INSTALLATION INSTRUCTIONS HB0091 EC62 SERIES ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGE 12. Broan-NuTone Canada Inc.; Mississauga, Ontario www.broan.ca 877-896-1119 www.broan.ca REGISTER YOUR PRODUCT ON LINE AT: www.broan.ca SV08970 rev.
! WARNING ! WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*: 1. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.
- EC62 SERIES STANDARD 3¼” X 10” ROOF CAP (NOT INCLUDED) POWER PACK SYSTEM - STANDARD 3¼” X 10” WALL CAP (NOT INCLUDED) MODEL 437 HIGH CAPACITY ROOF CAP (NOT INCLUDED) MODEL 441 10” ROUND WALL CAP (NOT INCLUDED) MODEL 418 10” ROUND ADJUSTABLE ELBOW (NOT INCLUDED) MODEL 410 10” ROUND DUCT — 2 FT.
1. PREPARE THE INSTALLATION ! WARNING When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: - Power Pack - Accessories: • 2 Filters • 2 Filter knobs with screws, taped inside the hood • 2 Shielded halogen lamps (120 V, 50 W max.
3. PREPARE CUSTOM HOOD ! WARNING When building a custom hood, always follow all applicable construction codes and standards. The custom hood must be positively secured to wall studs or other wooden framework behind the drywall. Make sure it is capable of supporting its own weight and the weight of the power pack. Failure to do so may cause personal injury or damage to countertop or cooktop. The custom hood must be constructed to fit the shape and total weight of the EC62 power pack model.
4. INSTALL CUSTOM HOOD LINER (OPTIONAL) The liners are specially designed to protect the exterior base of the custom hood. To order, refer to the table below to find the right liner model number according to the width of the custom hood nominal width. To view specific model information, including depths for each liner models, visit www.broan.ca or contact Technical Support (phone number listed on front cover). To install, see instruction packed with custom hood liner.
8. REMOVE WIRING COVER AND FRONT PANEL Using a Robertson or a Phillips no. 2 screwdriver, remove both wiring cover retaining screws (A). Detach it from the power pack and set aside with its screws. Then, remove both sides screws (B) retaining the front panel to the power pack. Carefully detach the front panel from the power pack and set aside with its screws. A B HD0365 9.
12. INSTALL THE ADAPTER AND THE DAMPER (DUAL BLOWER MODEL ONLY) MOUNTING SCREW LOCATION Using 2 no. 8 x 3/8’’ screws from parts bag, assemble the adapter on the top of the power pack. Seal all joints with metal foil duct tape to eliminate air leaks. HJ0035 Install 10” damper inside the VERTICAL ductwork that will be attached to power pack. Do not install in a horizontal ductwork or it will not open and close properly. Remove shipping tape if present.
14. INSTALL THE POWER PACK CAUTION Take care not to kink ducting or pinch electrical cable when installing the power pack. CLASPING SPRINGS Lift the power pack in custom hood until the bottom of the clasping springs (2 per side) rests on the top of the custom hood base (grey zone in illustration at right). HD0370 From inside the power pack, using provided no. 8-10 x 1/2” screws, mount the power pack to the custom hood base.
16. REINSTALL THE BLOWER (SINGLE BLOWER MODEL, HORIZONTAL DISCHARGE ONLY) The single blower power pack is factory shipped for a vertical discharge installation. For a horizontal discharge installation, the blower must be flipped. Using a 5/16” socket, or a Phillips no. 2 or a Robertson no. 2 screwdriver, secure the blower to the inner back of the power pack with all blower mounting screws (previously removed in step 13).
18. CONNECT WIRING (ALL MODELS) (CONT’D) A Connect cable using provided wire connectors. Connect wires as follow: BLACK to BLACK, WHITE to WHITE and GREEN or BARE wire under ground screw (A). DO NOT FORGET TO CONNECT THE GROUND. HE0059 19. REINSTALL FILTERS CAUTION Remove protective plastic film covering filters before installing them. 1. Using a Phillips no. 2 screwdriver, assemble the knob to each filter. NOTE: The screw MUST BE on filter tabs side. See illustration at right. HO0139 2.
21. USE AND CARE Filters The filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates more grease — like frying foods or wok cooking. Remove filters by pushing it towards the back of power pack and rotating filter downward. Filters are dishwasher safe. Allow filters to dry completely before reinstalling them in the power pack. Clean all-metal filters in the dishwasher using a non-phosphate detergent.
120 VAC 23. WIRING DIAGRAM BLK LINE WHT NEUTRAL GROUND Q1 TRANSFORMER LOGIC LAMP WHT RED 9.
25.SERVICE PARTS EC621306SS EC622301SS 1 1 11 11 10 2 3 3 4 4 9 5 6 10 2 5 8 6 7 9 8 7 HL0169 KEY NO. PART NO.