BMC R708A User Manual Interface key Illustrate Power key Long press over 5 seconds to power on and long press to power off WPS Press to active the WPS Reset The Reset button is on the opposite side of the machine. If you forget Administrator password or Wireless network key, you can press the Reset key to restore factory default settings.
Red Blue Blink: Connected to2G network Solid:No Service/Device Error Solid:No Client Blink: Client is actived Blink: WPS is actived WiFi LED Blink: Turn on-0.2s Turn off-0.1s Installation Follow the diagram to install the SIM card and SD card Tips: Always switch the device off and disconnect the charger before removing the battery. 1. Remove the back cover and battery; 2. Insert the SIM card and SD card.
Your battery has been partially charged at the factory. If the device indicates a low charge, do the following: 1. Connect the charger to an outlet. 2. Connect the USB charger plug to your device’s USB port. 3. When the device indicates a full charge, disconnect the charger from the device, then from the outlet.
BMC R708A Usage R708A support 4G/3G networks. Insert the SIM card, Wi-Fi devices and the computer can access the Internet through R708A, enjoy high-speed network services.Smart phones, tablet computers, game consoles and other Wi-Fi devices can be connected with the R708A Wi-Fi connection for Internet access. Computers & laptops etc. may be connected to the R708A via USB cable for Internet Access.
Method Two: Login management page view 1.Computer, open your browser, input http://192.168.0.1 and enter. ●The default Account is admin ●The default Password is admin Enter the Account and Password, login the administration pages 2.
●The default SSID is R708A ●The default Wi-Fi Password is 87654321 ★Recommend that you start using R708A administration pages after setting a convenient landing memorizing SSID and a higher safety factor Wi-Fi passwords Install the driver and connecting the device USB Connection:Windows 7 for example 1. Keep R708A powering on,Plug the device into your computer,it will shows like the following pictures step by step.
2.
3. Check the network card is installed correctly,like the following pictures Or, Establish Wi-Fi connection:you must ensure that the computer equipped with a wireless network card.
connectivity, the wireless LAN is available. Otherwise, you need to check your wireless network card is working properly. 1. In the Wi-Fi list, select the SSID consistent with R708A Wi-Fi, click Connect 2. Enter the correct Wi-Fi password, click OK 3.
WebUI ●Home First part of the main display settings and network status information, such as IPaddress, SIM card status, type and quality of the network signal, whether it is roaming, with or without a new message, and traffic statistics,and system
uptime,and so on. ●Wizard You can quickly change the LAN configuration, set the APN , and change the SSID \ password through the wizard function.
●WAN 1.Connection Dialing Mode: Select the Auto Mode, after you turn on R708A without additional operations, the device will automatically connect to the network; select the Manual Mode, you need to manually connect to the network after opening the R708A management page. 2.APN Setting: You can customize the network configuration or manually add the new APN and set default APN.
3.4G/3G Modem There are four types of networks can be choose: Auto is 4G/3G, LTE Only is using only 4G, WCDMA Only is using only 3G. 4.
the page will prompted to enter the correct PIN code, you can use the SIM card. PIN / PUK code supplied with the SIM card provided by your carrier, please consult your carrier. 4. PLMN Public Land Mobile Network have two mode, one is automatic,the other is manual.You can search the current network manually and register. 1.LAN We can change IP address in this page. 2.
DHCP Mode: Select the server mode, the device can be done using a DHCP server; choose None, which is off the server function. Start / End IP address: Changing DHCP assigned IP and IP segments. Lease Time: Each is assigned a time to use the IP LeasedHosts: the R708A each wireless device list and USB device can view the Host name, MAC Address, IP Address, information about the Remaining Time. ●SMS When using SIM card to access network, you could also send text messages at the time.
you can setting the storage location of messages, and so on. We can operating the SMS in this page. ●Wi-Fi 1.Basic We can setting the wifi configuration in this page, like B/G/N mode, Channel, SSID,WIFI KEY and so on. 2.WPS R708A supports two kinds of WPS authentication, PBC and PIN. Default is PBC authentication.
If your WiFi Enabled ,device supports WPS (WiFi Protected Setup) and you have forgotten or do not wish to enter your password to connect to your R708A, you may use the following available procedures for quick access to WiFi. Open the WPS: WPS can be opened by two methods. The fist method is , Entering the management interface page, press the “Apply“ button , open the WPS. It will lasting 120 seconds. Like the following picture.
Or Select the SSID of the device and connect. then you can see connecting process The second method is, Select the SSID of the device and connect Press the WPS button on theR708A, activate the WPS. It will lasting 120 seconds. then you can see connecting process.
WPS PIN authentication: The connection to the R708A is achieved by inputting the relevant PIN key into the enrollee PIN text box, which you may find in the wireless network card. When you applied, It will lasting 120 seconds. The premise is that the wireless network card or the clients must support WPS PIN authentication. Like the following pictures.
3. MAC Filter Deny list Stations: If you add the computers or wireless devices MAC address into the list, it can prohibiting the computers or wireless devices connect to the R708A.The computes or wireless devices MAC address which are not in the list can able to connect to R708A. Allow list Stations: Opposite with Deny list Stations.
Showthe information of wireless devices which are connected to the R708A. ●Security 1. Firewall Firewall configuration: You can Disable or Enable the Firewall function. Also you can setting the matching packets ipv6/ipv4 rule to receive or reject.
You can add the rule in the list and click apply confirm it. 2. NAT The R708A supports NAT/IPSEC VPN Pass Through/PPTP VPN Pass Through/L2TP VPN Pass Through/Webserver WWAN Access. When some hosts inside the private network have already allocated the local IP address, that is, only the private address used in the private network, but now they want to communicate with the host on the Internet (no need to encrypt), we can use the NAT method. 3.
Receive all the data from external network interface forwarded to“DMZ IP address” Enable DMZ: If an application has trouble working from behind the router, you can expose one computer to the Internet and run the application on that computer. Note: Placing a computer in the DMZ may expose that computer to a variety of security risks. Use of this option is only recommended as a last resort.
Restore the factory settings, All the personal configuration will be deleted, all configuration pages will be restored to the factory defaults. 3.Firmware Upgrade The page allows you to upgrade the firmware. It have two mode. Remote Server: When you power on the device , if you insert the SIM card and register the internet .it can automatic check whether there is a new version, if there is a new version was detected, can be directly upgrade.
Modify the login password for administrator interface. Also you can setting the time to logout the UI automatically. 5.Date and Time You can synchronize the time with the host , you can also select the time zone 6.
You can change the UI language in this page. 5.Power saving You can change the time of sleep mode or deep sleep mode. In this page you also can Disable the Power saving function. Sleep mode: System will enter into the sleep mode, when there is no Wi-Fi client connected to this device. Deep sleep mode: System will enter into deep sleep mode, when there is no Internet access and no Wi-Fi client connected to this device. 8.
BATTERIES ACCORDING TO THE INSTRUCTIONS FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
