Datasheet

ManualsBrandsBROADCOM ManualsOptoelectronics & DisplaysTransistor-Output-Optocoupler DIP 8 Type (misc.) 2 MBd, 1-channel

Description

These dual channel optocouplers contain a pair of light

emitting diodes and integrated photo-detectors with

electrical insulation between input and output. Separate

connection for the photodiode bias and output transis-

tor collectors increase the speed up to a hundred times

that of a conventional phototransistor coupler by

reducing the base-collector capacitance.

These dual channel optocouplers are available in an 8

Pin DIP and in an industry standard SO-8 package. The

following is a cross reference table listing the 8 Pin DIP

part number and the electrically equivalent SO-8 part

number.

SO-8

8 Pin DIP Package

HCPL-2530 HCPL-0530

HCPL-2531 HCPL-0531

HCPL-4534 HCPL-0534

HCPL-2530, HCPL-2531, HCPL-4534

HCPL-0530, HCPL-0531, HCPL-0534

Features

• 15 kV/µs minimum common mode transient immunity at

= 1500 V (HCPL-4534/0534)

• TTL compatible

• Available in 8 pin DIP, SO-8, and 8 pin DIP – gull wing

surface mount (option 020) packages

• High density packaging

• 3 MHz bandwidth

• Open collector outputs

• Guaranteed performance from 0°C to 70°C

• Safety approval

UL Recognized – 3750 V rms for 1 minute (5000 V rms for 1

minute for Option 020) per UL1577

CSA Approved

IEC/EN/DIN EN 60747-5-2

–V

IORM

= 630 Vpeak for HCPL-2530/2531/4534 0ption 060

–V

IORM

= 560 Vpeak for HCPL-0530/0531/0534 0ption 060

• Single channel version available (4502/3, 0452/3)

• MIL-PRF-38534 hermetic version available

(55XX/65XX/4N55)

Applications

• Line receivers – high common mode transient immunity

(>1000 V/µs) and low input-output capacitance (0.6 pF)

• High speed logic ground isolation – TTL/TTL, TTL/LTTL,

TTL/CMOS, TTL/LSTTL

• Replace pulse transformers – save board space and

weight

• Analog signal ground isolation – integrated photon

detector provides improved linearity over phototransistor

type

• Polarity sensing

• Isolated analog amplifier – dual channel packaging

enhances thermal tracking

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this

component to prevent damage and/or degradation which may be induced by ESD.

Functional Diagram

A 0.1 µF bypass capacitor between

pins 5 and 8 is recommended.

ANODE

CATHODE

ANODE

GND

TRUTH TABLE

(POSITIVE LOGIC)

LED

OFF

LOW

HIGH

Dual Channel, High Speed Optocouplers

Data Sheet

Summary of content (14 pages)

