Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysDarlington Transistor-Output Optocoupler SO 8 Type (misc.) 100 kBd, 1-channel

ANODE

CATHODE

GND

HCPL-4701/070A

GND

ANODE

CATHODE

ANODE

TRUTH TABLE

LED

OFF

LOW

HIGH

HCPL-4731/073A

Features

• Ultra low input current capability - 40 µA

• Specified for 3 V operation

Typical power consumption: <1 mW

Input power: <50 µW

Output power: <500 µW

•Will operate with V

as low as 1.6 V

• High current transfer ratio: 3500% at I

= 40 µA

• TTL and CMOS compatible output

• Specified ac and dc performance over temperature:

0°C to 70°C

• Safety approval:

UL recognized – 3750 V rms for 1 minute and

5000 V rms* for 1 minute per UL1577

CSA approved

IEC/EN/DIN EN 60747-5-2 approved with

IORM

= 630 V peak

(Option 060) for HCPL-4701

• 8-pin product compatible with 6N138/6N139 and

HCPL-2730/HCPL-2731

• Available in 8-Pin DIP and SOIC-8 footprint

• Through hole and surface mount assembly available

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to

prevent damage and/or degradation which may be induced by ESD.

Functional Diagram

*5000 V rms/1 Minute rating is for Option 020 (HCPL-4701 and HCPL-4731) products only.

A 0.1 µF bypass capacitor connected between pins 8 and 5 is recommended.

Applications

• Battery operated applications

• ISDN telephone interface

• Ground isolation between logic families – TTL, LSTTL,

CMOS, HCMOS, HL-CMOS, LV-HCMOS

• Low input current line receiver

• EIA RS-232C line receiver

• Telephone ring detector

• AC line voltage status indicator – low input power

dissipation

• Low power systems – ground isolation

• Portable system I/O interface

HCPL-4701/-4731/-070A/-073A

Very Low Power Consumption High Gain Optocouplers

Data Sheet

Summary of content (17 pages)

