READ AND SAVE THESE INSTRUCTIONS Installer: leave this guide with homeowner. For Warranty Statement, Service Parts, Technical Support, or to Register your product, please visit our website or call: In the United States - Broan.com 800-558-1711or NuTone.com 888-336-6151. In Canada - Broan.ca or NuTone.
RDFUWT – Installation Guide Page 2 Usage For use with 1, 2, or 3-Hour-Rated Floor-Ceiling and Roof-Ceiling Designs. UL/ cUL Listed for use in the following Floor Ceiling and Roof Ceiling Assemblies: L521, L528, L546, L558, L562, L574, L576, L581, L583, L585, P522, P533, P538, P545, and P547 when installed per the following instructions: Flat Ceiling / Horizontal Mount Only.
RDFUWT – Installation Guide Page 3 C 3. Reinstall blower into fan housing. Install (2) #8 x ½” HEX HEAD SHEET METAL SCREWS (C) supplied in fan parts bag. 4. Slide (4) MOUNTING BRACKETS (D) into slots on four sides of RADIATION DAMPER EXTENSION FRAME (E). Make sure they snap into place and are securely engaged after assembly. 5. Center the radiation damper over the fan housing. Make sure NOTCH (F) is correctly positioned relative to the DUCT CONNECTOR OPENING (G). 6.
RDFUWT – Installation Guide Page 4 L T P INSERT TAB INTO SLOT IN HOUSING O ! snap Step 13: XB, ZB, XN, ZN Models ONLY TOP AND BOTTOM FLANGES REMAIN OUTSIDE OF HOUSING SCREW FROM PARTS BAG 13. Slide MOUNTING FRAME (O) onto fan housing. Pull frame up around housing until it snaps into place. Secure mounting frame to fan housing with (2) #8 X 3/8” FLAT HEAD SHEET METAL SCREWS (P) supplied in the fan parts bag. 15.
RDFUWT – Installation Guide Page 5 Prepare Ceiling & Install Fan in Ceiling This radiation Damper and Fan Combination is UL/ cUL Listed for use in the following Floor Ceiling and Roof Ceiling Assemblies: L521, L528, L546, L558, L562, L574, L576, L581, L583, L585, P522, P533, P538, P545, and P547. U 16. Install additional 2 X 4 VERTICAL BLOCKS (U) as shown. 17. Make sure lower edge of radiation damper is flush with INTERIOR SIDE OF FINISHED CEILING. 18.
RDFUWT – Installation Guide Page 6 Install Grille I 1 Step 26: Humidity-Sensing Fans and Motion Sensing Fans ONLY. 26. Connect SENSOR JUMPER WIRE (I) into the sensors connector located on the grille. 2 Y 27. Squeeze 2 GRILLE SPRINGS (Y) and slide into tabs on the radiation damper frame. Push GRILLE (Z) until it’s tight against ceiling surface. K Z If additional clearance is required between ceiling and grille, replace grille springs with longer ones (provided in parts bag).
LIRE ET CONSERVER CES INSTRUCTIONS Installateur : Laisser ce manuel au propriétaire. Pour consulter l’énoncé de garantie, commander des pièces de rechange, communiquer avec le soutien technique ou enregistrer le produit, visiter le site Web ou téléphoner. Aux États-Unis : Broan.com, 1 800 558 1711 ou NuTone.com, 1 888 336 6151. Au Canada : Broan.ca ou NuTone.
RDFUWT – Guide d’installation Page 8 Compatibilité Pour assemblages plafond/plancher ou toiture/plafond présentant une résistance au feu de 1, 2 ou 3 heures. Homologation UL/cUL pour utilisation avec les assemblages plafond/plancher et toiture/plafond L521, L528, L546, L558, L562, L574, L576, L581, L583, L585, P522, P533, P538, P545 et P547 lorsqu’installé conformément aux instructions. Fixation à plat à l’horizontale et au plafond.
RDFUWT – Guide d’installation Page 9 C 3. Réinstaller le ventilateur dans le boîtier et le fixer avec 2 VIS À TÔLE À TÊTE HEXAGONALE No 8 DE ½ po (C) provenant du sac de pièces du ventilateur. 4. Glisser les 4 LANGUETTES DE FIXATION (D) dans les fentes de chaque côté du CHÂSSIS D’EXTENSION DU REGISTRE COUPE-FEU (E) jusqu’à ce qu’elles se verrouillent en place; vérifier qu’elles sont bien fixées. 5. Aligner le châssis du registre coupe-feu et le boîtier du ventilateur.
