Installation Guide

ManualsBrandsBroan ManualsVentilation Hood331H

BReAN

MODELS 331H & 332H

EXTERIOR MOUNTEDBLOWER

FOR USE WiTH RANGEIVlASTER HOODS AND ECLIPSE DOWNDRAFT VENTILATORS

WARNING CAUTION

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufac-

turer. If you have questions, contact the manufacturer at the

address or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as atag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhaust-

ing of gases through the flue (chimney) of fuel burning

equipment to prevent backdrafting. Follow the heating equip-

ment manufacturer's guideline and safety standards such as

those published by the National Fire Protection Association

(NFPA), and the American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE), and the local

code authorities.

5. When cutting or drilling into wall, or ceiling, do not damage

electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce risk of fire, use only metal ductwork.

8. This unit must be grounded.

1. For general ventilating use only. Do not use to exhaust

hazardous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. Please read specification label on product for further informa-

tion and requirements.

4. Electrical circuit, including speed control, (if used), must be

rated 6 AMPS minimum for Model 332H or 3 AMPS minimum

for Model 331H.

SPECiFiCATiONS

MODEL VOLTS AMPS

331H 120 2.4

332H 120 5.7

CFM DUCT SIZE

600 10 " DIA.

900 10" DIA.

PLAN THE INSTALLATION

Locate the blower so the length of the duct run and number of

elbows and transitions needed are kept to a minimum.

Please note = when using blower with the Broan Eclipse

Downdraft: The downdraft has a 31A'' x 10" discharge.

Transitions are available to connect it to the 10" round

inlet on this exterior=mounted blower.

2. Where possible, blower should be centered between wall

studs or roof rafters.

3. Avoid pipes, wires, or other ductwork that may be running

through the wall.

4. Be sure that there is enough space for any transitions that may

be needed between the blower and the connecting ductwork.

5. For best performance, locate transitions nearest to ventilator

(i.e. downdraft).

NOTE: Horizontal discharge requires relocation of the duct open-

ing cover plate. See hood manual for instructions.

MODEL 331H or 332H

EXTERIOR BLOWER

10" ROUND

DUCT

PLATE

IO"ROUNDELBOW

lO"ROUND DUCT

MODEL

WALL HOOD 331H

CANOPY or 332H

(island canopy EXTERIOR

available) BLOWER

DUCT

ROUGH-IN

PLATE

10"ROUND DUCT

DUCT

WALL HOOD OPENING

CANOPY COVER

(island canopy PLATE

available) MODEL

331H

18"

or 332H

EXTERIOR

BLOWER

24" or 27"

PLATE

TYPICAL ROOFMOUNTEDINSTALLATION

(Verticaldischarge)

TYPICALWALL MOUNTEDINSTALLATION

(Verticaldischarge- elbow to horizontal)

TYPICALWALLMOUNTEDINSTALLATION

(Horizontaldischarge)

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 3

Summary of content (12 pages)

