Installation Guide

3
FIG. 8
BLACK
NEGRO
BLACK
NEGRO
BLACK
NEGRO
BLACK
NEGRO
BLACK
NEGRO
WHITE
BLANCO
WHITE
BLANCO
WHITE
BLANCO
THERMAL
OVERLOAD
SOBRECARGA
TERMICA
HEATING
ELEMENT
ELEMENTO
DE CALOR
M
FIG. 9 - HALF-WATTAGE CONVERSION
CONVERSIÓN DE MEDIO VATIAJE
FIG. 10 - 120VAC TO 240VAC CONVERSION
CONVERSIÓN DE 120VCA A 240VCA
FIG. 11
THERMAL
OVERLOAD
SOBRECARGA
TERMICA
BLACK
NEGRO
BLACK
NEGRO
M
WHITE
BLANCO
CONVERTED 240 VAC HEATER
CALENTADOR CONVERTIDO
240 VCA
BLACK
NEGRO
WHITE
BLANCO
WHITE
BLANCO
WHITE
BLANCO
WHITE
BLANCO
BLACK
NEGRO
BLACK
NEGRO
DISCONNECT FOR HALF-
WATTAGE
DESCONECTE PARA MEDIO
VATIAJE
BLACK
NEGRO
FACTORY-WIRED
HEATER
(FULL WATTAGE)
CALENTADOR
CABLEADO DE
FABRICA (VATIAJE
COMPLETO)
HEATING
ELEMENT
ELEMENTO
DE CALOR
BLACK
NEGRO
LINE IN LINEA DE ENTRADA 240VCA
(2) BLACK WIRES (connected to motor)
(2) CABLES NEGROS (conectados al motor)
BLACK WIRE (from motor)
CABLE NEGRO (del motor)
WHITE WIRES
CABLES BLANCOS
MOTOR
MOTOR
INSTALLATION
WARNING: To reduce the risk of fire, do not store or
use gasoline or other flammable vapors and liquids
in the vicinity of the heater.
CAUTION: High temperature, risk of fire, keep
electrical cords, drapery, furnishings, and other
combustibles at least 3 feet (0.9 m) from the front of
the heater and away from the side and rear.
(16"-ON-CENTER STUDS ONLY)
NOTE: Locate housing at least 6" from the floor and
any adjacent walls.
1. Choose which side of housing will be mounted di-
rectly to a wall stud. Then insert a mounting bracket
from the opposite side into the channel at the top
of the housing. (FIG. 4)
2. Use measuring guide on side of housing to posi-
tion housing so that it will be flush with finished
wall. Drive to (2) nails through the holes on side of
housing and into stud. (FIG. 5)
3. Extend mounting bracket, level housing, and nail
to other stud. (FIG. 6)
(24"-ON-CENTER STUDS ONLY)
1. Choose which side of housing will be mounted
directly to a wall stud. From this side, push a mount-
ing bracket as far as possible into the channel at
the top of the housing.
NOTE: Locate housing at least 6" from the floor
and any adjacent walls.
2. Use measuring guide on side of housing to posi-
tion housing so that it will be flush with finished
wall. Drive two (2) nails through the holes in side
of housing and into stud. (FIG. 7)
3. Secure the two (2) mounting brackets together (with
screw supplied). Level housing and nail to opposite
stud, as shown.
WIRING
(ALL INSTALLATIONS)
1. Feed electrical power cable through open knockout
in corner of housing and attach with appropriate
connector. Allow 6" of wire inside of housing.
NOTE: Use other housing knockout when wiring
units in parallel.
2. Connect black to black, white to white, green to
green or bare wire. Replace wiring cover. (FIG. 8)
OPTIONAL WIRING
CONVERSIONS
(FIGS. 9, 10, 11)
1. Conversion to half-wattage. (FIG. 9)
The heater will produce less heat and use less
electricity if converted to half-wattage.
Disconnect ONE of the two (2) black wires (with
insulated terminals) from the motor.