RDFUWT – Guide d’installation Page 10 L T P INSÉRER LA LANGUETTE DANS LA FENTE DU BOÎTIER O ! snliacp! C LES SAILLIES SUPÉRIEURE ET INFÉRIEURE RESTENT À L’EXTÉRIEUR DU BOÎTIER VIS DU SAC DE PIÈCES DU VENTILATEUR Étape 13 Modèles XB, ZB, XN et ZN SEULEMENT. 13. Glisser le CHÂSSIS DE MONTAGE (O) sur le boîtier du ventilateur et le remonter jusqu’à ce qu’il se verrouille en place.
RDFUWT – Guide d’installation Page 11 Préparer le plafond et y installer le ventilateur Cet ensemble de registre coupe-feu et de ventilateur est homologué UL/cUL pour utilisation avec les assemblages plafond/plancher ou toiture/plafond suivants : L521, L528, L546, L558, L562, L574, L576, L581, L583, L585, P522, P533, P538, P545 et P547. U 16. Installer des 2 X 4 VERTICAUX (U), comme sur l’image. 17. Aligner le bas du registre coupe-feu et la SURFACE INTÉRIEURE DU PLAFOND FINI. 18.
RDFUWT – Guide d’installation Page 12 Installer la grille I 1 Étape 26 Ventilateurs avec détecteur de mouvement ou d’humidité SEULEMENT. 2 26. Brancher le RACCORDEMENT DE DÉTECTEUR (I) sur le bon connecteur de la grille. Y K Z Étape 25 Ventilateurs avec éclairage SEULEMENT. 27. Pincer les 2 RESSORTS DE LA GRILLE (Y) et insérer leurs embouts dans les fentes du châssis du registre coupe-feu. Pousser la GRILLE (Z) jusqu’à ce qu’elle soit bien appuyée au plafond.
LEA Y CONSERVE ESTAS INSTRUCCIONES Instalador: Deje esta guía con el dueño de la casa. Si desea consultar la declaración de garantía, repuestos de servicio, apoyo técnico o para registrar su producto, visite nuestro sitio web o llame: En Estados Unidos: - Broan.com 800-558-171 or NuTone.com 888-336-6151. En Canadá - Broan.ca or NuTone.
Guía de instalación del RDFUWT Página 14 Uso Para usarse en los diseños de piso a cielo raso y techo a cielo raso con clasificación de 1, 2 o 3 horas. Tiene certificación de UL/ cUL para usarse en los siguientes conjuntos de cielo raso a piso y cielo raso a techo: L521, L528, L546, L558, L562, L574, L576, L581, L583, L585, P522, P533, P538, P545 y P547 al instalarlo según las siguientes instrucciones: Solamente montaje horizontal / en cielo raso plano.
Guía de instalación del RDFUWT Página 15 3. Reinstale el soplador en la cubierta del ventilador. Instale dos (2) TORNILLOS DE CHAPA METÁLICA DE CABEZA HEXAGONAL #8 x ½ pulg. (C) que se suministran en la bolsa de piezas del ventilador. C 4. Deslice cuatro (4) SOPORTES DE MONTAJE (D) en las ranuras en cuatro lados del MARCO DE EXTENSIÓN DEL REGULADOR DE RADIACIÓN (E). Después del montaje, asegúrese de que encajen a presión en su lugar y se enganchen de forma segura. 5.
Guía de instalación del RDFUWT Página 16 L T P INTRODUZCA LA PESTAÑA EN LA RANURA DE LA CUBIERTA O LAS BRIDAS SUPERIOR E INFERIOR PERMANECEN FUERA DE LA CUBIERTA cilc! TORNILLO DE LA BOLSA DE PIEZAS Paso 13: SOLAMENTE modelos XB, ZB, XN, ZN 13. Deslice el MARCO DE MONTAJE (O) en la cubierta del ventilador. Suba el marco alrededor de la cubierta hasta que quede sujetado a presión.
Guía de instalación del RDFUWT Página 17 Prepare el cielo raso e instale allí el ventilador La combinación de regulador de radiación y ventilador tiene certificación de UL/cUL para usarse en los siguientes conjuntos de cielo raso a piso y cielo raso a techo: L521, L528, L546, L558, L562, L574, L576, L581, L583, L585, P522, P533, P538, P545 y P547. U 16. Instale BLOQUES VERTICALES 2x4 adicionales (U), como se muestra. 17.
Guía de instalación del RDFUWT Página 18 Instale la rejilla I 1 Paso 26: SOLAMENTE ventiladores con sensor de humedad y ventiladores con sensor de movimiento 2 26. Conecte EL CABLE DE PUENTE DEL SENSOR (I) en el conector del sensor ubicado en la rejilla. Y 27. Comprima 2 RESORTES DE LA REJILLA (Y) y deslícelos dentro de las lengüetas del marco del regulador de radiación. Empuje la REJILLA (Z) hasta que esté firme contra la superficie del cielo raso.
99045952F