled and the computer is on or in the Sleep state, the computer remains briefly in the Sleep state, and then shuts down and loses any unsaved information. Chapter 6 Power management Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Resolving a low battery level CAUTION: To reduce the risk of losing information when the computer reaches a critical battery level and has initiated Hibernation, do not restore power until the power lights turn off. Resolving a low battery level when external power is available 䦱 Connect one of the following devices: ł AC adapter ł Optional expansion product or docking device ł Optional power adapter Resolving a low battery level when a charged battery is available 1.
To fully charge the battery: 1. Insert the battery into the computer. 2. Connect the computer to an AC adapter, optional power adapter, optional expansion product, or optional docking device, and then plug the adapter or device into external power. The battery light on the computer turns on. 3. Leave the computer plugged into external power until the battery is fully charged. The battery light on the computer turns off. Step 2: Disable Hibernation and Sleep 1.
To discharge a battery: 1. Unplug the computer from its external power source, but do not turn off the computer. 2. Run the computer on battery power until the battery is discharged. The battery light begins to blink when the battery has discharged to a low battery level. When the battery is discharged, the battery light turns off and the computer shuts down. Step 4: Fully recharge the battery To recharge the battery: 1.
ł Disconnect external devices that are not plugged into an external power source, when you are not using them. ł Stop, disable, or remove any external media cards that you are not using. ł Use the fn+f9 and fn+f10 hotkeys to adjust screen brightness as needed. ł If you leave your work, initiate Sleep or Hibernation, or shut down the computer. Storing a battery CAUTION: To prevent damage to a battery, do not expose it to high temperatures for extended periods of time.
Testing an AC adapter Test the AC adapter if the computer exhibits any of the following symptoms: ł The computer will not turn on when connected to the AC adapter. ł The display does not turn on when the computer is connected to the AC adapter and external power. ł The power light is off when the computer is connected to the AC adapter. To test the AC adapter: 1. Remove the battery from the computer. 2. Connect the AC adapter to the computer and to an AC outlet. 3. Turn on the computer.
If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the following emergency procedures in the sequence provided: 76 ł Slide the power switch to the right and hold it for at least 5 seconds. ł Disconnect the computer from external power and remove the battery. Chapter 6 Power management Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
7 Drives Identifying installed drives Your computer includes a hard drive (with a rotating disc) or a solid-state drive (SSD) with solid-state memory. Because it has no moving parts, an SSD does not generate as much heat as a hard drive. To view the drives installed on the computer, select Start > Computer. NOTE: Windows includes the User Account Control feature to improve the security of your computer.
Handling drives Drives are fragile computer components that must be handled with care. Refer to the following cautions before handling drives. Additional cautions are included with the procedures to which they apply. CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information, observe these precautions: Before you move a computer or external hard drive from one location, initiate Sleep, and allow the screen to clear.
Improving hard drive performance Using Disk Defragmenter As you use the computer, files on the hard drive become fragmented. Disk Defragmenter consolidates the fragmented files and folders on the hard drive so that the system can run more efficiently. After you start Disk Defragmenter, it works without supervision. Depending on the size of your hard drive and the number of fragmented files, Disk Defragmenter may take more than an hour to complete.
Using HP 3D DriveGuard HP 3D DriveGuard protects the hard drive by parking the drive and halting I/O requests under either of the following conditions: ł You drop the computer. ł You move the computer with the display closed while the computer is running on battery power. A short time after the end of one of these events, HP 3D DriveGuard returns the hard drive to normal operation. NOTE: If the upgrade bay contains a hard drive, the hard drive is protected by HP 3D DriveGuard.
Using HP 3D DriveGuard software The HP 3D DriveGuard software enables you to perform the following tasks: ł Enable and disable HP 3D DriveGuard. NOTE: Permission to enable or disable HP 3D DriveGuard is dependent on certain user privileges. Members of an Administrator group can change privileges for non-Administrator users. ł Determine whether a drive in the system is supported. To open the software and change settings, follow these steps: 1.
Replacing the hard drive in the hard drive bay CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by sliding the power switch to the right. Then shut down the computer through the operating system. To remove a hard drive: 82 1.
