Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysTransistor-Output-Optocoupler SO 8 Type (misc.) 1 MBd, 1-channel

Description

These diode-transistor optocouplers use an insulating

layer between a LED and an integrated photodetector to

provide electrical insulation between input and output.

Separate connections for the photodiode bias and out-

put-transistor collector increase the speed up to a hun-

dred times that of a conventional phototransistor coupler

by reducing the base-collector capacitance.

These single channel optocouplers are available in

8-Pin DIP, SO-8 and Widebody package congurations.

The 6N135, HCPL-0500, and HCNW135 are for use in TTL/

CMOS, TTL/LSTTL or wide bandwidth analog applications.

Current transfer ratio (CTR) for these devices is 7% mini-

mum at I

= 16 mA.

The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are

designed for high speed TTL/TTL applications. A standard

16 mA TTL sink current through the input LED will pro-

vide enough output current for 1 TTL load and a 5.6 kΩ

pull-up resistor. CTR for these devices is 19% minimum at

= 16 mA.

Functional Diagram

A 0.1 µF bypass capacitor must be connected between pins 5 and 8.

6N135/6, HCNW135/6, HCNW4502/3

HCPL-2502/0452/0453/0500/0501/4502/4503

Single Channel, High Speed Optocouplers

Data Sheet

Features

• 15 kV/µs minimum common mode transient

immunity at V

= 1500 V (4503/0453)

• High speed: 1 Mb/s

• TTL compatible

• Available in 8-Pin DIP, SO-8, widebody packages

• Open collector output

• Guaranteed performance from temperature:

0°C to 70°C

• Safety approval

UL Recognized – 3750 V

rms

for 1 minute (5000 V

rms

for 1 minute for HCNW and Option 020 devices)

per UL1577

CSA Approved

IEC/EN/DIN EN 60747-5-2 Approved

– V

IORM

= 630 V peak for HCPL-4503#060

– V

IORM

= 1414 V peak for HCNW devices

• Dual channel version available

(253X/4534/053X/0534)

• MIL-PRF-38534 hermetic version available

(55XX/65XX/4N55)

Applications

• High voltage insulation

• Video signal isolation

• Power transistor isolation in motor drives

• Line receivers

• Feedback element in switched mode power supplies

• High speed logic ground isolation

– TTL/TTL, TTL/CMOS, TTL/LSTTL

• Replaces pulse transformers

• Replaces slow phototransistor isolators

• Analog signal ground isolation

Lead (Pb) Free

RoHS 6 fully

compliant

RoHS 6 fully compliant options available;

-xxxE denotes a lead-free product

ANODE

CATHODE

GND

* NOTE: FOR 4502/3, 0452/3,

PIN 7 IS NOT CONNECTED.

TRUTH TABLE

(POSITIVE LOGIC)

LED

OFF

LOW

HIGH

CAUTION: It is advised that normal static precautions be taken in handling and assembly

of this component to prevent damage and/or degradation which may be induced by ESD.

Summary of content (17 pages)

