Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysLogicGate Optocoupler SO 8 Type (misc.) 5 MBd, 1-channel

Description

The HCPL-22XX, HCPL-02XX, and HCNW22XX are optical-

ly-coupled logic gates. The HCPL-22XX, and HCPL-02XX

contain a GaAsP LED while the HCNW22XX contains an

AlGaAs LED. The detectors have totem pole output stag-

es and optical receiver input stages with built-in Schmitt

triggers to provide logic-compatible waveforms, eliminat-

ing the need for additional waveshaping.

A superior internal shield on the HCPL-2211/12, HCPL-

0211, HCPL-2232 and HCNW2211 guarantees common

mode transient immunity of 10 kV/µs at a common

mode voltage of 1000 volts.

Functional Diagram

CAUTION: It is advised that normal static precautions be taken in handling and assembly

of this component to prevent damage and/or degradation which may be induced by ESD.

A 0.1 µF bypass capacitor must be connected between pins 5 and 8.

ANODE

CATHODE

NC GND

SHIELD

HCPL-2201/11

HCPL-0201/11

HCNW2201/11

HCPL-2201 Functional Diagram

ANODE

CATHODE

NC GND

SHIELD

HCPL-2202/12

ANODE 1

CATHODE 1

CATHODE 2

ANODE 2 GND

SHIELD

HCPL-2231/32

TRUTH TABLE

(POSITIVE LOGIC)

LED

OFF

HIGH

LOW

HCPL-2201, HCPL-2202, HCPL-2211,HCPL-2212,

HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211,

HCNW2201, HCNW2211

Very High CMR, Wide V

Logic Gate Optocouplers

Data Sheet

Features

• 10 kV/µs minimum Common Mode Rejection

(CMR) at V

= 1000 V (HCPL-2211/2212/0211/2232,

HCNW2211)

• Wide operating V

range: 4.5 to 20 Volts

• 300 ns propagation delay guaranteed over the full

temperature range

• 5 Mbd typical signal rate

• Low input current (1.6 mA to 1.8 mA)

• Hysteresis

• Totem pole output (no pullup resistor required)

• Available in 8-Pin DIP, SOIC-8, widebody packages

• Guaranteed performance from -40°C to 85°C

• Safety approval

– UL recognized -3750 V rms for 1 minute (5000 V

rms for 1 minute for HCNW22XX) per UL1577

– CSAapproved

– IEC/EN/DIN EN 60747-5-2 approved with V

IORM

630 V

peak

(HCPL-2211/2212 Option 060 only) and

IORM

= 1414 V

peak

(HCNW22XX only)

• MIL-PRF-38534 hermetic version available

(HCPL-52XX/62XX)

Applications

• Isolation of high speed logic systems

• Computer-peripheral interfaces

• Microprocessor system interfaces

• Ground loop elimination

• Pulse transformer replacement

• High speed line receiver

• Power control systems

Lead (Pb) Free

RoHS 6 fully

compliant

RoHS 6 fully compliant options available;

-xxxE denotes a lead-free product

Summary of content (18 pages)

