RDF2 READ AND SAVE THESE INSTRUCTIONS Installer: leave this guide with homeowner. Register your product online at: www.broan.com/register or www.nutone.com/register.
RDF2 Installation Guide Page 2 Usage Tools Required For use with 1, 2, or 3-Hour-Rated Floor-Ceiling and RoofCeiling Designs. - or - - or - Flat Ceiling / Horizontal Mount Only. For use with the following ventilation fan models: Broan LP50100DC Preparation The following steps are best performed on a work surface before fan installation. Protect counter tops by placing corrugated sheet under the fan.
RDF2 Installation Guide Page 3 Concrete Slab or T-Bar Construction - UL / cUL Installation 5A Install Fan/Damper Assembly Mount fan/damper assembly to the deck or ceiling structure above or adjacent to the assembly. If the assembly is hung from the structure above, a minimum 12 steel wire gauge (3mm) hanger wire must be used. The unit must be hung with four wires, one on each side.
RDF2 Installation Guide Page 4 6 Finish Fan Installation SLOT (2) Follow instructions packed with fan to connect ductwork and electrical wiring to fan. GRILLE SPRING (2) Finish ceiling around damper housing. 7 Install Grille REMOVE THE MASK BEFORE INSTALLING GRILLE OR OPERATING FAN. GRILLE Attach the grille over the inlet face of the damper by inserting the grille springs into the slots in the sides of the damper, then push grille against ceiling.
RDF2 LIRE CES DIRECTIVES ET LES CONSERVER Installateur : veuillez laisser ce guide au propriétaire. Enregistrez votre produit en ligne à : www.broan.com/register ou www.nutone.com/register.
Guide d’installation RDF2 Page 6 Utilisation Outils requis À utiliser dans les planchers/plafonds et toits/plafonds classés résistants au feu 1, 2 ou 3 heures. - ou - - ou - Plafond plat / montage horizontal seulement. À utiliser avec les modèles de ventilateurs d’aération suivants : Broan LP50100DC Préparation Il est préférable d’effectuer les étapes suivantes sur une surface de travail avant l’installation du ventilateur.
Guide d’installation RDF2 Page 7 Bâtiment à dalle de béton ou à profilés en « T » - Installation UL / cUL Installer l’ensemble de clapet / A ventilateur 3 Fixer l’ensemble de ventilateur / clapet à la charpente de l’étage ou du plafond par le haut ou par les côtés. FIL DE SUSPENSION (4) Si l’ensemble est suspendu à la structure du plafond, utiliser du fil d’acier à suspension de calibre 12 au minimum (3 mm). L’appareil doit être suspendu par quatre fils, un de chaque côté.
Guide d’installation RDF2 Page 8 4 Terminer l’installation du ventilateur FENTE (2) Suivre les instructions accompagnant le ventilateur pour raccorder les conduits et le câblage électrique au ventilateur. RESSORT DE LA GRILLE (2) Finir le plafond autour du boîtier du clapet. 5 Installer la grille GRILLE RETIRER LE MASQUE AVANT D’INSTALLER LA GRILLE OU DE FAIRE FONCTIONNER LE VENTILATEUR.
RDF2 LEA Y CONSERVE ESTAS INSTRUCCIONES Aviso al instalador: Deje esta guía con el dueño de la casa. Registre su producto en el sitio web: www.broan.com/register o www.nutone.com/register.
Guía de instalación de RDF2 Página 10 Uso Herramientas necesarias Para usarse en los diseños de piso a cielo raso y techo a cielo raso con clasificación de 1, 2 o 3 horas. -o- -o- Solo montaje horizontal / en cielo raso plano. Para usarse con los siguientes modelos de ventilador: Broan LP50100DC Preparación Los siguientes pasos se realizan mejor sobre una superficie de trabajo antes de instalar el ventilador. Proteja las cubiertas colocando una hoja corrugada debajo del ventilador.
Guía de instalación de RDF2 Página 11 Construcción de loseta de concreto o barra T - Instalación según UL / cUL nstale el conjunto del 5A Iventilador/regulador Monte el conjunto de ventilador/regulador en la plataforma o estructura del cielo raso que se encuentra arriba o adyacente al conjunto. ALAMBRE DE SUSPENSIÓN (4) Si el conjunto se cuelga de la estructura superior, debe usar un alambre de suspensión de acero con un calibre 12 (3 mm) como mínimo.
Guía de instalación de RDF2 Página 12 6 Termine la instalación del ventilador RANURA (2) Siga las instrucciones incluidas con el ventilador para conectar los conductos y el cableado eléctrico al ventilador. RESORTE DE LA REJILLA (2) Termine el cielo raso alrededor de la cubierta del regulador. 7 Instale la rejilla REJILLA QUITE LA CUBIERTA ANTES DE INSTALAR LA REJILLA O DE ACTIVAR EL VENTILADOR.