PAGE 1
6N135/6, HCNW135/6, HCNW4502/3 HCPL-2502/0452/0453/0500/0501/4502/4503 Single Channel, High Speed Optocouplers Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product Description Features These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output.
PAGE 2
The HCPL-4502, HCPL-0452, and HCNW4502 provide the electrical and switching performance of the 6N136, HCPL0501, and HCNW136 with increased ESD protection. The HCPL-4503, HCPL-0453, and HCNW4503 are similar to the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers but have increased common mode transient immunity of 15 kV/µs minimum at VCM = 1500 V guaranteed.
PAGE 3
Ordering Information 6N135, 6N136, HCPL-2502, HCPL-4502 and HCPL-4503, HCPL-0452, HCPL-0453, HCPL-0500, HCPL-0501 are UL Recognized with 3750 Vrms for 1 minute per UL1577. HCNW135, HCNW136, HCNW4502 and HCNW4503 are UL Recognized with 5000 Vrms for 1 minute per UL1577. All devices above listed are approved under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 4
Package Outline Drawings 8-Pin DIP Package (6N135/6, HCPL-4502/3, HCPL-2502) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 8 TYPE NUMBER 7 6 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* DATE CODE A XXXXZ YYWW RU 1 2 3 UL RECOGNITION 4 1.78 (0.070) MAX. 1.19 (0.047) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 5° TYP. 3.56 ± 0.13 (0.140 ± 0.005) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES). 0.65 (0.025) MAX. 1.080 ± 0.320 (0.
PAGE 5
Small Outline SO-8 Package (HCPL-0500/1, HCPL-0452/3) LAND PATTERN RECOMMENDATION 8 7 6 5 5.994 ± 0.203 (0.236 ± 0.008) XXX YWW 3.937 ± 0.127 (0.155 ± 0.005) 7.49 (0.295) TYPE NUMBER (LAST 3 DIGITS) DATE CODE PIN ONE 1 2 3 4 1.9 (0.075) 0.406 ± 0.076 (0.016 ± 0.003) 1.270 BSC (0.050) 0.64 (0.025) * 5.080 ± 0.127 (0.200 ± 0.005) 7° 3.175 ± 0.127 (0.125 ± 0.005) 45° X 0.432 (0.017) 0 ~ 7° 1.524 (0.060) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± 0.254 (0.205 ± 0.010) 0.
PAGE 6
8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6, HCNW4502/3) 11.15 ± 0.15 (0.442 ± 0.006) 8 7 LAND PATTERN RECOMMENDATION 6 5 9.00 ± 0.15 (0.354 ± 0.006) 1 2 3 13.56 (0.534) 4 2.29 (0.09) 1.3 (0.051) 12.30 ± 0.30 (0.484 ± 0.012) 1.55 (0.061) MAX. 11.00 MAX. (0.433) 4.00 MAX. (0.158) 1.78 ± 0.15 (0.070 ± 0.006) 2.54 (0.100) BSC 0.75 ± 0.25 (0.030 ± 0.010) 1.00 ± 0.15 (0.039 ± 0.006) + 0.076 0.254 - 0.0051 + 0.003) (0.010 - 0.
PAGE 7
Recommended Pb-Free IR Profile tp Tp TEMPERATURE TL Tsmax * 260 +0/-5 °C TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATURE 15 SEC. 217 °C 150 - 200 °C RAMP-UP 3 °C/SEC. MAX. RAMP-DOWN 6 °C/SEC. MAX. NOTES: THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX. Tsmax = 200 °C, Tsmin = 150 °C Tsmin ts PREHEAT 60 to 180 SEC. 25 tL NON-HALIDE FLUX SHOULD BE USED. 60 to 150 SEC.
PAGE 8
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-4503 Option 060 ONLY) Description Symbol Characteristic Units Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤300 V rms I-IV for rated mains voltage ≤450 V rms I-III Climatic Classification 55/100/21 Pollution Degree (DIN VDE 0110/1.89) 2 Maximum Working Insulation Voltage VIORM 630 V peak Input to Output Test Voltage, Method b* VIORM x 1.
PAGE 9
Absolute Maximum Ratings Parameter Storage Temperature* Symbol Device TS Min. Max.
