Installation Guide

ManualsBrandsBroan ManualsVentilation Hood331H

Page Lm1

MODEL

331H

or 332H

EXTERIOR

BLOWER

WALL HOOD

CANOPY

(island canopy

available)

10" ROUND DUCT

SOFFIT

ROUGH-IN

PLATE

24" or 27"

18"

10" ROUND ELBOW

DUCT

OPENING

COVER PLATE

MODEL

331H

or 332H

EXTERIOR

BLOWER

WALL HOOD

CANOPY

(island canopy

available)

10" ROUND DUCT

SOFFIT

ROUGH-IN

PLATE

24" or 27"

18"

DUCT

OPENING

COVER

PLATE

MODEL 331H or 332H

EXTERIOR BLOWER

WALL HOOD

CANOPY

(island canopy

available)

10" ROUND

DUCT

SOFFIT

24" or 27"

18"

ROUGH-IN

PLATE

DUCT

OPENING

COVER PLATE

READ AND SAVE THESE INSTRUC

TIONS

FOR USE WITH RANGEMASTER HOODS AND ECLIPSE DOWNDRAFT VENTILATORS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equip-

ment to prevent backdrafting. Follow the heating equipment

manufacturer's guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code authori-

ties.

5. When cutting or drilling into wall, or ceiling, do not damage

electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce risk of fire, use only metal ductwork.

8. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazard-

ous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. Please read specification label on product for further informa-

tion and requirements.

4. Electrical circuit, including speed control, (if used), must be

rated 6 AMPS minimum for Model 332H or 3 AMPS minimum

for Model 331H.

1. Locate the blower so the length of the duct run and number of

elbows and transitions needed are kept to a minimum.

Please note - when using blower with the Broan Eclipse

Downdraft: The downdraft has a 3¼" x 10" discharge. Tran-

sitions are available to connect it to the 10" round inlet on

this exterior-mounted blower.

ALL INSTALLATIONS

MODEL VOLTS AMPS CFM DUCT SIZE

331H 120 2.4 600 10 " DIA.

332H 120 5.7 900 10" DIA.

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 3

MODELS 331H & 332H

EXTERIOR MOUNTED BLOWER

SPECIFICATIONS

PLAN THE INSTALLATION

TYPICAL ROOF MOUNTED INSTALLATION

(Vertical discharge)

TYPICAL WALL MOUNTED INSTALLATION

(Vertical discharge - elbow to horizontal)

TYPICAL WALL MOUNTED INSTALLATION

(Horizontal discharge)

2. Where possible, blower should be centered between wall studs

or roof rafters.

3. Avoid pipes, wires, or other ductwork that may be running

through the wall.

4. Be sure that there is enough space for any transitions that may

be needed between the blower and the connecting ductwork.

5. For best performance, locate transitions nearest to ventilator

(i.e. downdraft).

NOTE: Horizontal discharge requires relocation of the duct opening

cover plate. See hood manual for instructions.

Summary of content (12 pages)

