Datasheet

ManualsBrandsBROADCOM ManualsDisplaysLED component Red (L x W x H) 11.07 x 9.02 x 6.21 mm

HLMP-D150, HLMP-D155, HLMP-K150 and HLMP-K155

T-13/4 (5 mm), T-1 (3 mm), Low Current,

Double Heterojunction AlGaAs Red LED Lamps

Data Sheet

Features

• Minimum luminous intensity specied at 1 mA

• High light output at low currents

• Wide viewing angle

• Outstanding material eciency

• Low power/low forward voltage

• CMOS/MOS compatible

• TTL compatible

• Deep red color

Description

These solid state LED lamps utilize double heterojunction

(DH) AlGaAs/GaAs material technology. This LED material

has outstanding light output eciency at very low drive

currents. The color is deep red at the dominant wave-

length of 637 nanometres. These lamps are ideally suited

for use in applications where high light output is required

with minimum power output.

Applications

• Low power circuits

• Battery powered equipment

• Telecommunication indicators

Package Dimensions

Notes:

1. All dimensions are in mm (inches).

2. An epoxy meniscus may extend about 1 mm (0.040") down the leads.

3. For PCB hole recommendations, see the Precautions section.

25.40 (1.00)

MINIMUM

1.27(0.050)

NOM.

0.89 (0.035)

0.64 (0.025)

5.08 (0.200)

4.57 (0.180)

9.19 (0.362)

8.43 (0.332)

0.65 (0.026) MAX.

CATHODE

0.55 (0.022)

0.40 (0.016)

SQ. TYP.

2.54 (0.100) NOM.

6.10 (0.240)

5.59 (0.220)

6.1 (0.240)

5.6 (0.220)

23.0

(0.90)

MIN.

0.46 (0.018)

SQUARE NOMINAL

2.54 (0.100)

NOM.

CATHODE

1.27 (0.050)

NOM.

0.89 (0.035)

0.64 (0.025)

9.19 (0.362)

8.43 (0.332)

12.44 (0.490)

11.68 (0.460)

1.32 (0.052)

1.02 (0.040)

5.08 (0.200)

4.57 (0.180)

0.65 (0.026) max.

24.1(.95) min.

4.70 (.185)

4.19 (.165)

3.43 (.135)

2.92 (.115)

1.52 (.060)

1.02 (.040)

2.79 (.110)

2.29 (.090)

1.14 (.045)

0.51 (.020)

(0.022) 0.55

SQ. TYP.

(0.016) 0.40

3.17 (.125)

2.67 (.105)

6.35 (.250)

5.58 (.220)

A. B.

Summary of content (9 pages)

PAGE 1
HLMP-D150, HLMP-D155, HLMP-K150 and HLMP-K155 T-13/4 (5 mm), T-1 (3 mm), Low Current, Double Heterojunction AlGaAs Red LED Lamps Data Sheet Description Features These solid state LED lamps utilize double heterojunction (DH) AlGaAs/GaAs material technology. This LED material has outstanding light output efficiency at very low drive currents. The color is deep red at the dominant wavelength of 637 nanometres.
PAGE 2
Selection Guide Luminous Intensity Iv (mcd) at 1 mA Package Description Device HLMP- Min. Typ. Max. 2θ1/2[1] Degree T-1 3/4 Red Tinted Diffused D150 1.3 3.0 – 65 A D150-C00xx 1.3 3.0 – 65 A D155 5.4 10.0 – 24 B D155-F00xx 5.4 10.0 – 24 B K150 1.3 2.0 – 60 C K150-C00xx 1.3 2.0 – 60 C K150-CD0xx 1.3 3.0 4.2 60 C K155 2.1 3.0 – 45 C K155-D00xx 2.1 3.
PAGE 3
Absolute Maximum Ratings at TA = 25°C Parameter Value Peak Forward Current[1] 300 mA Average Forward Current 20 mA DC Current[2] 30 mA Power Dissipation 87 mW Reverse Voltage (IR = 100 μA) 5V Transient Forward Current (10 μs Pulse)[3] 500 mA LED Junction Temperature 110°C Operating Temperature Range -20 to +100°C Storage Temperature Range -40 to +100°C Notes: 1. Maximum IPEAK at f = 1 kHz, DF = 6.7%. 2. Derate linearly as shown in Figure 4. 3.
PAGE 4
Figure 1. Relative intensity vs. wavelength. Figure 2. Forward current vs. forward voltage. Figure 3. Relative luminous intensity vs. dc forward current. Figure 4. Maximum forward dc current vs. ambient temperature. Derating based on TJ Max. = 110 °C. Figure 5. Relative luminous intensity vs. angular displacement. HLMP-D150. Figure 6. Relative luminous intensity vs. angular displacement. HLMP-K150.
PAGE 5
Figure 7. Relative luminous intensity vs. angular displacement. HLMP-D155. Intensity Bin Limits Intensity Range (mcd) Color Bin Min. Max. Red C 1.5 2.4 D 2.4 3.8 E 3.8 6.1 F 6.1 9.7 G 9.7 15.5 H 15.5 24.8 I 24.8 39.6 J 39.6 63.4 K 63.4 101.5 L 101.5 162.4 M 162.4 234.6 N 234.6 340.0 O 340.0 540.0 P 540.0 850.0 Q 850.0 1200.0 R 1200.0 1700.0 S 1700.0 2400.0 T 2400.0 3400.0 U 3400.0 4900.0 V 4900.0 7100.0 W 7100.0 10200.0 X 10200.0 14800.
PAGE 6
Mechanical Option Matrix Mechanical Option Code Definition 00 Bulk Packaging, minimum increment 500 pcs/bag 01 Tape & Reel, crimped leads, minimum increment 1300 pcs for T-13/4, 1800 pcs for T-1 02 Tape & Reel, straight leads, minimum increment 1300 pcs for T-13/4, 1800 pcs for T-1 A1 T-1, Right Angle Housing, uneven leads, minimum increment 500 pcs/bag A2 T-1, Right Angle Housing, even leads, minimum increment 500 pcs/bag B1 T-13/4, Right Angle Housing, uneven leads, minimum increment 500 pcs/
PAGE 7
Precautions: Lead Forming: • The leads of an LED lamp may be preformed or cut to length prior to insertion and soldering on PC board. • For better control, it is recommended to use proper tool to precisely form and cut the leads to applicable length rather than doing it manually. • If manual lead cutting is necessary, cut the leads after the soldering process. The solder connection forms a mechanical ground which prevents mechanical stress due to lead cutting from traveling into LED package.
PAGE 8
Example of Wave Soldering Temperature Profile for TH LED 250 Recommended solder: Sn63 (Leaded solder alloy) SAC305 (Lead free solder alloy) LAMINAR HOT AIR KNIFE TURBULENT WAVE Flux: Rosin flux Solder bath temperature: 245°C± 5°C (maximum peak temperature = 250°C) TEMPERATURE (°C) 200 Dwell time: 1.5 sec – 3.0 sec (maximum = 3sec) 150 Note: Allow for board to be sufficiently cooled to room temperature before exerting mechanical force.
PAGE 9
DeptID: Made In: Country of Origin (ii) Avago Baby Label (Only available on bulk packaging) Lamps Baby Label (1P) PART #: Part Number RoHS Compliant e3 max temp 250C (1T) LOT #: Lot Number (9D)MFG DATE: Manufacturing Date QUANTITY: Packing Quantity C/O: Country of Origin Customer P/N: CAT: Intensity Bin Supplier Code: BIN: Color Bin DATECODE: Date Code For product information and a complete list of distributors, please go to our web site: www.avagotech.