PAGE 1
HCPL-2201, HCPL-2202, HCPL-2211,HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211, HCNW2201, HCNW2211 Very High CMR, Wide VCC Logic Gate Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features The HCPL-22XX, HCPL-02XX, and HCNW22XX are optically-coupled logic gates. The HCPL‑22XX, and HCPL-02XX contain a GaAsP LED while the HCNW22XX contains an AlGaAs LED.
PAGE 2
The electrical and switching characteristics of the HCPL22XX, HCPL-02XX and HCNW22XX are guaranteed from -40°C to +85°C and a VCC from 4.5 volts to 20 volts. Low IF and wide VCC range allow compatibility with TTL, LSTTL, and CMOS logic and result in lower power consumption compared to other high speed couplers. Logic signals are transmitted with a typical propagation delay of 150 ns.
PAGE 3
Ordering Information HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW2201 and HCNW2211 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All devices listed above are approved under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 4
Package Outline Drawings 8-Pin DIP Package (HCPL-2201/02/11/12/31/32) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 8 TYPE NUMBER 7 6 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* DATE CODE A XXXXZ YYWW RU 1 2 3 4 UL RECOGNITION 1.78 (0.070) MAX. 1.19 (0.047) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 5° TYP. 3.56 ± 0.13 (0.140 ± 0.005) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. 1.080 ± 0.320 (0.043 ± 0.013) DIMENSIONS IN MILLIMETERS AND (INCHES).
PAGE 5
Small-Outline SO-8 Package (HCPL-0201/11) LAND PATTERN RECOMMENDATION 8 7 6 5 5.994 ± 0.203 (0.236 ± 0.008) XXX YWW 3.937 ± 0.127 (0.155 ± 0.005) 7.49 (0.295) TYPE NUMBER (LAST 3 DIGITS) DATE CODE 1 PIN ONE 2 3 4 1.9 (0.075) 0.406 ± 0.076 (0.016 ± 0.003) 1.270 BSC (0.050) 0.64 (0.025) * 5.080 ± 0.127 (0.200 ± 0.005) 7o 3.175 ± 0.127 (0.125 ± 0.005) 1.524 (0.060) 0.432 (0.017) 45o X 0 ~ 7o * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) 0.228 ± 0.
PAGE 6
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11) 11.15 ± 0.15 (0.442 ± 0.006) 8 7 6 LAND PATTERN RECOMMENDATION 5 9.00 ± 0.15 (0.354 ± 0.006) 1 2 3 13.56 (0.534) 4 2.29 (0.09) 1.3 (0.051) 12.30 ± 0.30 (0.484 ± 0.012) 1.55 (0.061) MAX. 11.00 MAX. (0.433) 4.00 MAX. (0.158) 1.78 ± 0.15 (0.070 ± 0.006) 0.75 ± 0.25 (0.030 ± 0.010) 2.54 (0.100) BSC 1.00 ± 0.15 (0.039 ± 0.006) + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.002) DIMENSIONS IN MILLIMETERS (INCHES).
PAGE 7
Recommended Pb-Free IR Profile tp Tp TEMPERATURE TL Tsmax * 260 +0/-5 °C TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATURE 15 SEC. 217 °C 150 - 200 °C RAMP-UP 3 °C/SEC. MAX. NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 °C, Tsmin = 150 °C RAMP-DOWN 6 °C/SEC. MAX. Tsmin ts PREHEAT 60 to 180 SEC. 25 tL NOTE: NON-HALIDE FLUX SHOULD BE USED. 60 to 150 SEC.
PAGE 8
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-2211/2212 Option 060 ONLY) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤300 V rms I-IV for rated mains voltage ≤450 V rms I-III Climatic Classification 55/85/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage VIORM 630 V peak Input to Output Test Voltage, Method b* VIORM x 1.
PAGE 9