10. Remove the hard drive bracket (2). 11. Grasp the mylar tab on the hard drive and pull upward (1) until the hard drive is at a 45-degree angle. 12. With the hard drive at a 45-degree angle, pull it forward (2) until the rear of the hard drive is clear of the computer back edge. 13. Lift the hard drive (3) out of the hard drive bay. To install a hard drive: 1. Insert the rear of the hard drive at a 45-degree angle into the back of the hard drive bay (1).
84 2. Lower the front of the hard drive down onto the system board connector (2), and then press down (3) to connect the hard drive. 3. Replace the hard drive bracket (1). 4. Replace the 2 hard drive bracket screws (2). 5. Align the tabs (1) on the hard drive cover with the notches on the computer. 6. Close the cover (2). Chapter 7 Drives Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
7. Tighten the 3 hard drive cover screws (3). 8. Replace the battery. 9. Turn the computer right-side up, and then reconnect external power and external devices. 10. Turn on the computer. Replacing the hard drive in the hard drive bay Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
8 External devices Using a USB device Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Some USB devices may require additional support software, which is usually included with the device. For more information about device-specific software, refer to the manufacturer's instructions. Your computer model has 3 USB ports, which support USB 1.0, USB 1.1, and USB 2.0 devices.
CAUTION: To prevent damage to a USB connector, do not pull on the cable to remove the USB device. To stop and remove a USB device: 1. Double-click the Safely Remove Hardware icon in the notification area, at the far right of the taskbar. NOTE: To display the Safely Remove Hardware icon, click the Show Hidden Icons icon (< or <<) in the notification area. 2. Click the name of the device in the list. NOTE: If the USB device is not listed, you do not have to stop the device before you remove it. 3.
Using a 1394 device IEEE 1394 is a hardware interface that connects a high-speed multimedia or data storage device to the computer. Scanners, digital cameras, and digital camcorders often require a 1394 connection. Some 1394 devices may require additional support software, which is usually included with the device. For more information about device-specific software, refer to the manufacturer's instructions. The 1394 port also supports IEEE 1394a devices.
Using external drives Removable external drives expand your options for storing and accessing information. A USB drive can be added by connecting the drive to a USB port on the computer. USB drives include the following types: ł 1.
Using the docking connector The docking connector connects the computer to an optional docking device. An optional docking device provides additional ports and connectors that can be used with the computer. 90 Chapter 8 External devices Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
9 External media cards Using Media Card Reader cards Optional digital cards provide secure data storage and convenient data sharing. These cards are often used with digital media–equipped cameras and PDAs as well as with other computers.
2. Insert the card into the Media Card Reader, and then push in on the card until it is firmly seated. You will hear a sound when the device has been detected, and a menu of available options may be displayed. Stopping and removing a digital card CAUTION: To prevent loss of data or an unresponsive system, stop a digital card before removing it. 1. Save your information and close all programs associated with the digital card.
Using ExpressCards (select models only) An ExpressCard is a high-performance PC Card that is inserted into the ExpressCard slot. Like standard PC Cards, ExpressCards are designed to conform to the standard specifications of the Personal Computer Memory Card International Association (PCMCIA). Configuring an ExpressCard Install only the software required for your device.
2. Insert the card into the ExpressCard slot, and then push in on the card until it is firmly seated. You will hear a sound when the device has been detected, and a menu of options may be displayed. NOTE: The first time you insert an ExpressCard, a message is displayed in the notification area to let you know the device is recognized by the computer. NOTE: An inserted ExpressCard uses power even when idle. To conserve power, stop or remove an ExpressCard when it is not in use.
Using ExpressCards (select models only) Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Using Smart Cards (select models only) NOTE: The term smart card is used throughout this chapter to refer to both smart cards and Java™ Cards. A smart card is a credit card–sized accessory that carries a microchip containing memory and a microprocessor. Like personal computers, smart cards have an operating system to manage input and output, and they include security features to protect against tampering. Industry-standard smart cards are used with the smart card reader (select models only).
10 Memory modules The computer has one memory module compartment located on the bottom of the computer. The memory capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the memory module slot. WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module.
Adding or replacing a memory module To add or replace a memory module in the memory module slot, follow these steps: 1. Save your work. 2. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the computer on by sliding the power switch to the right. Then shut down the computer through the operating system. 3. Disconnect all external devices connected to the computer. 4. Unplug the power cord from the AC outlet. 5.