PAGE 1
MODELS 331H & 332H EXTERIOR MOUNTED BLOWER Page Lm 1 FOR USE WITH RANGEMASTER HOODS AND ECLIPSE DOWNDRAFT VENTILATORS READ AND SAVE THESE INSTRUCTIONS WARNING CAUTION TO REDUCETHE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2.
PAGE 2
PREPARE THE INSTALLATION LOCATION PREPARE THE INSTALLATION LOCATION 2 ROOF INSTALLATIONS WALL INSTALLATIONS 1. Locate the blower on the rear slope of the roof. Place it in a location to minimize duct run. The location should be free of obstacles (T.V. leads, electrical lines, etc.). Bear in mind, if the blower top is level with the roof peak, it will not be seen from the street. Keep this approximate location in mind as you work from within the attic. 1. Choose a position on the outside wall.
PAGE 3
INSTALL THE BLOWER INSTALL THE BLOWER 3 ROOF INSTALLATIONS WALL INSTALLATIONS 1. Remove roofing nails from the upper 2/3 of the shingles around the cutout area and carefully lift the shingles to allow the back flashing sheet on the blower housing to fit under them. 1. Place a large bead of caulk on the back side of the housing along the outer edge. 2. Center the blower ring in the 11" diameter hole, making sure that the 1-1/4" diameter electrical wiring hole aligns with the hole in the wiring box. 3.
PAGE 4
SERVICE PARTS 4 MODELS 332H & 331H 3 4 5 16 1 13 5 8 4 15 11 17 18 19 10 6 12 KEY NO. 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 PART NO. DESCRIPTION 97011795 98008507 93260454 99100484 99260477 98008511 99100379 99080396 99080397 98008509 98008588 98008510 99020263 99020264 99140145 99400055 99100517 99150471 99150535 99271110 Airbox Assembly Damper Sheet Metal Nut, #18-18 U-Type (7 req.)* Isolator (3 req.) Whiz Nut, 1/4" - 20 (3 req.)* Grille Heyco Damper (2 req.
PAGE 5
MODÈLES 331H & 332H VENTILATEUR À MONTAGE EXTÉRIEUR Page Lm 5 POUR UTILISATION AVEC LES HOTTES RANGEMASTER ET LES VENTILATEURS ENCASTRÉS ECLIPSE VEUILLEZ LIRE CES DIRECTIVES ET LES CONSERVER AVERTISSEMENT ATTENTION OBSERVEZ LES DIRECTIVES CI-DESSOUS DE MANIÈRE À RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES CORPORELLES. 1. N’utilisez cet appareil qu’aux fins prévues par le fabricant.
PAGE 6
PRÉPAREZ L'ENDROIT POUR L'INSTALLATION PRÉPAREZ L'ENDROIT POUR L'INSTALLATION INSTALLATIONS MURALES INSTALLATIONS SUR LE TOIT Positionnez le ventilateur sur la pente arrière du toit. Placezle dans un endroit qui minimisera la longueur du conduit de ventilation. Cet endroit doit être exempt d'obstacles (câble de téléviseur, lignes électriques, etc.) Souvenez-vous que si le dessus du ventilateur est à ras de la pointe du toit, il ne sera pas vu de la rue.
PAGE 7
POSE DU VENTILATEUR Page Lm 7 INSTALLATION DU VENTILATEUR POSE DU VENTILATEUR POSE SUR UN MUR 1. Retirez les premiers deux tiers des clous à toiture des bardeaux se trouvant autour de la surface de découpe puis soulevez délicatement les bardeaux afin de glisser le solin en dessous. 1. Appliquez une large bande de produit à calfeutrer à l’arrière du boîtier, le long du rebord extérieur. 2.
PAGE 8
PIÈCES DE RECHANGE 8 MODÈLES 332H ET 331H 3 4 5 16 1 13 5 8 4 15 11 17 18 19 10 6 12 REPÈRE N° PIÈCE DESCRIPTION 1 2 3 4 5 6 7 8 97011795 98008507 93260454 99100484 99260477 98008511 99100379 99080396 99080397 98008509 98008588 98008510 99020263 99020264 99140145 99400055 99100517 99150471 99150535 99271110 Boîte à air Clapet Écrou à tôle, n° 18-18 Type U (7)* Isolateur (3) Écrou à rondelle, 1/4" - 20 (3)* Grille Butée de clapet (2) Moteur à condensateur (modèle 332H) Moteur à condensa
PAGE 9
MODELOS 331H Y 332H VENTILADOR DE MONTAJE EXTERIOR Page Lm 9 PARA USARSE CON CAMPANAS RANGEMASTER Y VENTILADORES ECLIPSE DE TIRO DESCENDENTE LEA Y CONSERVE ESTAS INSTRUCCIONES ADVERTENCIA PRECAUCIÓN PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS O LESIONES PERSONALES OBSERVE LAS SIGUIENTES PRECAUCIONES: 1. Use la unidad sólo de la manera indicada por el fabricante. Si tiene preguntas, comuníquese con el fabricante en la dirección o el número telefónico que se incluye en la garantía. 2.
PAGE 10
PREPARE EL LUGAR DE LA INSTALACIÓN PREPARE EL LUGAR DE LA INSTALACIÓN INSTALACIONES EN EL TECHO INSTALACIONES EN LA PARED Ubique el ventilador en la pendiente posterior del techo. Colóquelo en un área en la cual minimice la longitud del tramo de conductos. Esta área debe estar libre de obstáculos (cables de T.V., cables eléctricos, etc.). Recuerde que si la parte superior del ventilador está al ras del pico del techo, no se verá desde la calle.
PAGE 11
INSTALE EL VENTILADOR INSTALE EL VENTILADOR INSTALACIONES EN EL TECHO 1. Quite los clavos del techo de las 2/3 partes de las tejas superiores que se encuentran alrededor del área de corte y levante las tejas con cuidado para permitir que la hoja cubrejuntas posterior de la cubierta del ventilador se ajuste debajo de ellas. 2. Centre el anillo del ventilador en el orificio de 11" (27.9 cm), asegurándose de que el orificio del cableado eléctrico, de 1 ¼” (3.
PAGE 12
PIEZAS DE REPUESTO 12 MODELOS 331H Y 332H 3 4 5 16 1 13 5 8 4 15 11 17 18 19 10 12 CLAVE N.º 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 PIEZA Nº. 97011795 98008507 93260454 99100484 99260477 98008511 99100379 99080396 99080397 98008509 98008588 98008510 99020263 99020264 99140145 99400055 99100517 99150471 99150535 99271110 6 DESCRIPCIÓN Conjunto de la caja de ventilación Regulador de tiro Tuerca para metales, #18-18 tipo U (7 req.)* Aislador (3 req.) Tuerca Whiz, 1/4" - 20 (3 req.