Getting Started HP Notebook
© Copyright 2011 Hewlett-Packard Development Company, L.P. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
iv Safety warning notice
Table of contents 1 Welcome .......................................................................................................................................................... 1 What's new? ......................................................................................................................................... 2 Finding information ...............................................................................................................................
Using the embedded numeric keypad ............................................................... 24 Turning the embedded numeric keypad on and off .......................... 26 Switching key functions on the embedded numeric keypad ............. 26 Using an optional external numeric keypad ...................................................... 26 Rotating the display ............................................................................................................................
Using a Windows 7 operating system DVD (purchased separately) ................. 50 Windows Vista .................................................................................................................................... 51 Backing up your information .............................................................................................. 51 Performing a recovery .......................................................................................................
viii
1 Welcome ● What's new? ● Finding information After you set up and register the computer, it is important to take the following steps: ● Connect to the Internet—Set up your wired or wireless network so that you can connect to the Internet. For more information, refer to Networking on page 18. ● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer and includes a limited subscription for free updates.
What's new? 2 Chapter 1 Welcome
Finding information The computer comes with several resources to help you perform various tasks. Resources For information about Quick Setup poster ● How to set up the computer ● Help to identify computer components Getting Started ● Computer features To access this guide: ● How to connect to a wireless network specifications Select Start > Help and Support > User Guides.
Resources For information about Safety & Comfort Guide ● Proper workstation setup, posture, health, and work habits To access this guide: ● Electrical and mechanical safety information Select Start > Help and Support > User Guides. – or – Select Start >All Programs > HP > HP Documentation. – or – Go to http://www.hp.com/ergo. Worldwide Telephone Numbers booklet HP support telephone numbers This booklet is provided with your computer.
2 Getting to know your computer ● Top ● Front ● Right ● Left ● Display ● Rear ● Bottom Top TouchPad Top 5
Component Description (1) Pointing stick Moves the pointer and selects or activates items on the screen. (2) Left pointing stick button Functions like the left button on an external mouse. (3) TouchPad Moves the pointer and selects or activates items on the screen. (4) Left TouchPad button Functions like the left button on an external mouse. (5) Right pointing stick button Functions like the right button on an external mouse. (6) TouchPad zone Scrolls up or down.
Component Description (4) Volume down light Blinking: The volume scroll zone is being used to decrease speaker volume. (5) Volume up light Blinking: The volume scroll zone is being used to increase speaker volume (6) Num lock light On: Num lock is on or the embedded numeric keypad is enabled. (7) Drive light ● Blinking turquoise: The hard drive or optical drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. ● Amber: A battery is charging.
Buttons Component 8 Description (1) Volume mute button Mutes and restores speaker sound. (2) Volume down button Decreases computer volume. (3) Volume up button Increases computer volume.
Keys Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Start key Displays the Start menu. (4) Menu key Displays the active program’s shortcut menu (same as right-click menu).
Front Component Description (1) Webcam light On: The webcam is in use. (2) External WWAN antenna button Opens the external wireless wide area network (WWAN) antenna. (3) External WWAN antenna Sends and receives wireless signals to communicate with WWANs. (4) Power switch ● When the computer is off, slide the switch to the right to turn on the computer. ● When the computer is on, slide the switch to the right to shut down the computer.
Right Component Description (1) HP Fingerprint Sensor (fingerprint reader) Allows a fingerprint logon to Windows instead of a password logon. (2) QuickWeb button ● When the computer is off or in Hibernation, press the button to open HP QuickWeb. ● When the computer is in Microsoft Windows, press the button to open the default Web browser. ● When the computer is in HP QuickWeb, press the button to open the default Web browser.
Left Component (1) Description Media Card Reader Supports the following digital card formats: ● MultiMediaCard ● Secure Digital (SD) Card (2) Pen holder Stores the digitizer pen. (3) Vent Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation. (4) Express card slot (select models only) Supports optional ExpressCards.
Display Component Description (1) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWAN). (2) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). (3) Webcam light On: The webcam is in use. (4) Webcam Records video and captures still photographs. To use the webcam, select Start > All Programs > HP > HP Webcam.
Rear Component (1) Description Jog dial In tablet mode, functions like the enter key and the up and down arrows on a standard keyboard. ● Press inward to enter a command. ● Rotate up to scroll up. ● Rotate down to scroll down. (2) esc button In tablet mode, allows you to exit or escape out of an application. (3) Rotate button In tablet mode, switches the image between landscape and portrait orientation.