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory module slot. To protect a memory module after removal, place it in an electrostatic-safe container. 10. Insert a memory module: NOTE: If you are inserting a memory module and both memory module slots are vacant, be sure that you insert the memory module into the primary memory module slot. a. Align the notched edge (1) of the memory module with the tab in the memory module slot.
12. Close the cover (2). 13. Tighten the 3 hard drive compartment cover screws (3). 14. Replace the batteries. 15. Turn the computer right-side up, and then reconnect external power and external devices. 16. Turn on the computer. 100 Chapter 10 Memory modules Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
11 Security Protecting the computer NOTE: Security solutions are designed to act as deterrents. These deterrents may not prevent a product from being mishandled or stolen. NOTE: Your computer supports CompuTrace, which is an online security-based tracking and recovery service available in select regions. If the computer is stolen, CompuTrace can track the computer if the unauthorized user accesses the Internet. You must purchase the software and subscribe to the service in order to use CompuTrace.
Using passwords Most security features use passwords. Whenever you set a password, write down the password and store it in a secure location away from the computer. Note the following password considerations: ł Setup and DriveLock passwords are set in Computer Setup and are managed by the system BIOS.
BIOS administrator passwords Function DriveLock user password Protects access to the internal hard drive that is protected by DriveLock, and is set under DriveLock Passwords during the enable process. TPM embedded security password When enabled as a BIOS administrator password, protects access to the computer contents when the computer turns on, restarts, or exits Hibernation. This password requires the optional embedded security chip to support this security feature.
Managing a BIOS administrator password A BIOS administrator password is set, changed, and deleted in Computer Setup. To set or change this password in Computer Setup, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3. Use a pointing device or the arrow keys to select Security > Change Password, and then press enter. 4.
Entering a BIOS administrator password At the BIOS administrator password prompt, type your password (using the same kind of keys you used to set the password), and then press enter. After three unsuccessful attempts to enter the BIOS administrator password, you must restart the computer and try again.
Setting a DriveLock password To set a DriveLock password in Computer Setup, follow these steps: 1. Turn on the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3. Use a pointing device or the arrow keys to select Security > DriveLock passwords, and then press enter. 4. Use a pointing device to click the hard drive you want to protect.
3. Use a pointing device or the arrow keys to select Security > DriveLock passwords, and then press enter. 4. Use a pointing device to select an internal hard drive. – or – Use the arrow keys to select an internal hard drive, and then press enter. 5. Use a pointing device or the arrow keys to select the password you want to change. 6. Type your current password in the Old password field, type a new password in the New password and Verify new password fields, and then press enter. 7.
Entering an Automatic DriveLock password To enable an Automatic DriveLock password in Computer Setup, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3. Use a pointing device or the arrow keys to select Security > Automatic DriveLock, and then press enter. 4.
Using Computer Setup security features Securing system devices You can disable or enable system devices from the following menus in Computer Setup: ł Boot Options ł Device Configurations ł Built-In Device Options ł Port Options To disable or reenable system devices in Computer Setup, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3.
To view this general system information in Computer Setup, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3. Use a pointing device or the arrow keys to select File > System Information, and then press enter. NOTE: To prevent unauthorized access to this information, you must create a BIOS administrator password in Computer Setup.
Using antivirus software When you use the computer to access e-mail, a network, or the Internet, you expose the computer to computer viruses. Computer viruses can disable the operating system, programs, or utilities, or cause them to function abnormally. Antivirus software can detect most viruses, destroy them, and in most cases, repair any damage they have caused. To provide ongoing protection against newly discovered viruses, antivirus software must be kept up to date.
Using firewall software When you use the computer to access e-mail, a network, or the Internet, unauthorized persons may be able to gain access to the computer, your personal files, and information about you. Use the firewall software preinstalled on the computer to protect your privacy. McAfee Total Protection antivirus software is preinstalled on the computer. To access your software, select Start > All Programs > McAfee > Managing Services > Total Protection.
Installing critical updates CAUTION: Microsoft sends alerts regarding critical updates. To protect the computer from security breaches and computer viruses, install all critical updates from Microsoft as soon as you receive an alert. Updates to the operating system and other software may have become available after the computer was shipped.