2. 120 VAC to 240 VAC Conversion (FIGS. 10 &
11)
(Factory-wired 120 VAC Models 120 and 124 ONLY)
These heaters can be converted to operate on
240 VAC.
1) Disconnect ONE of the two (2) black wires (with
insulated terminals) from the motor.
2) Disconnect the two (2) white wires (with insu-
lated terminals) from each other. Do not remove
the white wire from beneath plastic wire tie.
3) Connect the black wire to the white wire.
NOTE: When heater is converted from 120 VAC to
240 VAC, half-wattage conversion is not possible.
INSTALACION
ADVERTENCIA: Para reducir el riesgo de incendio, no
almacene ni use gasolina u otros vapores y líquidos
flamables en las cercanías del calentador.
PRECAUCIÓN: Temperatura alta, el riesgo de incendio,
mantenga los cables eléctricos, cortinas, muebles y otros
materiales combustibles por lo menos 3 pies (0,9 m) del
frente del calentador y lejos de la cara y la parte trasera.
(VIGAS DE 40,64 CM DE CENTRO SOLAMENTE)
NOTA: sitúe la caja a no menos de 15,24 cm (6 pulg.) del
piso o cualquier pared adyacente.
1. Elija cuál lado de la caja se va a montar directamente
a una viga de la pared. Después, meta un soporte de
montaje, desde el lado opuesto, dentro del canal en la
parte superior de la caja. (FIG. 4)
2. Use la guía de medida que está en el lado de la caja
para colocar ésta a nivel con la pared terminada. Pase
dos (2) clavos por los agujeros en el costado de la caja
y clávelos en la viga de la pared. (FIG. 5)
3. Extienda los soportes de montaje, nivele la caja, y clave
a la otra viga. (FIG. 6)
(VIGAS DE 60,96 CM (24 PULG.) DE CENTRO)
1. Elija cuál lado de la caja se va a montar directamente
a la viga de la pared. Desde este lado, meta un soporte
de montaje hasta lo más profundo que se pueda dentro
del canal en la parte superior de la caja.
NOTA: sitúe la caja cuando menos 15,24 cm (6 pulg.)
del piso y cualquier pared cercana.
2. Use la guía de medida que está en un costado de la caja
para colocar ésta para que quede a nivel con la pared
terminada. Pase dos (2) clavos por los agujeros en el lado
de la caja y clávelos en la viga de la pared. (FIG. 7)
3. Fije los dos (2) soportes de montaje juntos (con el tornillo
que se incluye). Nivele la caja y clávela a la viga opuesta,
tal como se muestra.
CABLEANDO
(TODAS LAS INSTALACIONES)
1. Traiga el cable de energía eléctrica por la abertura del
disco removible en una esquina de la caja y fije con el
conector apropiado. Deje 15,24 cm (6 pulg.) de cable
dentro de la caja.
NOTA: use otro disco removible cuando cablee unidades
en paralelo.
2. Conecte negro a negro, blanco a blanco, verde a verde
o a cable desnudo. Coloque de nuevo la cubierta de
cableado. (FIG. 8)
CONVERSIONES DE
CABLEADO OPCIO-
NALES (FIGS. 9, 10, 11)
1. Conversión a medio vatiaje (FIG. 9)
El calentador produce menos calor y usa menos
electricidad si se convierte a medio vatiaje.
Desconecte del motor UNO de los dos (2) cables negros
(que tienen terminals aisladas).
2. Conversión de 120 VCA a 240 VCA (FIGS. 10 y 11)
(Solamente modelos 120 y 124 cableados de fábrica
para 120 VCA).
Estos calentadores de pueden convertir para que
funcionen en 240 VCA.
1) Desconecte del motor UNO de los dos (2) cables negros
(que tienen terminal aislada).
2) Desconecte los dos (2) cables blancos (con terminales
aisladas). No saque el cable blanco debajo del enlace
de cable plástico.
3) Conecte el cable negro al cable blanco.
NOTA: cuando el calentador se convierte de 120 VCA a
240 VCA, no es posible convertir a medio vatiaje.
LINE IN LINEA DE ENTRADA
GROUND
TIERRA
GROUND
TIERRA