Bottom Component Description (1) Battery bay Holds the battery. (2) SIM slot Contains a wireless subscriber identity module (SIM). The SIM slot is located inside the battery bay. (3) Vents (3) Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
3 HP QuickWeb ● Starting HP QuickWeb The HP QuickWeb environment provides a fun and engaging way to perform many of your favorite activities. Your computer is ready to go within seconds of starting QuickWeb, allowing you to rapidly access the Internet, widgets, and communication programs. Simply press the QuickWeb button on your computer, and then start browsing the Internet, communicating with Skype, and exploring other HP QuickWeb programs.
Starting HP QuickWeb ▲ To start HP QuickWeb, press the QuickWeb button when the computer is off or in Hibernation. The following table explains the different behaviors of the QuickWeb button. Button Behavior QuickWeb button ● When the computer is off or in Hibernation, opens HP QuickWeb. ● When the computer is in Microsoft Windows, opens the default Web browser. ● When the computer is in HP QuickWeb, opens the default Web browser.
4 Networking ● Using an Internet service provider (ISP) ● Connecting to a wireless network NOTE: Internet hardware and software features vary depending on computer model and your location. Your computer may support one or both of the following types of Internet access: 18 ● Wireless—For mobile Internet access, you can use a wireless connection. Refer to Connecting to an existing WLAN on page 19 or Setting up a new WLAN network on page 20.
Using an Internet service provider (ISP) Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service. NOTE: Your ISP will give you a user ID and password to access the Internet. Record this information and store it in a safe place.
3. Click the network icon in the notification area, at the far right of the taskbar. 4. Select a network to connect to. 5. Click Connect. 6. If required, enter the security key. Setting up a new WLAN network Required equipment: ● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider (ISP) ● A wireless router (purchased separately) (2) ● Your new wireless computer (3) NOTE: Some modems have a built-in wireless router.
Configuring a wireless router For help in setting up a WLAN, refer to the information provided by your router manufacturer or your ISP. The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network: ● Windows 7—Select Start > Control Panel > Network and Internet > Network and Sharing Center > Set up a new connection or network > Set up a network. Then follow the on-screen instructions.
5 22 Keyboard and pointing devices ● Using the keyboard ● Rotating the display ● Using pointing devices ● Using touch screen gestures Chapter 5 Keyboard and pointing devices
Using the keyboard Identifying the hotkeys A hotkey is a combination of the fn key (1) and either the esc key (2) or one of the function keys (3). To use a hotkey: ▲ Briefly press the fn key, and then briefly press the second key of the hotkey combination. Hotkey combination Description fn+esc Displays system information. fn+f3 Initiates Sleep, which saves your information in system. The display and other system components turn off and power is conserved.
Hotkey combination Description fn+f9 Decreases the screen brightness level. fn+f10 Increases the screen brightness level. fn+f11 Activates and deactivates the ambient light. When activated, the ambient light sensor automatically adjusts the display brightness based on the lighting conditions in your environment. Using keypads The computer includes either an embedded numeric keypad or an integrated numeric keypad.
(2) Component Description Embedded numeric keypad When the keypad is turned on, it can be used like an external numeric keypad. Each key on the keypad performs the function indicated by the icon in the upper-right corner of the key. (3) num lk key Turns the embedded numeric keypad on and off when pressed in combination with the fn key. NOTE: The keypad function that is active when the computer is turned off is reinstated when the computer is turned back on.
Turning the embedded numeric keypad on and off Press fn+num lk to turn on the embedded numeric keypad. Press fn+num lk again to turn off the keypad. NOTE: The embedded numeric keypad is turned off while an external keyboard or numeric keypad is connected to the computer.
Rotating the display To use the computer in slate mode: 1. Open the display. 2. Rotate the display 180 degrees either clockwise or counterclockwise. CAUTION: To reduce the risk of damage to your computer, do not force the display past 180 degrees.
3. Lower the display over the keyboard. CAUTION: To reduce the risk of damage to your computer, do not transport the computer while it is in slate mode. Using pointing devices NOTE: In addition to the pointing devices included with your computer, you can use an external USB mouse (purchased separately) by connecting it to one of the USB ports on the computer.
NOTE: If you are using the TouchPad to move the pointer, you must lift your finger off the TouchPad before moving it to the scroll zone. Simply sliding your finger from the TouchPad to the scroll zone does not activate the scrolling function.