Using HP ProtectTools Security Manager (select models only) HP ProtectTools Security Manager software is preinstalled on select computer models. This software can be accessed through Windows Control Panel. It provides security features that help protect against unauthorized access to the computer, networks, and critical data. For more information, refer to the HP ProtectTools online Help. 114 Chapter 11 Security Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Installing a security cable NOTE: A security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. 1. Loop the security cable around a secured object. 2. Insert the key (1) into the cable lock (2). 3. Insert the cable lock into the security cable slot on the computer (3), and then lock the cable lock with the key. NOTE: The location of the security cable slot varies by computer model.
12 Software updates Updating software Updated versions of the software provided with your computer are available either through the HP Assistant utility or on the HP Web site. HP Assistant automatically checks for updates from HP. The utility runs at a specified interval and provides a list of support alerts, such as security enhancements, and optional software and driver updates.
To update the software using the HP Web site, follow these steps: 1. Identify your computer model, product category, and series or family. Prepare for a system BIOS update by identifying the BIOS version currently installed on the computer. For details, refer to the "Determining the BIOS version" section. If your computer is connected to a network, consult the network administrator before installing any software updates, especially system BIOS updates.
Updating the BIOS To update the BIOS, first determine what BIOS version you currently have, and then download and install the new BIOS. Determining the BIOS version BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing fn+esc (if you are already in Windows) or by using Computer Setup. To use Computer Setup for displaying BIOS information, follow these steps: 1.
Downloading a BIOS update CAUTION: To prevent damage to the computer or an unsuccessful installation, download and install a BIOS update only when the computer is connected to reliable external power using the AC adapter. Do not download or install a BIOS update while the computer is running on battery power, docked in an optional docking device, or connected to an optional power source.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information. 5. Complete the installation by following the on-screen instructions. NOTE: After a message on the screen reports a successful installation, you may delete the downloaded file from your hard drive.
Updating programs and drivers 1. Open your Internet browser, go to http://www.hp.com/support, and then select your country or region. 2. Click the option for software and driver downloads, type your computer model number in the product box, and then press enter. – or – If you want a specific SoftPaq, type the SoftPaq number in the Search box, at the top-right corner of the screen. Then press enter, and follow the instructions provided. Proceed to step 6. 3.
Using SoftPaq Download Manager HP SoftPaq Download Manager (SDM) is a tool that provides quick access to SoftPaq information for HP business computers without requiring the SoftPaq number. Using this tool, you can easily search for SoftPaqs and then download and unpack them. SoftPaq Download Manager works by reading and downloading, from the HP FTP site, a published database file containing computer model and SoftPaq information.
13 Backup and recovery To protect your information, use Windows Backup and Restore to back up individual files and folders, back up your entire hard drive (select models only), create system repair discs (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
Backing up your information Recovery after a system failure is as complete as your most current backup. You should create system repair discs (select models only) and your initial backup immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information. Backing up your information 125 Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Performing a recovery In case of system failure or instability, the computer provides the following tools to recover your files: ł Windows recovery tools: You can use Windows Backup and Restore to recover information you have previously backed up. You can also use Windows Startup Repair to fix problems that might prevent Windows from starting correctly. ł f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image.
NOTE: For additional information on recovering information using the Windows tools, perform a search for these topics in Help and Support. Using f11 CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed. The f11 recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled.
6. Select Repair your computer. 7. Follow the on-screen instructions. 128 Chapter 13 Backup and recovery Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
14 Computer Setup Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer. NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy support is enabled. To start Computer Setup, follow these steps: 1.
To exit Computer Setup menus, choose one of the following methods: ł To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the tab key and the arrow keys to select File > Ignore changes and exit, and then press enter. – or – ł To save your changes and exit Computer Setup menus, click the Save icon in the lower-left corner of the screen, and then follow the on-screen instructions.
File menu Select To do this System Information ł View identification information for the computer and the batteries in the system. ł View specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version. Set System Date and Time Set or change the date and time on the computer. Restore defaults Replace the configuration settings in Computer Setup with the original factory settings.
