Datasheet

ManualsBrandsBROADCOM ManualsDisplaysLED component Red (L x W x H) 10.87 x 8.84 x 4.65 mm

Description

These tinted diused LED lamps are designed and opti-

mized specically for low DC current operation. Luminous

intensity and forward voltage are tested at 2 mA to assure

consistent brightness at TTL output current levels.

Applications

• Low power DC circuits

• Telecommunications indicators

• Portable equipment

• Keyboard indicators

Package Dimensions

HLMP-4700, HLMP-4719, HLMP-4740

HLMP-1700, HLMP-1719, HLMP-1790

T-1

(5 mm), T-1 (3 mm), Low Current LED Lamps

Data Sheet

Features

• Low power

• High eciency

• CMOS-MOS compatible

• TTL compatible

• Wide viewing angle

• Choice of package styles

• Choice of colors

A - HLMP-4700, -4719, -4740

B - HLMP-1700, -1719, -1790

Notes:

1. All dimensions are in mm (inches).

2. An epoxy meniscus may extend about 1 mm (0.040") down the leads.

3. For PCB hole recommendations, see the Precautions section.

25.40 (1.00)

MIN.

2.54 (0.100) NOM.

0.55 (0.022)

0.40 (0.016)

6.10 (0.240)

5.59 (0.220)

1.27(0.050)

NOM.

0.89 (0.035)

0.64 (0.025)

5.08 (0.200)

4.57 (0.180)

9.19 (0.362)

8.43 (0.332)

SQUARE TYP.

CATHODE

0.65 (0.026) MAX.

24.1 (.95) MIN.

4.70 (.185)

4.19 (.165)

3.43 (.135)

2.92 (.115)

1.52 (.060)

1.02 (.040)

2.79 (.110)

2.29 (.090)

1.14 (.045)

0.51 (.020)

(0.022) 0.55

(0.016) 0.40

SQUARE TYP.

∅

3.17 (.125)

2.67 (.105)

6.35 (.250)

5.58 (.220)

CATHODE

Summary of content (10 pages)

PAGE 1
HLMP-4700, HLMP-4719, HLMP-4740 HLMP-1700, HLMP-1719, HLMP-1790 T-13/4 (5 mm), T-1 (3 mm), Low Current LED Lamps Data Sheet Description Features These tinted diffused LED lamps are designed and optimized specifically for low DC current operation. Luminous intensity and forward voltage are tested at 2 mA to assure consistent brightness at TTL output current levels.
PAGE 2
Selection Guide Package Description Color Device HLMP- T-1 3/4 Tinted Diffused Red Yellow Green T-1 Tinted Diffused Red Yellow Green Luminous Intensity Iv (mcd) at 2 mA Min. Typ. Max. 2q1/2 Package Outline 4700 1.5 2.3 – 50 A 4700-C00xx 1.5 2.3 – 4700-CD0FH 1.5 2.3 4.2 4719 0.9 2.1 – 4719-A00xx 0.9 2.1 – 4740 1.0 2.3 – 4740-A00xx 1.0 2.3 – 4740-AB000 1.0 2.3 3.2 1700 0.8 2.1 – 50 B 1700-B00xx 0.8 2.1 – 1719 0.9 2.1 – 1719-A00xx 0.9 2.
PAGE 3
Part Numbering System HLMP – X 7 XX - X X X XX Mechanical Option 00: Bulk 01: Tape & Reel, Crimped Leads 02, BH: Tape & Reel, Straight Leads A1, B1: Right Angle Housing, Uneven Leads A2, B2: Right Angle Housing, Even Leads FH: 2 Iv bins select with Inventory Control Color Bin Options 0: Full color bin distribution B: Color bins 2 & 3 only Maximum Iv Bin Options 0: Open (No. max.
PAGE 4
Electrical/Optical Characteristics at TA = 25°C Symbol Description T-13/4 T-1 VF Forward Voltage 4700 VR Reverse Breakdown Voltage ld Dl1/2 tS C RqJ-PIN lPEAK hV Min. Typ. Max. Units Test Conditions 1700 1.7 2.0 V 2 mA 4719 1719 1.8 2.5 4740 1790 1.9 2.2 4700 1700 5.0 V IR = 50 μA nm Note 1 4719 1719 5.0 4740 1790 5.
PAGE 5
Absolute Maximum Ratings Parameter Maximum Rating Units 14 17.5 15.4 mW DC and Peak Forward Current 7 mA Transient Forward Current (10 μs Pulse)[1] 500 mA Reverse Voltage (IR = 50 μA) 5.0 V -40 to 100 -20 to 100 °C °C -40 to +100 °C Power Dissipation (Derate linearly from 92°C at 1.0 mA/°C) Red Yellow Green Operating Temperature Range Red/Yellow Green Storage Temperature Range Notes: 1.
PAGE 6
10° 0° 1.0 20° 0° 10° 1.0 30° 40° 40° 0.6 60° 0.4 70° RELATIVE INTENSITY 0.8 50° 0.2 80° 0.0 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° 90° 0.8 50° 0.6 60° 0.4 70° RELATIVE INTENSITY 20° 30° 0.2 80° 0.0 10° 20° 30° 40° 50° 60° 70° 80° 90° 100° 90° Figure 4. Relative luminous intensity vs. angular displacement for T-13/4 lamp. Figure 5. Relative llluminous intensity vs. angular displacement for T-1 lamp.
PAGE 7
Intensity Bin Limits Color Categories Intensity Range (mcd) Color Bin Min. Max. Green A 1.1 B Lambda (nm) Color Category # Min. Max. 1.8 6 561.5 564.5 1.8 2.9 5 564.5 567.5 C 2.9 4.7 4 567.5 570.5 D 4.7 7.6 3 570.5 573.5 E 7.6 12.0 2 573.5 576.5 F 12.0 19.1 1 582.0 584.5 G 19.1 30.7 3 584.5 587.0 H 30.7 49.1 2 587.0 589.5 I 49.1 78.5 4 589.5 592.0 J 78.5 125.7 5 592.0 593.0 K 125.7 201.1 L 201.1 289.0 M 289.0 417.0 N 417.
PAGE 8
Precautions: Lead Forming: • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering on PC board. • For better control, it is recommended to use proper tool to precisely form and cut the leads to applicable length rather than doing it manually. • If manual lead cutting is necessary, cut the leads after the soldering process. The solder connection forms a mechanical ground which prevents mechanical stress due to lead cutting from traveling into LED package.
PAGE 9
Example of Wave Soldering Temperature Profile for TH LED 250 Recommended solder: Sn63 (Leaded solder alloy) SAC305 (Lead free solder alloy) LAMINAR HOT AIR KNIFE TURBULENT WAVE Flux: Rosin flux Solder bath temperature: 245°C± 5°C (maximum peak temperature = 250°C) TEMPERATURE (°C) 200 Dwell time: 1.5 sec – 3.0 sec (maximum = 3sec) 150 Note: Allow for board to be sufficiently cooled to room temperature before exerting mechanical force.
PAGE 10
DeptID: Made In: Country of Origin (ii) Avago Baby Label (Only available on bulk packaging) Lamps Baby Label (1P) PART #: Part Number RoHS Compliant e3 max temp 250C (1T) LOT #: Lot Number (9D)MFG DATE: Manufacturing Date QUANTITY: Packing Quantity C/O: Country of Origin Customer P/N: CAT: Intensity Bin Supplier Code: BIN: Color Bin DATECODE: Date Code For product information and a complete list of distributors, please go to our web site: www.avagotech.