Instructions / Assembly

ManualsBrandsBroan ManualsThermostat114

Page 1

MODEL 114

KICKSPACE HEATER

Factory Wired 240/208 V.A.C.

READ AND SAVE THESE INSTRUCTIONS

VOLTS WATTS AMPS BTU/HR

240 1500 6.3 5120

208 1125 5.4 3840

120* 1500 12.5 5120

120* 750 6.3 2560

PLANNING

This heater is designed for installation in an enclosed space such

as under a counter or kickspace to provide warm, gentle heat at

the floor level. Reread Safety Notes 3 through 8 for guidelines in

planning the installation.

The Model 114 is factory wired for 240/208 V.A.C. operation. It offers

a choice of heat outputs and can be internally connected for multiple

wattages at different voltages shown in the table below.

All ratings are 1‑Phase, 60 Hertz.

*See “FIELD CONVERSION TO 120 V.A.C.” section.

IMPORTANT INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE

INSTALLING OR USING THIS HEATER.

To reduce the risk of fire, electric shock, or injury to persons,

observe the following:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire‑rated construction codes and

standards.

4. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

5. This heater is hot when in use. To avoid burns, do not let bare

skin touch hot surfaces. Keep combustible materials, such as

furniture, pillows, bedding, papers, clothes, etc. and curtains at

least 3 feet (0.9 m) from the front of the heater.

6. Extreme caution is necessary when any heater is used by

or near children or invalids and whenever the heater is left

operating and unattended.

7. Do not operate any heater after it malfunctions. Disconnect

power at service panel and have heater inspected by a

reputable electrician before reusing.

8. Do not use outdoors.

9. To disconnect heater, turn controls to off, and turn off power

to heater circuit at main disconnect panel (or operate internal

disconnect switch, if provided).

10. Do not insert or allow foreign objects to enter any ventilation or

exhaust opening, as this may cause an electric shock or fire, or

damage the heater.

11. To prevent a possible fire, do not block air intakes or exhaust in

any manner.

12. A heater has hot and arcing or sparking parts inside. Do not

use it in areas where gasoline, paint, or flammable vapors or

liquids are used or stored.

13. Use this heater only as described in this manual. Any other use

not recommended by the manufacturer may cause fire, electric

shock, or injury to persons.

14. To avoid electrical shock: Do not install unit in a tub or shower

enclosure or any location where it may come in contact with

water. Never place a switch where it can be reached from a tub

or shower.

15. Do not connect heater to dimmer switch or speed control.

16. Do not install heater upside down or sideways. Heater must be

located in the horizontal position.

17. Do not recess louvered face of the heater more than three inches

from the vertical face of any overhang (cabinet).

18. Provide this heater with a separate electrical circuit following

directions under “Wiring” section.

19. This product is equipped with a thermostat which may start it

automatically. Turn off power at service entrance before cleaning

or servicing.

20. This heater includes a visual alarm to warn that parts are getting

excessively hot. If the alarm lights are activated, immediately

turn the heater off and inspect for any objects on or adjacent

to the heater that may cause high temperatures.

21. This product must be grounded.

SAVE THESE INSTRUCTIONS

Cutout dimension: 18‑3/8” x 3‑5/8”

Summary of content (12 pages)