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW22XX ONLY) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤600 V rms I-IV for rated mains voltage ≤1000 V rms I-III Climatic Classification 55/100/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage VIORM 1414 V peak Input to Output Test Voltage, Method b* VIORM x 1.
PAGE 10
Absolute Maximum Ratings Parameter Symbol Min. Max. Units Storage Temperature TS -55 125 °C Operating Temperature TA -40 85 °C Note Average Forward Input Current IF(AVG) 10 mA 1 Peak Transient Input Current (≤ 1 µs Pulse Width, 300 pps) IF(TRAN) 1.
PAGE 11
Electrical Specifications -40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specified. All Typicals at TA = 25°C. See Note 7. Parameter Sym. Min. Typ. Logic Low Output Voltage VOL Logic High Output Voltage VOH (VOUT > VCC) Output Leakage Current 2.4 0.5 ** Units IOHH ICCL 3.7 100 Test ConditionsFig. IOL = 6.4 mA (4 TTL Loads) 1, 3 1 V IOH = -2.6 mA 2, 3, 1 µA IOH = -0.4 mA VO = 5.
PAGE 12
Switching Specifications (AC) -40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V. All Typicals at TA = 25°C, VCC = 5 V, IF(ON) = 3 mA unless otherwise specified. Parameter Sym. Min. Propagation Delay Time tPHL Typ. Max.
PAGE 13
Package Characteristics Parameter Sym. Min. Input-Output Momentary VISO 3750 Withstand Voltage* HCNW22XX Input-Output Resistance Input-Output Capacitance Max. Units Test Conditions V rms 5000 RI-O HCNW22XX Typ. 1012 1012 1011 CI-O HCNW22XX 0.6 0.5 5, 10 TA = 25°C 5, 11 VI-O = 500 Vdc 5 f = 1 MHz, 5 TA = 25°C TA = 100°C pF 0.6 Note RH < 50%, t = 1 min. Ω 1013 Fig.
PAGE 14
IOH – HIGH LEVEL OUTPUT CURRENT – mA VCC = 4.5 V VF = 0 V IO = 6.4 mA 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -60 -40 -20 0 20 40 60 80 100 0 5 VCC = 4.5 V IF = 5 mA -1 -2 VO = 2.7 V -3 -4 -5 VO = 2.4 V -6 -7 -8 -60 -40 -20 TA – TEMPERATURE – °C IF – FORWARD CURRENT – mA IF – FORWARD CURRENT – mA 1.0 0.1 0.01 1.2 1.3 60 4 3 IO = -2.6 mA 2 1 0 80 100 IO = 6.4 mA 0 0.5 1.4 1.5 Figure 3. Typical output voltage vs. forward input current.
PAGE 15
250 VCC = 5.0 V, 20 V C1 (120 pF) PEAKING CAPACITOR IS USED. SEE FIGURE 5. 200 *IF = 1.8 mA FOR HCPL-223X DEVICES. tP – PROPAGATION DELAY – ns tP – PROPAGATION DELAY – ns 250 IF (mA) 5 3 1.6* 150 1.6* -5 tPHL 100 tPLH 50 -60 -40 -20 0 20 40 60 HCNW22XX IF (mA) 5 200 3 150 1.6 tPHL 1.6, 5 100 tPLH 50 -60 -40 -20 80 100 80 VCC = 5.0 V, 20 V C1 (120 pF) PEAKING CAPACITOR IS USED. SEE FIGURE 5.
PAGE 16
HCPL-22XX HCPL-02XX VCC = 5.0 V VCC = 20 V 0.9 0.8 IF (ON) 0.7 IF (OFF) 0.6 IF (ON) IF (OFF) 0.5 -60 -40 -20 0 20 40 HCNW22XX 1.0 INPUT CURRENT THRESHOLD – mA INPUT CURRENT THRESHOLD – mA 1.0 60 80 100 VCC = 5.0 V VCC = 20 V 0.9 0.8 0.7 IF (ON) IF (OFF) 0.6 IF (ON) IF (OFF) 0.5 -60 -40 -20 0 20 40 60 80 100 TA – TEMPERATURE – °C TA – TEMPERATURE – °C Figure 11. Typical input threshold current vs. temperature.
PAGE 17
HCPL-2201/11 HCPL-02XX HCNW22XX 80 Ω VCC1 (+5 V) 120 pF 1.1 kΩ DATA INPUT TTL OR LSTTL VCC2 (+5 V) 1 8 2 7 3 6 4 5 1 DATA OUTPUT * UP TO 16 LSTTL LOADS OR 4 TTL LOADS * 0.1 µF BYPASS 2 Figure 13b. Recommended LSTTL to LSTTL circuit for applications requiring a maximum allowable propagation delay of 300 ns. HCPL-2201 fig 13b VCC2 (4.5 TO 20 V) HCPL-2201/11 HCPL-02XX HCNW22XX 80 Ω* VCC1 (+5 V) 1.
PAGE 18
For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2005-2008 Avago Technologies Limited. All rights reserved.