PAGE 1
HCPL-2530, HCPL-2531, HCPL-4534 HCPL-0530, HCPL-0531, HCPL-0534 Dual Channel, High Speed Optocouplers Data Sheet Description These dual channel optocouplers contain a pair of light emitting diodes and integrated photo-detectors with electrical insulation between input and output. Separate connection for the photodiode bias and output transistor collectors increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance.
PAGE 2
The SO-8 does not require “through holes” in a PCB. This package occupies approximately one-third the footprint area of the standard dual-in-line package. The lead profile is designed to be compatible with standard surface mount processes. The HCPL-2530/0530 is for use in TTL/CMOS, TTL/LSTTL or wide bandwidth analog applications. Current transfer ratio (CTR) for the HCPL-2530/0530 is 7% minimum at IF = 16 mA. a 5.6 kΩ pull-up resistor. CTR of the HCPL-2531/0531 is 19% minimum at IF = 16 mA.
PAGE 3
Ordering Information HCPL-2530, HCPL-2531, HCPL-4534, HCPL-0530, HCPL-0531 and HCPL-0534 are UL Recognized with 3750 Vrms for 1 minute per UL1577 and are approved under CSA Component Acceptance Notice #5, File CA 88324.
PAGE 4
Schematic 1 ICC I F1 + 8 VF1 I O1 – 7 VCC VO1 2 3 I F2 – I O2 6 VF2 VO2 + 4 GND 5 HCPL-4534/0534 SHIELD USE OF A 0.1 µF BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS RECOMMENDED. Package Outline Drawings 8-Pin DIP Package (HCPL-2530/2531/4534) 7.62 ± 0.25 (0.300 ± 0.010) 9.65 ± 0.25 (0.380 ± 0.010) TYPE NUMBER 8 7 6 5 OPTION CODE* 6.35 ± 0.25 (0.250 ± 0.010) DATE CODE A XXXXZ YYWW RU 1 1.19 (0.047) MAX. 2 3 4 UL RECOGNITION 1.78 (0.070) MAX. 5° TYP. 3.56 ± 0.13 (0.
PAGE 5
Package Outline Drawings, continued 8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2530/2531/4534) LAND PATTERN RECOMMENDATION 9.65 ± 0.25 (0.380 ± 0.010) 6 7 8 1.016 (0.040) 5 6.350 ± 0.25 (0.250 ± 0.010) 1 3 2 10.9 (0.430) 4 2.0 (0.080) 1.27 (0.050) 9.65 ± 0.25 (0.380 ± 0.010) 1.780 (0.070) MAX. 1.19 (0.047) MAX. 7.62 ± 0.25 (0.300 ± 0.010) + 0.076 0.254 - 0.051 + 0.003) (0.010 - 0.002) 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) 0.635 ± 0.25 (0.025 ± 0.
PAGE 6
Solder Reflow Thermal Profile 300 TEMPERATURE (°C) PREHEATING RATE 3°C + 1°C/–0.5°C/SEC. REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. PEAK TEMP. 245°C PEAK TEMP. 240°C PEAK TEMP. 230°C 200 2.5°C ± 0.5°C/SEC. SOLDERING TIME 200°C 30 SEC. 160°C 150°C 140°C 30 SEC. 3°C + 1°C/–0.5°C 100 PREHEATING TIME 150°C, 90 + 30 SEC. 50 SEC. TIGHT TYPICAL LOOSE ROOM TEMPERATURE 0 0 50 100 150 200 250 TIME (SECONDS) Note: Non-halide flux should be used.
PAGE 7
Insulation and Safety Related Specifications Parameter Minimum External Air Gap (External Clearance) Minimum External Tracking (External Creepage) Minimum Internal Plastic Gap (Internal Clearance) Minimum Internal Tracking (Internal Creepage) Tracking Resistance (Comparative Tracking Index) Isolation Group Symbol L(101) Value 7.1 8-Pin DIP (300 Mil) SO-8 Value Units 4.9 mm L(102) 7.4 4.8 mm Measured from input terminals to output terminals, shortest distance path along body. 0.08 0.
PAGE 8
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics (Option 060) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤ 150 V rms for rated mains voltage ≤ 300 V rms for rated mains voltage ≤ 600 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working Insulation Voltage Input to Output Test Voltage, Method b* VIORM x 1.
PAGE 9
Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature Average Forward Input Current (each channel) Peak Forward Input Current (each channel) (50% duty cycle, 1 ms pulse width) Peak Transient Input Current (each channel) (≤ 1 µs pulse width, 300 pps) Reverse LED Input Voltage (each channel) Input Power Dissipation (each channel) Average Output Current (each channel) Peak Output Current Supply Voltage (Pin 8-5) Output Voltage (Pins 7-5, 6-5) Output Power Dissipation (each channel) Lead
PAGE 10
Electrical Specifications (DC) Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified. See note 9. Parameter Sym. Device Min. Current Transfer Ratio CTR HCPL-2530/ 0530 7 VOL 19 18 50 % TA = 25°C 24 50 % TA = 25°C 0.1 0.5 V HCPL-2530/ 0530 TA = 25°C 0.5 0.1 0.5 V TA = 25°C 0.5 IOH 0.003 0.5 IO = 1.1 mA 1, 2 4 1, 2 IF = 16 mA, VCC = 4.5 V 1 1 6 1 3 1 IO = 3.0 mA IO = 2.4 mA µA TA = 25°C VCC = VO = 5.
PAGE 11
Switching Specifications (AC) Over recommended temperature (TA = 0°C to 70°C), VCC = 5 V, IF = 16 mA unless otherwise specified. Parameter Propagation Delay Time to Logic Low at Output Propagation Delay Time High to Logic at Output Common Mode Transient Immunity at Logic High Level Output Common Mode Transient Immunity at Logic Low Level Output Bandwidth Sym.
PAGE 12
30 mA 25 mA 5 20 mA 15 mA 10 mA IF = 5 mA 0 0 20 10 8. 9. 1.5 1000 HCPL-2530/0530 HCPL-2531/0531/4534/0534 1.0 0.5 NORMALIZED I F = 16 mA VO = 0.5 V VCC = 5 V TA = 25°C 0.1 0 2000 1.1 1.0 0.9 NORMALIZED IF = 16 mA VO = 0.5 V VCC = 5 V TA = 25°C HCPL-2530/0530 HCPL-2531/0531/4534/0534 0.6 -60 -40 -20 0 20 40 10 60 80 100 TA – TEMPERATURE – °C Figure 4. Current transfer ratio vs. temperature. 1500 1.0 0.1 0.01 t PHL 500 -20 20 60 1.2 1.3 1.5 1.4 1.6 Figure 3.
PAGE 13
0.30 NORMALIZED RESPONSE –dB ∆ IO ∆ I F – SMALL SIGNAL CURRENT TRANSFER RATIO 0 TA = 25°C, RL = 100 Ω, VCC = 5 V 0.20 0.10 TA = 25°C IF = 16 mA -5 RL = 100 Ω RL = 220 Ω RL = 470 Ω RL = 1 kΩ -10 -15 -20 -25 -30 0.01 1.0 0.1 10 f – FREQUENCY – MHz 0 0 4 8 12 16 20 24 +5 V SET I F IF – QUIESCENT INPUT CURRENT – mA 20 kΩ AC INPUT Figure 7. Small-signal current transfer ratio vs. quiescent input current. 1 8 2 7 3 6 +5 V RL 2N3053 0.1 µF 560 Ω 100 Ω VO 0.1 µF 4 5 1.
PAGE 14
For product information and a complete list of distributors, please go to our website: www.avagotech.com Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © 2007 Avago Technologies Limited. All rights reserved.