PAGE 1
BReAN MODELS 331H & 332H EXTERIOR MOUNTED BLOWER FOR USE WiTH RANGEIVlASTER HOODS AND ECLIPSE DOWNDRAFT WARNING CAUTION TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2.
PAGE 2
PREPARE THE INSTALLATION LOCATION . PREPARE THE INSTALLATION LOCATION Locate the blower on the rear slope of the roof. Place it in a location to minimize duct run. The location should be free of obstacles (T.V. leads, electrical lines, etc.). Bear in mind, if the blower top is level with the roof peak, it will not be seen from the street. Keep this approximate location in mind as you work from within the attic. 2 1. Choose a position on the outside wall.
PAGE 3
iNSTALL THE BLOWER INSTALL 1. Remove 1. Place a large bead of caulk on the back side of the housing along the outer edge. roofing nails from the upper 2/3 of the shingles around the cutout area and carefully lift the shingles to allow the back flashing sheet on the blower housing to fit under them. 2. Center the blower ring in the 11" diameter 2. Center the blower . Attach blower provided. 3. Attach the blower provided. to the roof with the six screws to the wall with the six screw heads.
PAGE 4
SERVICE MODELS PARTS 332H & 331H 3 \ 16 13 \ 5 12 BROAN-NUTONE KEY NO. 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 ONE YEAR LiMiTED WARRANTY Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase.
PAGE 5
BReAN 5 MODi LES 331H & 332H VENTILATEURA MONTAGEEXTERIEUR POUR UTIUSATION AVEC LES HOTTES RANGEMASTER ET LES VENTILATEURS ENCASTRI_S ECLIPSE AVERTISSEMENT ATTENTION OBSERVEZ LES DIRECTIVES CI-DESSOUS DE IVIANIERE A REDUIRE LES RISQUES D'INCENDIE, DE CHOC I_LECTRIQUE OU DE BLESSURES CORPORELLES. 1. N'utJlisez cet appareil qu'aux fins pr_vues par le fabricant. Si vous 1. 2. 3. 4. 5. 6. 7. 8.
PAGE 6
PREPAREZ L'ENDROIT L'INSTALLATION POUR PREPAREZ L'ENDROIT L'INSTALLATION Positionnez le ventilateur sur la pente arriere du toit. Placezle dans un endroit qui minimisera la Iongueur du conduit de ventilation. Cet endroit doit _tre exempt d'obstacles (c&ble de televiseur, lignes electriques, etc.) Souvenez-vous que si le dessus du ventilateur est a ras de la pointe du toit, il ne sera pas vu de la rue. Souvenez-vous de cet emplacement approximatif pendant que vous travaillez de rinterieur de rentre-toit.
PAGE 7
POSE DU VENTILATEUR INSTALLATION DU VENTILATEUR 7 1. Retirez les premiers deux tiers des clous & toiture des bardeaux se trouvant autour de la surface de decoupe puis soulevez delicatement les bardeaux afin de glisser le solin en dessous. 1, Appliquez une large bande de produit & calfeutrer & I'arri_re du boftier, le long du rebord exterieur.
PAGE 8
PU CES DE RECHANGE MODI_LES 8 332H ET 331H 3 \ 5 16 \ 13 G \ 5 8 7 12 GARANTE REPERE N ° PIECE I 2 3 4 5 6 7 8 97011795 98008507 93260454 99100484 99260477 98008511 99100379 99080396 99080397 98008509 98008588 98008510 99020263 99020264 99140145 99400055 99100517 99150471 99150535 99271110 10 11 12 13 14 15 16 17 18 19 DESCRiPTiON Bofte & air Clapet E_crou & t61e, n ° 18-18 Type U (7)* Isolateur (3) E_crou & rondelle, 1/4" - 20 (3)* Grille Butee de clapet (2) Moteur & condensateur (modele
PAGE 9
BReAN PARA USARSE CON CAMPANAS RANGEMASTER Y VENTILADORES ADVERTENCIA PARA REDUClR O LESlONES PRECAUClONES: 1. 2. 3. 4. 5. 6. 7. 8. ECLIPSE DE TIRe DESCENDENTE PRECAUCION EL RIESGO DE INCENDIOS, DESCARGAS PERSONALES OBSERVE LAS ELleCTRICAS SlGUIENTES 1. 2. Use la unidad s61e de la manera indicada per el fabdcante. Si tiene preguntas, comuniquese con el fabricante en la direcci6n o el n_mere telef6nico que se incluye en la garantia.
PAGE 10
PREPARE EL LUGAR DE LA INSTALAClON PREPARE EL LUGAR DE LA INSTALAClON Ubique el ventilador en la pendiente posterior del techo. Col6quelo en un Area en la cual minimice la Iongitud del tramo de conductos. Esta Area debe estar libre de obstaculos (cables de T.V., cables el_ctricos, etc.). Recuerde que si la parte superior del ventilador esta al ras del pico del techo, no se vera desde la calle. Mantenga en mente esta ubicaci6n aproximada mientras trabaja desde el atico. 1. 1.
PAGE 11
INSTALE EL VENTILADOR 1. Quite los superiores davos del techo de las 2/3 que se encuentran alrededor INSTALE partes de las tejas del Area de corte y 3. Monte el ventilador en el techo con los seis tornillos que Coloque un reborde grande de material de calafateo en el lado posterior de la cubierta, a Io largo del borde externo. 2. Centre el anillo del ventilador en el orificio de 11" (27.9 cm), asegurandose de que el orificio del cableado el_ctrico, de 1 1A" (3.
PAGE 12
PIEZAS DE REPUESTO MODELOS !2 331H Y 332H 3 \ 16 13 \ 5 15 17 12 6 GARANTIA CLAVE N. 9 1 2 3 4 5 6 7 8 10 11 12 13 14 15 16 17 18 19 PIEZA N 9. DESCRIPClON 97011795 98008507 93260454 99100484 99260477 98008511 99100379 99080396 99080397 98008509 98008588 98008510 99020263 99020264 99140145 99400055 99100517 99150471 99150535 99271110 Conjunto de la caja de ventilaciSn Regulador de tiro Tuerca para metales, #18-18 tipo U (7 req.)* Aislador (3 req.) Tuerca Whiz, 1/4" - 20 (3 req.