Turning the TouchPad off and on To turn the TouchPad off and on, quickly double-tap the TouchPad light. NOTE: The TouchPad light is off when the TouchPad is on. Navigating To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
Selecting Use the left and right TouchPad buttons like the corresponding buttons on an external mouse. Using TouchPad gestures The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the TouchPad at the same time. NOTE: TouchPad gestures are not supported in all programs. To view the demonstration of a gesture: 1. Right-click the Synaptics icon in the notification area, at the far right of the taskbar, and then click TouchPad Properties. 2.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. NOTE: Two-finger scrolling is enabled at the factory. Pinching/Zooming Pinching allows you to zoom in or out on images or text. ● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
Rotating Rotating allows you to rotate items such as photos. To rotate, anchor your left forefinger in the TouchPad zone. Move the right forefinger around the anchored finger in a sweeping motion, moving from 12 o’clock to 3 o’clock. To reverse the rotation, move your right forefinger from 3 o’clock to 12 o’clock. NOTE: Rotating must be done within the TouchPad zone. NOTE: Rotating is disabled at the factory.
Storing the pen To store the pen when you are not using it, insert the pen, tip first, into the pen holder on the computer. Using touch screen gestures You can use your fingers or the digitizer pen on the touch screen. To modify gestures on the touch screen: ▲ Select Start > Control Panel > Hardware and Sound > Pen and Touch. NOTE: Not all gestures are supported in all programs.
Flicking Touch the screen in a light, quick flicking motion up, down, left, or right to navigate through screens or quickly scroll through documents. NOTE: For the flick movement to work, a scrollbar must be present in the active window. Dragging Press your finger on an item on the screen, and then move your finger to drag the item to a new location. You can also use this motion to slowly scroll through documents.
Scrolling Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the screen, and then drag them across the screen in an up, down, left, or right motion. NOTE: Scrolling speed is controlled by finger speed. Rotating Rotating allows you rotate items such as photos. To rotate, anchor your thumb on the screen, and then move your forefinger in a semicircular motion around your thumb.
Pinching/Zooming Pinching allows you to zoom in or out an item. ● Zoom in by holding two fingers together on the screen, and then pull the fingers apart. ● Zoom out by holding two fingers apart on the screen, and then pull the fingers together. Setting touch screen preferences ▲ To set preferences, select Start > Control Panel > Hardware and Sound > Pen and Touch. These preferences are specific to the touch screen and the computer.
6 Maintenance ● Inserting or removing the battery ● Replacing or upgrading the hard drive ● Adding or replacing memory modules ● Updating programs and drivers Inserting or removing the battery NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide. To insert the battery: ▲ Insert the battery (1) into the battery bay until it is seated. The battery release latch (2) automatically locks the battery into place.
2. Remove the battery from the computer (2).
Replacing or upgrading the hard drive CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. Removing the hard drive 40 1.
7. Lift the hard drive (3) out of the hard drive bay. Installing a hard drive 1. Insert the hard drive into the hard drive bay (1). 2. Pull the hard drive tab (2) to the right until the hard drive snaps into place (3). 3. Align the tabs (1) on the service cover with the notches on the computer. 4. Close the cover (2).
5. Tighten the hard drive cover screws (3). 6. Replace the battery. 7. Connect AC power and external devices to the computer. 8. Turn on the computer. Adding or replacing memory modules The computer has two memory module compartments. The capacity of the computer can be upgraded by adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory module in the primary memory module slot.
CAUTION: To prevent information loss or an unresponsive system: Shut down the computer before adding or replacing memory modules. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation. If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system. 1. Save your work and shut down the computer. 2.
b. Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot. CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module. To protect a memory module after removal, place it in an electrostatic-safe container. 7. Insert a new memory module: CAUTION: To prevent damage to the memory module, hold the memory module by the edges only.
8. Align the tabs (1) on the service cover with the notches on the computer. 9. Close the cover (2). 10. Tighten the hard drive cover screws (3). 11. Replace the battery. 12. Connect AC power and external devices to the computer. 13. Turn on the computer.
Updating programs and drivers HP recommends that you update your programs and drivers on a regular basis with the latest versions. Go to http://www.hp.com/support to download the latest versions. You can also register to receive automatic update notifications when they become available.
