Installation guide
13.
INSTALL
THE
HOOD
Hold
the
hood
until
it
is
completely
secured
to
the
wood
mounting
strip.
Mount|NG
SCREWS
LOCATION
INTERNAL
BLOWER(S)
ONLY
:°
Run
power
cable
to
installation
location.
Remove
the
electrical
compartment
cover.
|||
>=
Insert
the
cable
in
the
hood
and
tighten
the
wire
clamp
to
secure
the
cable.
6
‘e
ee
LI
=
Seen
pg
ee
ALL
INSTALLATIONS
upeees
Se
Rest
the
back
cavity
of
the
hood
on
the
wood
mounting
strip.
WALL
ANCHORS
LOCATION
Secure
the
hood
to
wood
mounting
strip
with
(4)
screws
no.
8 x
3/4”
(for
30”
and
36”
width
hoods)
or
(6)
screws
(for
42”
and
48”
width
hoods)
provided
at
locations
shown.
Drill
(3)
3/16”
size
holes
into
the
drywall
for
wall
anchors
through
the
existing
holes
in
the
inside
hood
back
in
the
locations
shown.
Then,
install
the
three
wall
anchors
with
the
remaining
no.
8 x
3/4”
screws
and
the
(3)
washers
provided.
For
a
non-ducted
installation,
go
to
step
15,
Connect
the
wiring.
14.
ROUGH-IN
PLATE
LOCATION
(EXTERNAL
BLOWERS
HOODS
ONLY)
Run
power
cable
to
installation
location.
For
ducting
through
top
of
hood,
existing
plate
remains
in
place
on
inside
back
of
hood.
For
ducting
through
back
of
hood,
remove
existing
plate
from
inside
back
of
hood
and
remove
the
rough-in
plate
from
the top
of
hood.
Attach
the
plate
to
inside
top
of
hood
to
cover
hole.
Secure
to
threaded
studs
with
same
(4)
nuts.
Install
the
rough-in
plate
to
the
back
of
hood
so
that
the
wiring
box
is
located
on
the
right
side
as
you
are
facing
the
hood.
Connect
ducting
to
rough-in
plate
as
you
are
installing
the
rough-in
plate.
Use
duct
tape
to
make
all
joints
secure
and
air-tight.
Ho0262
PLATE
ON
BACK
OF
HOOD
15.
CONNECT
THE
WIRING
(ALL
BLOWERS)
Risk
of
electric
shock.
Electrical
wiring
must
be
done
by
qualified
personnel
in
accordance
with
all
applicable
codes
and
standards.
Before
connecting
wires,
switch
power
off
at
service
panel
and
lock
service
disconnecting
means
to
prevent
power
to
be
switched
on
accidentally.
Remove
wiring
cover
from
rough-in
plate
or
electrical
compartment
and
set
aside.
INTERNAL
BLOWERS:
Connect
cable
into
wiring
box
using
wire
connectors.
Connect
BLACK
to
BLACK,
WHITE
to
WHITE
and
GREEN
or
bare
wire
under
GREEN
ground
screw.
The
ORANGE
wire
(A)
is
for
make-up
air
device
connection
only.
If
there
is
no
make-up
air
device,
never
remove
the
cap
on
the
ORANGE
wire
end.
Reinstall
wiring
cover.
IN-LINE
OR
EXTERIOR
BLOWERS:
See
instructions
included
with
blower.
HEooes
-1i-