PAGE 10
Electrical Specifications (DC) Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. See note 13. Parameter Current Transfer Ratio Symbol Device Min. Typ.** Max. Units CTR* 6N135 HCPL-0500 HCNW135 HCPL-2502 7 5 18 19 50 % 15 15 19 15 25 24 25 0.1 0.1 0.4 0.5 0.1 0.1 0.4 0.
PAGE 11
Switching Specifications (AC) Over recommended temperature (TA = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specified. Parameter Sym. Propagation tPHL* Delay Time to Logic Low at Output Propagation tPLH* Delay Time to Logic High at Output Device Min. Typ.** 6N135 0.2 HCPL-0500 HCNW135 Max. Units Test Conditions 1.5 µs TA = 25°C RL = 4.1 kΩ 2.0 6N136 0.2 0.
PAGE 12
Package Characteristics Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. Parameter Sym. Device Min. Typ.* Max. Units Input-Output VISO 8-Pin DIP 3750 V rms Momentary SO-8 Widebody 5000 Withstand Voltage** 8-Pin DIP SO-8 1012 Widebody 1013 Input-Output CI-O Capacitance Fig. RH < 50%, t = 1 min.
PAGE 13
T = 25° C 10 VA = 5.0 V CC 35 mA 30 mA 25 mA 5 20 mA 15 mA 10 mA 0 IF = 5 mA 0 10 WIDEBODY 16 40 mA IO Ð OUTPUT CURRENT Ð mA IO Ð OUTPUT CURRENT - mA 8 PIN DIP, SO-8 40 mA 12 35 mA 30 mA 25 mA 8 20 mA 15 mA 4 10 mA IF = 5 mA 0 20 TA = 25° C VCC = 5.0 V 0 10 VO - OUTPUT VOLTAGE - V 20 VO - OUTPUT VOLTAGE - V 8 PIN DIP, SO-8 1.5 6N135, HCPL-0500 6N136, HCPL-4502/3, HCPL-2502 HCPL-0501/0452/0453 1.0 0.5 0.1 NORMALIZED I F = 16 mA VO = 0.
PAGE 14
1.0 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25° C 0.9 0.8 6N135, HCPL-0500 6N136, HCPL-4502/3, HCPL-2502 HCPL-0501, 0452, 0453 0.7 0.6 -60 -40 -20 0 20 40 60 80 100 NORMALIZED CURRENT TRANSFER RATIO NORMALIZED CURRENT TRANSFER RATIO 8 PIN DIP, SO-8 1.1 WIDEBODY 1.1 1.0 HCNW135/6, HCNW4502/3 0.9 0.8 0.7 NORMALIZED IF = 16 mA VO = 0.4 V VCC = 5 V TA = 25° C 0.6 0.5 0.4 -60 -40 -20 TA - TEMPERATURE - ° C 0 20 40 80 100 60 TA - TEMPERATURE - ° C Figure 4.
PAGE 15
IF = 0 VO = VCC = 5.0 V 10+3 10+2 10+1 100 10 -1 10 -2 -75 -50 -25 0 +25 +50 +75 +100 IOH - LOGIC HIGH OUTPUT CURRENT - nA IOH - LOGIC HIGH OUTPUT CURRENT - nA 8 PIN DIP, SO-8 10+4 WIDEBODY +3 10 IF = 0 VO = VCC = 15 V +2 10 +1 10 0 10 -60 -40 -20 0 20 40 60 80 100 TA - TEMPERATURE - ° C TA - TEMPERATURE - ° C 8 PIN DIP, SO-8 0.30 IO - SMALL SIGNAL CURRENT TRANSFER RATIO I�� F IO - SMALL SIGNAL CURRENT TRANSFER RATIO I F�� Figure 7. Logic high output current vs. temperature.
PAGE 16
NORMALIZED RESPONSE - dB +5 6N135/6, HCPL-0500/1, HCPL-2502 TA = 25 ° C 6N135/6, HCPL-0500/1, HCPL-2502 +12 V 1 0.1 µF 0 2 7 3 6 15 KΩ 1.2 KΩ 47 µF VFF -10 100 Ω 1 KΩ 51 Ω -15 1N4150 1.0 10 Q1 5 TRIM FOR UNITY GAIN 100 HCNW135/6 Figure 10. Frequency response. Q 1 , Q 2 , Q 3 : 2N3904 TYPICAL LINEARITY = ± 3% AT V IN = 1 V p-p TYPICAL SNR = 50dB TYPICAL R T = 375 Ω TYPICAL VO dc = 3.8 V TYPICAL I F = 9 mA f - FREQUENCY - MHz HCNW135/6 470Ω � 100 Ω RT 22 Ω VO Q2 0.1 µF 4 0.
PAGE 17
IF 5V VO 1.5 V 10% DUTY CYCLE 1/f < 100 µS 1.5 V VOL 1 8 2 7 * 3 6 +5 V RL 0.1µF I F MONITOR 4 5 * PIN 7 UNCONNECTED IN HCPL-4502/3, HCPL-0452/3, HCNW4502/3 Figure 11. Switching test circuit. IF 1 8 2 7 * 3 6 +5 V B VCM 0V 10% 90% 90% VO tf 5V SWITCH AT B: I F = 16 mA VO 0.1 µF SWITCH AT A: I F = 0 mA VO RL A 10% tr VFF 4 5 VOL VCM + - PULSE GEN. *PIN 7 UNCONNECTED IN HCPL-4502/3, HCPL-0542/3, HCNW4502/3 Figure 12.