Installation Guide

99043316A
INSTALLATION INSTRUCTIONS
•
ALL ELECTRICAL CONNECTIONS MUST BE IN ACCORDANCE WITH LOCAL
CODES, ORDINANCES, OR NATIONAL ELECTRICAL CODE, AS APPLICABLE.
FOR SAFETY, THIS PRODUCT MUST BE GROUNDED. IF YOU ARE UNFAMILIAR
WITH METHODS OF INSTALLING ELECTRICAL WIRING, SECURE THE SER-
VICES OF A QUALIFIED ELECTRICIAN.
•
Turn off power and lock out sevice panel before installing, wiring, or servicing this product.
•
To prevent serious injury from electrical shock or damage to electrical components - DO NOT
WIRE HOT!
•
Warranty is void if miswired.
1. Turn off power and lock out service panel before wiring control.
2. Install a 2½" deep switch box if using 14-gauge wire. Install a 2¾" deep switch box if using
12-gauge wire.
(Single-gang box for time control only. Double-gang box for time control
w/rocker switch.)
3. Attach incoming power line and fan power line to switch box. It may be necessary to use
two side knockouts for some applications.
4. Make electrical connections as shown. Use proper electrical connectors. Make sure that
time control, (rocker switch) and applicance are properly grounded.
5. Tuck wires into box. Fasten time control (and rocker switch) to box with mounting screws.
Note "TOP" direction shown on time control face.
6. Attach switch plate using color-matched oval head screws.
7. Slip the time dial plate over the threaded extension with "OFF" mark at top. Fasten
with nut. DO NOT OVERTIGHTEN.
8. Push knob onto time control shaft. The knob has a "D-shaped" hole which matches the
"D-shaped" shaft on the time control.
WIRING DIAGRAMS
BROAN-NUTONE ONE YEAR LIMITED WARRANTY
Broan-NuTone warrants to the original consumer purchaser of its products that such products will be free from defects
in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which
is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND TUBES. This warranty does
not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse,
negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation
contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some
states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE’S OPTION, SHALL BE THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE SHALL NOT BE
LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION
WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This
warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify Broan-NuTone, (b) give the model number and part identification
and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must
present evidence of the original purchase date.
Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)
Broan-NuTone Canada, Inc., 1140 TriStar Drive, Mississauga, Ontario L5T 1H9 (1-888-882-7626)
TIME CONTROL OPERATING INSTRUCTIONS
Depending on model, time control will operate fan at any interval from 1 minute up to 15 minutes,
1 minute up to 60 minutes, or 1 hour to 12 hours. Turn indicator knob past "TURN PAST" and
then to desired time setting. Timer will automatically shut fan off at the end of the set time period.
Timer will provide continuous fan operation when indicator knob is turned to "HOLD" position.
(Not on 15-min. time control).
TIME CONTROL W/ DUAL ROCKER SWITCH
TIME CONTROL W/ ROCKER SWITCH
* CODE REQUIRES BOTH ENDS OF THIS WIRE BE COLORED
SINCE IT IS SWITCHED. USE A FELT-TIPPED MARKER.
120 VAC
LINE IN
WHITE
GROUND
SWITCH BOX APPLIANCE
BLACK
RED
LOAD
1
WHITE *
GROUND
WHITE
LOAD
2
LOAD
3
TIME
CONTROL
BLACK
NOC
CNC 1
2
2
1
DUAL
ROCKER
SWITCH
120 VAC
LINE IN
WHITE
GROUND
SWITCH BOX APPLIANCE
BLACK
RED
LOAD
1
GROUND
WHITE
BLACK
LOAD
2
NOC
CNC 1
2
2
1
ROCKER
SWITCH
TIME
CONTROL
LOAD
TIME
CONTROL
1
NO
1
C
2
C
2
NC
BLACK
WHITE
GROUND
WHITE
BLACK
GROUND
SWITCH BOX APPLIANCE
120 VAC
LINE IN
OR
LOW VOLTAGE
SOURCE
(30V OR LESS)
TIME CONTROL
Time Control w/ Dual Rocker Switch and double-gang switch box shown.
TIME DIAL
PLATE
NUT
KNOB
COLOR-MATCHED
OVAL-HEAD
SCREW (2 or 4)
MOUNTING
SCREW (2 or 4)
TERMINAL SCREW WITH
PRESSURE PLATE (2)
TIME CONTROL
THREADED
EXTENSION
STANDARD 2-1/2" MIN.
DEPTH SWITCH BOX
SWITCH PLATE
TIME CONTROL • TIME CONTROL W/ ROCKER SWITCH
• TIME CONTROL W/ DUAL ROCKER SWITCH
IMPORTANT NOTE
The time control is designed with "NO" (Normally Open) and "NC"
(Normally Closed) contacts. The standard installation uses the
"NO" contacts (see wiring diagrams below).