7 Backup and recovery Windows 7 ● Backing up your information ● Performing a system recovery To protect your information, use Windows Backup and Restore to back up individual files and folders, back up your entire hard drive (select models only), create system repair discs (select models only) by using the installed optical drive (select models only) or an optional external optical drive, or create system restore points.
new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup. The system repair discs (select models only) are used to start up (boot) the computer and repair the operating system in case of system instability or failure. Your initial and subsequent backups allow you to restore your data and settings if a failure occurs. You can back up your information to an optional external hard drive, a network drive, or discs.
Using the Windows recovery tools To recover information you previously backed up: 1. Select Start > All Programs > Maintenance > Backup and Restore. 2. Follow the on-screen instructions to recover your system settings, your computer (select models only), or your files. To recover your information using Startup Repair, follow these steps: CAUTION: Using Startup Repair completely erases hard drive contents and reformats the hard drive.
3. If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC key for Startup Menu” message is displayed at the bottom of the screen. 4. Press f11 while the “Press for recovery” message is displayed on the screen. 5. Follow the on-screen instructions. Using a Windows 7 operating system DVD (purchased separately) To order a Windows 7 operating system DVD, go to http://www.hp.
Windows Vista To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
To create a backup using Backup and Restore Center: NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Select Start > All Programs > Maintenance > Backup and Restore Center. 2. Follow the on-screen instructions to back up your entire computer (select models only) or your files.
4. Select Repair your computer. 5. Follow the on-screen instructions. NOTE: For additional information on recovering information using the Windows tools, perform a search for these topics in Help and Support. Using f11 recovery tools CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files you have created and any software installed on the computer are permanently removed.
NOTE: 54 This process takes several minutes. 1. If possible, back up all personal files. 2. Restart the computer, and then insert the Windows Vista operating system DVD into the optical drive before the Windows operating system loads. 3. When prompted, press any keyboard key. 4. Follow the on-screen instructions. 5. Click Next. 6. Select Repair your computer. 7. Follow the on-screen instructions.
8 Customer support ● Contacting customer support ● Labels 55
Contacting customer support If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.html. Here you can: ● Chat online with an HP technician.
Labels The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer: ● Serial number label—Provides important information, including the following: Component (1) Product name (2) Serial number (s/n) (3) Part number/Product number (p/n) (4) Warranty period (5) Model description Have this information available when you contact technical support. The serial number label is affixed to the bottom of the computer.
9 58 Specifications ● Input power ● Operating environment Chapter 9 Specifications
Input power The power information in this section may be helpful if you plan to travel internationally with the computer. The computer operates on DC power, which can be supplied by an AC or a DC power source. The AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
Operating environment Factor Metric U.S.
Index Symbols/Numerics 1394 port, identifying 12 A Accessory battery connector identifying 15 Accessory battery connector door identifying 15 Ambient light sensor, identifying 13 ambient light, hotkey 24 audio-in (microphone) jack, identifying 11 audio-out (headphone) jack, identifying 11 D display image, switching 23 display release latch 10 display, rotating 27 Docking connector identifying 15 dragging touch screen gesture 35 drive light 7 B Backup and Restore 48 Backup and Restore Center 51, 52 batt
network 14 RJ-11 (modem) 11 RJ-45 (network) 14 jog dial, identifying 14 K keyboard hotkeys, identifying 23 Keyboard light button Identifying 13 keypad, embedded numeric 9 keypad, external num lock 26 using 26 keypads, identifying 24 keys esc 9 fn 9, 24 function 9 Menu 9 Start 9 L labels Bluetooth 57 HP Mobile Broadband Module 57 Microsoft Certificate of Authenticity 57 regulatory 57 serial number 57 SIM 57 wireless certification 57 WLAN 57 latch, battery release 15 lights battery 7 caps lock 6 drive 7 mute
flicking 35 pinching 37 rotating 36 scrolling 36 tapping 34 zooming 37 TouchPad buttons 6 using 28 TouchPad gestures pinching 32 rotating 33 scrolling 32 zooming 32 TouchPad light, identifying 6 TouchPad zone, identifying 6 TouchPad, identifying 6 traveling with the computer 57 wireless set up 20 Wireless switch Identifying 12 WLAN connecting 19 protecting 21 WLAN antennas, identifying 13 WLAN device 57 WLAN label 57 WWAN antennas, identifying 13 Z zooming screen gesture 37 zooming TouchPad gesture 32 U U
