Instructions / Assembly

ManualsBrandsBroan ManualsBath Fans100 CFM Exhaust Fan with Light/Night Light

Page 1

MODEL 750

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-

JURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a promi-

nent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a quali-

fied person(s) in accordance with all applicable codes and stan-

dards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code authori-

ties.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be marked

as appropriate for the application and be connected to a GFCI

(Ground Fault Circuit Interrupter) - protected branch circuit.

8. Never place a switch where it can be reached from a tub or

shower.

9. To reduce the risk of electrical shock, do not use this fan with

any solid-state speed control.

10. Not for use in kitchens.

11. Do not install in a ceiling insulated to a value greater than R-40.

12. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazard-

ous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. Please read specification label on product for further informa-

tion and requirements.

FAN / LIGHT / NIGHT LIGHT

COMBINATION VENTILATOR

READ AND SAVE THESE INSTRUCTIONS

FOR BEST RESULTS

When installing the Exhaust Fan/Light in a new construction site,

install housing during the rough-in construction of the building.

The blower unit, reflector and grille should be installed after the

finished ceiling is in place.

PLANNING DUCTWORK AND WIRING

DUCTWORK

1. Use 4" round duct.

2. Plan duct run from discharge opening of fan to the outside. For

best fan performance, make duct run as short as possible and

use minimum number of elbows.

3. Use optional Broan ducting accessories as needed.

WIRING

Plan to run 120 VAC house wiring (with ground) from power source,

through wall switch, to junction box in housing. For separate con-

trol of fan, light, night light, three wall switches are required and

five conductors are needed between the wall switch box and the

fan’s junction box.

IMPORTANT: Use wire suitable for 90

Summary of content (8 pages)

PAGE 1
MODEL 750 Page 1 FAN / LIGHT / NIGHT LIGHT COMBINATION VENTILATOR READ AND SAVE THESE INSTRUCTIONS WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2.
PAGE 2
MODEL 750 Page 2 INSTALLATION IN A NEW CONSTRUCTION SITE PREPARATION 1. Refer to Figure 1. Remove power unit/blower assembly from housing. A. Unplug power unit. B. Remove screw (located next to plug-in receptacle) which holds power/blower unit mounting plate in place. Save screw. C. Lift mounting plate at end near the plug-in receptacle until blower wheel clears the scroll. D. Remove plate by pulling its tabs out of slots in housing. Set power/blower unit aside until needed.
PAGE 3
MODEL 750 Page 3 POWER/BLOWER UNIT INSTALLATION 1. Refer to Figure 1. Place power/blower unit into housing so that mounting plate’s tabs insert into slots in housing. 2. Press other end of mounting plate down until it is firmly seated over scroll and plug-in receptacles. 3. Secure mounting plate to housing with provided screw. 4. Insert motor plug into junction box receptacle. COMPLETING INSTALLATION 1.
PAGE 4
MODEL 750 USE AND CARE USE AND CARE WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND LOCK OUT SERVICE PANEL BEFORE RELAMPING, CLEANING, OR SERVICING THIS UNIT. CLEANING RELAMPING Page 4 Pull grille assembly away from ceiling. Squeeze the grille assembly’s mounting springs together, and remove grille asembly from housing for cleaning. Pull grille assembly away from ceiling. Clean grille and lens assembly using a mild soap and water solution. Assemblies with wood frames should not be immersed.
PAGE 5
MODEL 750 MODELO VENTILADOR / LUZ / LUZ DE NOCHE VENTILADOR COMBINACIÓN Página Page 5 LEA Y CONSERVE ESTAS INSTRUCCIONES ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIO, CHOQUE ELECTRICO, O LESION A PERSONAS, PROCURE LO SIGUIENTE: 1. Utilice esta unidad sólo en la manera prescrita por el fabricante. Si tiene usted alguna pregunta, comuníquese con el fabricante a la dirección o el teléfono indicados en la garantía. 2.
PAGE 6
MODEL 750 MODELO Página Page 6 INSTALACION EN UN LUGAR NUEVO DE CONSTRUCCION PREPARACION 1. Refiérase a la Figura 1. Saque el conjunto de la unidad de potencia/soplador de la caja. A. Desenchufe la unidad de potencia. B. Quite el tornillo (localizado junto al receptáculo de clavija) que sostiene la placa de montaje de la unidad de potencia/soplador en su sitio. Reserve el tornillo. C.
PAGE 7
MODEL 750 MODELO Página Page 7 INSTALACION DE LA UNIDAD DE POTENCIA/SOPLADOR 1. Refiérase a la Figura 1. Coloque la unidad de potencia/soplador en la caja para que las lengüetas de la placa de montaje se inserten en las ranuras de la caja. 2. Presione el otro extremo de la placa de montaje hasta que esté firmemente asentada sobre los receptáculos de espiral y de clavija. 3. Fije la placa de montaje a la caja con el tornillo provisto. 4. Inserte el enchufe del motor en el receptáculo de la caja de empalme.
PAGE 8
MODEL 750 MODELO USO Y CUIDADO USO Y CUIDADO AVERTISSEMENT : DÉBRANCHEZ L’ALIMENTATION ÉLECTRIQUE ET VERROUILLEZ LE PANNEAU D’ENTRÉE D’ÉLECTRICITÉ AVANT LE REMPLACEMENT DES LAMPES, LE NETTOYAGE OU LA RÉPARATION DE L’APPAREIL. LIMPIEZA CAMBIO DE BOMBILLAS Tire de la lente separándola del conjunto de reflector/rejilla. Aprete los muelles de montaje, y quite la lente para exponer el portalámparas para cambiar la bombilla.