Select To do this TPM Embedded Security Enable/disable support for Trusted Platform Module (TPM) Embedded Security, which protects the computer from unauthorized access to owner functions available in Embedded Security for ProtectTools. For more information, refer to the ProtectTools software Help. NOTE: You must have a setup password to change this setting. Automatic DriveLock Enable/disable Automatic DriveLock support.
System Configuration menu NOTE: Some of the listed System Configuration options may not be supported by your computer. Select To do this Language Change the Computer Setup language. Boot Options ł Set a Startup Menu delay (in seconds). ł Enable/disable Custom Logo (disabled by default). ł Enable/disable Display Diagnostic URL (enabled by default). ł Enable/disable CD-ROM boot (enabled by default). ł Enable/disable SD Card boot (enabled by default).
Select To do this NOTE: Availability of the options above varies by computer model. Built-In Device Options 134 Chapter 14 Computer Setup Antenna House XSL Formatter (Evaluation) http://www.antennahouse.com/ ł Enable/disable secondary battery fast charge (enabled by default). ł Enable/disable HP QuickLook 2 (enabled by default). ł Enable/disable Virtualization Technology (select models only; disabled by default).
Select To do this Port Options NOTE: All port options are enabled by default. ł Enable/disable the Smart Card slot. ł Enable/disable the ExpressCard slot. ł Enable/disable the serial port. ł Enable/disable the parallel port. ł Enable/disable the flash media reader. ł Enable/disable the USB port. CAUTION: Disabling the USB port also disables MultiBay devices and ExpressCard devices on the advanced port replicator. ł AMT Options Enable/disable the 1394 port.
15 MultiBoot About the boot device order As the computer starts, the system attempts to boot from enabled boot devices. The MultiBoot utility, which is enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices contain bootable media or files that the computer needs to start and operate properly.
NOTE: An optical drive (such as a CD-ROM drive) can boot either as drive A or drive C, depending on the format of the boot CD. The following list describes the factory setting for boot order in which drive letters A and C are assigned when MultiBoot is disabled. (The actual order varies by configuration.) ł ł Boot order for drive A boot devices: 1. Optical drive in an optional docking device or in an optional external MultiBay that contains a disc formatted as drive A 2.
Enabling boot devices in Computer Setup The computer will boot to a USB device or a NIC device only if the device has first been enabled in Computer Setup. To start Computer Setup and enable a USB device or a NIC device as a boot device, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3.
Considering boot order changes Before changing the boot order, note the following considerations: ł When the computer restarts after the boot order has been changed, the computer attempts to start using the new boot order. ł If there is more than one type of boot device, the computer attempts to boot using the first of each type of boot device (except for optical devices).
Choosing MultiBoot preferences You can use MultiBoot in the following ways: ł To set a new boot order that the computer uses each time it is turned on, by changing the boot order in Computer Setup. ł To dynamically choose the boot device, by pressing esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot Device Options menu. ł To use MultiBoot Express to set variable boot orders.
Your changes go into effect immediately. Setting a MultiBoot Express prompt To start Computer Setup and set the computer to display the MultiBoot startup location menu each time the computer is started or restarted, follow these steps: 1. Turn on or restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 2. Press f10 to enter BIOS Setup. 3.
16 Management and printing Using Client Management Solutions Client Management Solutions software provides standards-based solutions for managing client (user) desktop, workstation, notebook, and tablet computers in a networked environment.
Managing and updating software HP provides several tools for managing and updating software on client computers: ł HP Client Manager for Altiris (select models only) NOTE: To download HP Client Manager for Altiris or to obtain more information about HP Client Manager for Altiris, see the HP Web site at http://www.hp.com.
ł ł Help desk and problem resolution Ń Management of help desk tickets Ń Remote troubleshooting Ń Remote problem resolution Ń Client disaster recovery Software and operations management Ń Ongoing client management Ń HP system software deployment Ń Application self-healing (the ability to identify and repair certain application problems) Altiris Solutions software provides easy-to-use software distribution capabilities.