PAGE 1
HCPL-4701/-4731/-070A/-073A Very Low Power Consumption High Gain Optocouplers Data Sheet Features Applications • Ultra low input current capability - 40 µA • Specified for 3 V operation Typical power consumption: <1 mW Input power: <50 µW Output power: <500 µW • Will operate with VCC as low as 1.
PAGE 2
Description These devices are very low power consumption, high gain single and dual channel optocouplers. The HCPL-4701 represents the single channel 8-Pin DIP configuration and is pin compatible with the industry standard 6N139. The HCPL-4731 represents the dual channel 8-Pin DIP configuration and is pin compatible with the popular standard HCPL-2731. The HCPL-070A and HCPL-073A are the equivalent single and dual channel products in an SO-8 footprint.
PAGE 3
Ordering Information HCPL-4701, HCPL-4731, HCPL-070A and HCPL-073A are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are approved under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 4
Schematic HCPL-4701 and HCPL-070A HCPL-4731 and HCPL-073A VCC 8 1 + ICC 2 ANODE 8 VCC VF1 IF + – VF CATHODE I CC I F1 I O1 VO1 2 – IO 3 6 7 VO 3 IB – 7 VB 5 GND I O2 6 VF2 VO2 SHIELD + 4 I F2 GND 5 SHIELD USE OF A 0.
PAGE 5
Package Outline Drawings 8-Pin DIP Package (HCPL-4701, HCPL-4731) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) 8 TYPE NUMBER 7 6 5 6.35 ± 0.25 (0.250 ± 0.010) OPTION CODE* A XXXXZ DATE CODE YYWW 1 2 3 4 1.78 (0.070) MAX. 1.19 (0.047) MAX. + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 5° TYP. 3.56 ± 0.13 (0.140 ± 0.005) 4.70 (0.185) MAX. 0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS IN MILLIMETERS AND (INCHES).
PAGE 6
Small-Outline SO-8 Package (HCPL-070A, HCPL-073A) LAND PATTERN RECOMMENDATION 8 7 6 5 5.994 ± 0.203 (0.236 ± 0.008) XXX YWW 3.937 ± 0.127 (0.155 ± 0.005) TYPE NUMBER (LAST 3 DIGITS) 7.49 (0.295) DATE CODE PIN ONE 1 2 3 4 1.9 (0.075) 0.406 ± 0.076 (0.016 ± 0.003) 1.270 BSC (0.050) 0.64 (0.025) 7° * 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) 45° X 0.432 (0.017) 0.228 ± 0.025 (0.009 ± 0.001) 1.524 (0.060) 0.203 ± 0.102 (0.008 ± 0.004) 0.305 MIN. (0.
PAGE 7
Recommended Pb-Free IR Profile tp Tp TEMPERATURE TL Tsmax Regulatory Information TIME WITHIN 5 °C of ACTUAL PEAK TEMPERATURE 20-40 SEC. The HCPL-4701/4731 and HCPL070A/073A have been approved by the following organizations: 260 +0/-5 °C UL Recognized under UL 1577, Component Recognition Program, File E55361. 217 °C RAMP-UP 3 °C/SEC. MAX. 150 - 200 °C RAMP-DOWN 6 °C/SEC. MAX. Tsmin ts PREHEAT 60 to 180 SEC. tL 60 to 150 SEC. CSA Approved under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 8
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCPL-4701 OPTION 060 ONLY) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 300 V rms for rated mains voltage ≤ 450 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method b* VIORM x 1.87 = VPR, 100% Production Test with tm = 1 sec, Partial Discharge < 5 pC Input to Output Test Voltage, Method a* VIORM x 1.
PAGE 9
Absolute Maximum Ratings (No Derating Required up to 70°C) Parameter Symbol Minimum Maximum Units Storage Temperature TS -55 125 °C Operating Temperature TA -40 85 °C Average Forward Input Current (HCPL-4701/4731) IF(AVG) 10 mA Average Forward Input Current (HCPL-070A/073A) IF(AVG) 5 mA Peak Transient Input Current (HCPL-4701/4731) (50% Duty Cycle, 1 ms Pulse Width) IFPK 20 mA Peak Transient Input Current (HCPL-070A/073A) (50% Duty Cycle, 1 ms Pulse Width) IFPK 10 mA Reverse I
PAGE 10
Electrical Specifications 0°C ≤ TA ≤ 70°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON) ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specified. All Typicals at TA = 25°C. See note 8.
PAGE 11
Switching Specifications (AC) Over Recommended Operating Conditions TA = 0°C to 70°C, VCC = 3 V to 18 V, unless otherwise specified. Parameter Device HCPL- Symbol Propagation Delay Time to Logic Low at Output tPHL Propagation Delay Time to Logic High Output tPLH Min. Typ.* Max. Units 65 500 3 25 30 70 500 34 60 90 130 4701/4731 070A/073A Test Conditions Fig. Note µs IF = 40 µA, RL = 11 to 16 kΩ, VCC = 3.3 to 5 V IF = 0.5 mA, TA = 25°C RL = 4.
PAGE 12
detection current limit, II-O ≤ 5 µA. This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table. 5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. 6. Common transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common mode pulse, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V).
PAGE 13
VCM 10 V 90% 90% 10% 0V IF tf VO RCC (SEE NOTE 7) +5 V 220 Ω 2 7 0.1 µF 3 6 4 5 RL A VO VFF 5V SWITCH AT A: IF = 0 mA VO 8 B 10% tr 1 VCM + – VOL SWITCH AT B: IF = 0.5 mA PULSE GEN. Figure 8. Test Circuit for Transient Immunity and Typical Waveforms. IF 0 5V VO (SATURATED RESPONSE) 1.5 V 1.5 V t PHL PULSE GEN. Z O = 50 Ω t r = 5 ns IF 10% DUTY CYCLE 1/f < 100 µs 1 8 2 7 3 6 VOL t PLH +5 V RL VO 0.1 µF I F MONITOR 4 5 * CL = 15 pF RM Figure 9.
PAGE 14
Table 1. Typical HCPL-4701 Power Dissipation for 3 V and 5 V Applications Power Dissipation (µW) PLED PVcc PO-C[1] PTOTAL[2] VCC = 3.3 Vdc IF = 40 µA IF = 500 µA 50 625 65 330 20 10 135 µW 965 µW VCC = 5 Vdc IF = 40 µA IF = 500 µA 50 625 100 500 25 20 175 µW 1,145 µW Notes: 1. RL of 11 kΩ open-collector (o-c) pull-up resistor was used for both 3.3 Vdc and 5 Vdc calculations. 2. For typical total interface circuit power consumption in 3.
PAGE 15
TELEPHONE LINE ISOLATION BARRIER RECEIVE 2-WIRE ISDN LINE PROTECTION CIRCUIT TRANSMIT LINE POLARITY HCPL-4731 PRIMARY–SECONDARY POWER ISOLATION BARRIER LINE PRESENCE TELEPHONE LINE INTERFACE CIRCUIT SECONDARY/ EMERGENCY POWER HCPL-4701 EMERGENCY POWER VAC PRIMARY P0WER SUPPLY SWITCHED– MODE SECONDARY POWER VCC VCC – RETURN POWER SUPPLY NOTE: THE CIRCUITS SHOWN IN THIS FIGURE REPRESENT POSSIBLE, FUNCTIONAL APPLICATION OF THE HCPL-47XX OPTOCOUPLER TO AN ISDN LINE INTERFACE.
PAGE 16
Data Communication and Input/Output Interfaces In data communication, the HCPL-47XX can be used as a line receiver on a RS-232-C line or this optocoupler can be part of a proprietary data link with low input current, multi-drop stations along the data path. Also, this low-power optocoupler can be used within equipment that monitors the presence of highvoltage.
PAGE 17
VCC + 4.7 µF – VF V R1 = CC IF 0.1 µF R1 FOR VCC = 5 Vdc, IF = 40 µA R1 = 91 kΩ (TYPICAL) R1 = 75 kΩ (WORST CASE) R1 = * VOH – VF IF FOR VCC = 5 Vdc, IF = 40 µA R1 = 36 kΩ (TYPICAL) R1 = 30 kΩ (WORST CASE) * R1 HCPL-47XX ACTIVE OUTPUT OR OPEN COLLECTOR * USE ANY SIGNAL DIODE. * USE ANY STANDARD SCHOTTKY DIODE. + 4.7 µF 0.1 µF R1 R1 = VCC – VF – VOL IF R2 = 0.8 V IOH MAX Figure 14. Recommended Alternative LED Driver Circuit for HCPL-4701/-4731 .