PAGE 1
MODEL 114 Page 1 KICKSPACE HEATER Factory Wired 240/208 V.A.C. READ AND SAVE THESE INSTRUCTIONS IMPORTANT INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE INSTALLING OR USING THIS HEATER. To reduce the risk of fire, electric shock, or injury to persons, observe the following: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2.
PAGE 2
MODEL 114 INSTALLATION WARNING: To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater. CAUTION: High temperature, risk of fire, keep electrical cords, drapery, furnishings, and other combustibles at least 3 feet (0.9 m) from the front of the heater and away from the side and rear. Page 2 THERMOSTAT INSTALLATION NOTE: The thermostat control circuit must be wired prior to the wiring of the heater unit.
PAGE 3
MODEL 114 Page 3 3. Install thermostat from back side of front panel and fasten in place, from front, with two screws and washers provided (see illustrations). 4. Attach temperature control knob by gently pushing it on to the thermostat shaft. Flats on shaft and knob must line up for proper installation (do not force control knob onto shaft). 5. Remove black wire from thermal fuse and attach it to thermostat terminal marked “4”. 6.
PAGE 4
MODEL 114 Page 4 OPERATION Before using heater, make sure heater has been properly installed according to installation steps beginning with the “PLANNING” section on page 1. 1. Turn thermostat counterclockwise to its lowest setting. 2. Turn on power to circuit at service entrance. 3. Turn thermostat clockwise. The heating element and fan should come on. Set thermostat to desired temperature level. During proper operation, the heater will cycle on and off periodically. If heater does not come on: 1.
PAGE 5
MODEL 114 Page 5 MAINTENANCE The following maintenance and cleaning tasks can be performed by the user. All other servicing must be performed by an authorized technician If you have any questions, please consult with our cus‑ tomer service department at: 800-558-1711. LUBRICATION The heater is permanently lubricated and never needs oiling or disassembly. CLEANING Clean heater once a month as follows: 1. Turn off power at service panel. 2. Make sure heating element is cool. 3.
PAGE 6
MODEL 114 SERVICE PARTS KEY PART NO.
PAGE 7
MODELO 114 CALEFACTOR PARA ESPACIOS BAJO GABINETES Página 7 Cableado de fábrica: 240/208 VCA LEA Y CONSERVE ESTAS INSTRUCCIONES INSTRUCCIONES IMPORTANTES LEA TODAS LAS INSTRUCCIONES ANTES DE INSTALAR O USAR ESTE CALENTADOR. Para reducir el riesgo de incendios, descargas eléctricas o lesiones personales, observe las siguientes precauciones: 1. Use la unidad solo de la manera indicada por el fabricante.
PAGE 8
MODELO 114 Página 8 INSTALACIÓN 1. Marque el sitio de montaje previsto en la placa de base o debajo del mostrador o gabinete, y retire los materiales necesarios para facilitar la inserción y el desmontaje del gabinete del calefactor. 2. La unidad se afianza en su sitio atornillándola a través de los soportes laterales. Para que el montaje esté seguro, proporcione el material adecuado detrás del soporte lateral.
PAGE 9
MODELO 114 3. Instale el termostato desde el lado posterior del panel frontal y asegúrelo en su sitio, desde el frente, con los dos tornillos y arandelas incluidos (vea las figuras). 4. Conecte la perilla de control de temperatura empujándola suavemente en el eje del termostato. Para una instalación cor‑ recta, es necesario que se alineen las caras planas del eje y de la perilla (no trate de meter la perilla de control a la fuerza en el eje). 5.
PAGE 10
MODELO 114 Página 10 FUNCIONAMIENTO Antes de usar el calentador, asegúrese de que esté instalado ad‑ ecuadamente, de acuerdo con los pasos de instalación indicados en “PLANIFICACIÓN” en la página 7. 1. Gire el termostato en el sentido contrario de las agujas del reloj hasta su ajuste más bajo. 2. Encienda la energía eléctrica del circuito en la entrada de servicio. 3. Gire el termostato en el sentido de las agujas del reloj. De‑ berán encenderse el elemento calefactor y el ventilador.
PAGE 11
MODELO 114 Página 11 MANTENIMIENTO El usuario puede realizar las siguientes tareas de mantenimiento y limpieza. Todos los demás servicios los debe realizar un técnico autorizado. Si tiene preguntas, consulte a nuestro departamento de servicio al cliente llamando al: 800-558-1711. LUBRICACIÓN El calentador está permanentemente lubricado y nunca necesitará ponerle aceite ni desarmarlo. LIMPIEZA Limpie el calentador una vez al mes tal como sigue: 1. Apague la energía eléctrica en el panel de servicio. 2.
PAGE 12
MODELO 114 PIEZAS DE REPUESTO CLAVE No.