Web site and on the Support Software CD. To download the SSM utility or to obtain more information on SSM, see the HP Web site at http://www.hp.com/go/ssm (English only). Using Client Management Solutions 145 Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
Using Intel Active Management Technology (select models only) Intel® Active Management Technology (iAMT) allows discovery, repair, and protection of networked computing assets. With iAMT, computers can be managed whether they are on or off. The iAMT solution is available on computers with Intel Centrino® with vPro mobile technology.
iAMT Configuration Select To do this Host Name Assign a host name to the computer. TCP/IP Disable/enable network interface or DHCP (assigns an IP address if DHCP has been disabled) or change the domain name. Provision Model Assign Enterprise or Small Business iAMT model. Setup and Configuration Set options to control remote configuration of AMT. Un-Provision Reset the AMT configuration to factory defaults.
Using the HP Universal Print Driver (select models only) The HP Universal Print Driver Series for Windows is a single intelligent driver that replaces individual drivers for HP networked printers. NOTE: The HP Universal Print Driver is preinstalled on select computer models only. To download the HP Universal Print Driver or obtain more information about using it, see the HP Web site at http://www.hp.com/go/universalprintdriver (English only). To print using the HP Universal Print Driver: 1.
Index Symbols/Numerics 1394 cable, connecting 88 1394 devices connecting 88 stopping 88 1394 port identifying 8 using 88 A AC adapter connecting 65 identifying 13 accessory battery connector, identifying 10 Active Management Technology, Intel 146 administrator password 102 airport security devices 78 Altiris Deployment Solutions 142 ambient light sensor hotkey 44 identifying 11 AMT options AMT setup prompt (CTRL-P) 135 firmware progress event support 135 firmware verbosity 135 terminal emulation mode 135 T
volume down 4 volume mute 4, 53 volume up 4 C cables 1394 88 LAN 39 modem 34 USB 86 calibrating battery 71 caps lock light, identifying 3 CD protecting 55 writing to 55 CD drive 89 Certificate of Authenticity label 14 changing boot order 140 charge level indicator, identifying 10 charging batteries 68, 71 checking audio functions 56 components additional hardware 13 bottom 10 display 11 front 6 left-side 8 rear 9 right-side 7 top 1 composite video 43 computer information 118 Computer Setup BIOS administrato
fn key identifying 5 using 2 function keys identifying 5 using 42 H hard disk drive HP 3D DriveGuard 80 installing 83 replacing 82 hard disk test 132 hard drive external 89 HP 3D DriveGuard 80 installing 83 replacing 82 hard drive bay, identifying 10 hard drive recovery 127 HDMI 43 headphone (audio-out) combo jack 7 Hibernation exiting 63 initiated during critical battery level 70 initiating 63 hinge, convertible 11, 15 holder, pen 16 hotkeys ambient light sensor 44 battery charge information 44 decreasing
M maintenance Disk Cleanup 79 Disk Defragmenter 79 McAfee Total Protection 111, 112 Media Card Reader, identifying 8 memory module adding 98 inserting 99 removing 98 replacing 98 memory test 132 microphone (audio-in) combo jack 7 microphone, internal 11 Microsoft Certificate of Authenticity label 14 minimizing interference 33 modem approval label 14 modem cable connecting 34 country-specific cable adapter 34 noise suppression circuitry 34 modem cable adapter, identifying 13 modem cable, identifying 13 modem
rotate button 9, 15 run-in test 132 S S-Video 43 SATA (Serial Advanced Technology Attachment) devices AHCI (Advanced Host Controller Interface) 133 IDE (Integrated Drive Electronics) 133 screen brightness hotkeys 44 screen image, switching 43 scroll zone, TouchPad 2 Secondary Battery Fast Charge 134 security cable slot, identifying 7 Security menu allow reset of HP ProtectTools security keys 131 always prompt for HP SpareKey enrollment 131 Automatic DriveLock 132 change password 131 Disk Sanitizer 132 Drive
volume mute button, identifying 4, 53 volume mute light, identifying 3 volume up button, identifying 4 volume up light, identifying 4 volume, adjusting 53 W Web sites HP System Software Manager 145 HP Universal Print Driver 148 Intel Centrino Pro 146 Intel Pro technology for AMT 146 webcam capturing business cards 60 identifying 11 tips 59 using 59 webcam light, identifying 6, 11 webcam properties, adjusting 59 Windows 7 operating system DVD 127 Windows applications key, identifying 5 Windows logo key, iden
Antenna House XSL Formatter (Evaluation) http://www.antennahouse.
