R800C User Manual Interface key Illustrate Power key Long press over 5 seconds to power on and long press to power off WPS Press to active the WPS Reset The Reset button is on the opposite side of the machine. If you forget Administrator password or Wireless network key, you can press the Reset key to restore factory default settings.
Green Purple Red Blue Blink: Register to 3G(not connect) Solid: Connected to3G network Blink: Register to2G(not connect) Solid: Connected to2G network Blink: No Service/Device Error Solid: No Client Blink: Client is actived Blink: WPS is active WiFi LED Blink: Turn on-0.2s Turn off-0.1s Installation Follow the diagram to install the SIM card and SD card Tips: Always switch the device off and disconnect the charger before removing the battery. 1. Remove the back cover and battery; 2.
the battery. Replace the back cover lastly. R800C Usage R800C support 4G/3G/2G networks. Insert the SIM card, Wi-Fi devices and the computer can access the Internet through R800C, enjoy high-speed network services. Smart phones, tablet computers, game consoles and other Wi-Fi devices can be connected with the R800CC Wi-Fi connection for Internet access. Computers & laptops etc. may be connected to the R800C via USB cable for Internet Access.
password, which you may find in the following ways: Method one: on the nameplate view the default SSID and Wi-Fi passwords Method Two: Login management page view
1. Computer, open your browser, input http://192.168.0.1 and enter. ●The default Account is admin ●The default Password is admin Enter the Account and Password, login administration pages 2. Enter the Wi-Fi menu, view the default SSID and Wi-Fi password. The default 2.4G SSID is R800C_2.4G.The default 5G SSID is R800C_5G.The Wi-Fi password are both 1234567890.
★Recommend that you start using R800C administration pages after setting a convenient landing memorizing SSID and a higher safety factor Wi-Fi passwords Install the driver and connecting the device USB Connection: Windows 7 for example 1. Keep R800C powering on, Plug the device into your computer, it will shows like the following pictures step by step.
2.
3. Check the network card is installed correctly, like the following pictures Or, Establish Wi-Fi connection: you must ensure that the computer equipped with a wireless network card.
connectivity, the wireless LAN is available. Otherwise, you need to check your wireless network card is working properly. (The following will be 2.4GWi-Fi as an example) 1. In the Wi-Fi list, select the SSID consistent with R800C Wi-Fi, click Connect 2. Enter the correct Wi-Fi password, click OK 3.
connection is successful 4.
Web ●Home First part of the main display settings and network status information, such as IPad dress, SIM card status, type and quality of the network signal, whether it is roaming, with or without a new message, and traffic statistics, and system uptime, and so on.
You can quickly change the LA configuration, set the APN, and change the 2.4G SSID/Password through the wizard function. ●WAN 1. Connection Dialing Mode: Select the Auto Mode, after you turn on R800C without additional operations, the device will automatically connect to the network; select the Manual Mode, you need to manually connect to the network after opening theR800C management page.
2. APN Setting: You can customize the network configuration or manually add the new APN and set defaulting. 3.
There are four types of networks can be choose: Auto is 4G/3G/2G, Leanly is using only 4G, WCDMA Only is using only 3G,GSM Only is using only 2G. 5. PIN Open your PIN, if you reboot the device, you need to login management page, and the page will prompted to enter the correct PIN code, you can use the SIM card. PIN / PUK code supplied with the SIM card provided by your carrier, please consult your carrier.
●LAN 1. LAN We can change IP address in this page. 2. DHCP DHCP Mode: Select the server mode, the device can be done using a DHCP server; choose none, which is off the server function. Start / End IP address: Changing DHCP assigned IP and IP segments.
Lease Time: Each is assigned a time to use the IP Leased Hosts: the R800C each wireless device list and USB device can view the Host name, MAC Address, IP Address, information about the Remaining Time. ●SMS When using SIM card to access network, you could also send text messages at the time. You can send, receive, reply, forward, and save test messages. You can send 10 text messages at the same time, SMS number intervals with a semicolon. Also you can setting the storage location of messages, and so on.
●Wi-Fi 1. Basic We can setting the 2.4GWi-Ficonfiguration in this page, like B/G/N mode, Channel, SSID, Wi-Fi KEY and so on. You can also control the opening and closing of 5GWi-Fi, and set up the Wi-Fi Channel .The 5GWi-Fi of R800C supports 802.11 A/N/AC Mixed protocol. We set the Channel Width to reach HT20/40/80 Mixed.
867Mbps. 2. WPS R800C supports two kinds of WPS authentication, PBC and PIN. Default is PBC authentication. (The following will be 2.
forgotten or do not wish to enter your password to connect to your R800C, you may use the following available procedures for quick access to Wi-Fi. Open the WPS: WPS can be opened by two methods. The first method is, enter the management interface page, press the “Apply “button, and open the WPS. It will lasting 120 seconds. Like the following picture.
Or Select the SSID of the device and connect. Then you can see like the following picture.
The second method, Select the SSID of the device and connect Press the WPS button on theR800C, activate the WPS. It will lasting 120 seconds. Then you can see like the following picture.
WPS PIN authentication: The connection to the R800C is achieved by inputting the relevant PIN key into the enrollee PIN text box, which you may find in the wireless network card. When you applied, it will lasting 120 seconds. The premise is that the wireless network card or the clients must support WPS PIN authentication. Like the following pictures.
3. MAC Filter Deny list Stations: If you add the computers or wireless devices MAC address into the list, it can prohibiting the computers or wireless devices connect to the R800C.The computes or wireless devices MAC address which are not in the list can able to connect to R800C. Allow list Stations: Opposite with Deny list Stations.
Show the information of wireless devices which are connected to the 2.4GWi-Fi and 5GWi-Fi. ●Security 1. Firewall Firewall configuration: You can Disable or Enable the Firewall function. Also you can setting the matching packets rule to receive or reject.
You can add the rule in the list. ●System 1. About R800C displays some basic information, such as device name, firmware version, IMEI, baseband version.
2. Configuration Restore the factory settings, all the personal configuration will be deleted, all configuration pages will be restored to the factory defaults. 3.
Select the file to update the software 4. Password Modify the login password for administrator interface. Also you can setting the time to logout the automatically. 5.
You can synchronize the time with the host, you can also select the time zone 6. Language You can change the UI language in this page. 7.
You can change the time of sleep mode or deep sleep mode. In this page you also can disable the Power saving function. Sleep mode: System will enter into the sleep mode, when there is no Wi-Fi client connected to this device. Deep sleep mode: System will enter into deep sleep mode, when there is no Internet access and no Wi-Fi client connected to this device. 8.
Safety Warning Caution:RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
