Installation Sheet

ManualsBrandsBroan ManualsBroan Parts and AccessoriesBroan Occupancy Sensor Wall Control for Bathroom Exhaust Fan

1. The occupancy sensor wall switch turns lighting or fan loads on

and off based on occupancy and ambient light level. They are

designed to replace a standard light switch. The switch operates

with 120 to 277V AC line voltage.

2. The sensor uses passive infrared technology to sense human

motion, and defines it as occupancy. A red LED in the sensor

blinks upon occupancy and then resets. It will blink again when

it detects motion after the 2-second reset.

3. In Automatic ON & Automatic OFF mode, the sensor turns on

the load automatically when it detects occupancy. Once the

space is vacant and the time delay elapses, it turns off the load

automatically.

4. If adequate ambient light is already present in the area, the

sensor will hold off the load it controls. When the light drops

below a field selectable level and the sensor detects occupancy,

the sensor turns on the load.

MOUNTING LOCATION

The device responds to temperature changes and care should be

taken when mounting the device. Do not mount directly above a

heat source, in a location where hot or cold drafts will blow

directly on the sensor, or where unintended motion (e.g., hallway

traffic) will be within sensor’s field-of-view.

4A - INSTALLATION FOR SINGLE POLE

Slotted / Phillips Screwdriver Pencil

PREPARATION BEFORE INSTALLATION

Single-Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

Two Location Control

1. Line (Hot)

2. Neutral

3. Ground

4. Traveler (note color)

5. Load

If the wiring in the wall box does not resemble any of these

configurations, consult an electrician.

4. Before Wiring the Device:

1. Make sure that the ends of wires from the wall box are straight

(cut if necessary).

2. Remove 5/8" (1.6 cm) of insulation from each wire in the wall box.

3. Use wire connectors to join one 12 AWG supply wire with one or

two 16 AWG or 18 AWG, or to join one 14 AWG supply wire with

one to three 16 AWG or 18 AWG.

NOTE: Three wire connectors provided in the product

package are suitable for copper or copper clad wire only.

For single-pole applications, go to Step 4A.

For two location control applications, go to Step 4B.

Electrical Tape

Pliers

Cutters Ruler

1. Turn OFF Power:

Turn power OFF at circuit breaker (or remove fuse).

2. Remove Wallplate and Switch:

Remove wallplate and switch mouting screws. Carefully

remove switch from wall (do not remove wires).

3. Identify the Type of Circuit:

TOOLS NEEDED FOR INSTALLATION

UNIT FEATURES AND DESCRIPTION

WARNINGS AND CAUTIONS

1. CAUTION: To avoid overheating and possible damage to this

device and other equipment, DO NOT install to control a

receptacle.

2. To be installed and/or used in accordance with appropriate

electrical codes and regulations.

3. If you are unsure about any part of these instructions, consult an

electrician.

4. Use this device with copper or copper clad wire only.

5. Do not use this product to control

loads in excess of specified

ratings, or it may cause death, injury or property damage.

6. The sensing switch requires an unobstructed view of room

occupants to detect motion.

7. Hot objects or moving air currents can affect the performance of

the sensing switch.

8. For indoor use only. Operate between 32 to 104

F (0 to 40 °C).

9. Clean sensor with a piece of soft damp cloth only. Do not use

any chemical cleaners.

Hot (Black) Black

Black

White

Line 120VAC, 60HZ

Green Ground

Neutral (White)

Load

Connect wires per wiring diagram as follows:

1. Connect green ground or bare copper wire in the wall box to the

Green wire of the device.

2. Connect Hot wire in the wall box to the Black wire of the device.

3. Connect Load wire(s) in the wall box to the Red wire of the

device.

4. Screw wire connectors on clockwise making sure no bare

conductors show below the wire connectors. Secure each

connector with electrical tape.

5. Mount device in the wall box with screws and mount wall plate.

6. Restore power at circuit breaker or fuse. Installation is complete.

7. Turn on the power, manually press the switch button to check

whether the product is installed correctly, and at the same time

ensure that the LED light in the fresnel lens flashes. Wait about

40s for product booting, the product will work properly.

Green

Black

Red

Ground

Neutral

Hot

Load

Insert wires into

wire connectors

then twist

clockwise

Use electrical

tape to secure

wire connectors

and wires

Red

NOTE:

1. A ground connection is required to operate. Use the ground

wire in the wall box for ground connection. If no ground is

available, consult an electrician. Device will not function if it is

not grounded.

2. The hot (black wire) and load (red wire) must be correctly

connected as stated above, otherwise the device will not

function. If the light never turns on, then try to reverse the hot

and load wiring of the sensor.

Passive Infrared Occupancy Sensor Wall Switch

LED/CFL 300W, Incandescent 600W, 1/2 HP, 120~277VAC, 60Hz

INSTALLATION INSTRUCTIONS

Model No.:

MS100W (Occupancy Sensor)

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Passive Infrared Occupancy Sensor Wall Switch LED/CFL 300W, Incandescent 600W, 1/2 HP, 120~277VAC, 60Hz MOUNTING LOCATION 4A - INSTALLATION FOR SINGLE POLE The device responds to temperature changes and care should be taken when mounting the device. Do not mount directly above a heat source, in a location where hot or cold drafts will blow directly on the sensor, or where unintended motion (e.g., hallway traffic) will be within sensor’s field-of-view.
PAGE 2
4B - INSTALLATION FOR TWO LOCATION CONTROL PREPARATION FOR UNIT SETTING SETTING FOR DIFFERENT MODES Connect wires per wiring diagram as follows: 1. Pry off the top cover with a slotted screwdriver. 1. Connect green ground or bare copper wire in the wall box to the Green wire of the device. 2. Connect Hot wire in the wall box to the Black wire of the device. 3. Connect Load wire(s) and Traveler wire in the wall box wire to the Red wire of the device. 4.
PAGE 3
INSTRUCTIONS D’INSTALLATION Interrupteur mural avec détecteur de présence à infrarouge passif DEL ou ampoules fluocompactes : 300 W; Ampoules incandescentes : 600 W ½ HP, 120 à 277 V CA, 60 Hz EMPLACEMENT D’INSTALLATION 4A. INSTALLATION POUR CIRCUIT À UN INTERRUPTEUR L’appareil réagit aux changements de température; son emplacement doit donc être déterminé avec soin.
PAGE 4
B. INSTALLATION POUR CIRCUIT À DEUX INTERRUPTEURS PRÉPARATION DU RÉGLAGE RÉGLAGLE DES DIFFÉRENTES MODES Connecter les fils comme l’indique le schéma. 1. Ouvrir le couvercle avec un tournevis à pointe plate. 1. Connecter la mise à la terre en cuivre vert ou dénudé dans la boîte électrique au fil vert de l’appareil. 2. Connecter le fil de phase dans la boîte électrique au fil noir de l’appareil. 3.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN Interruptor de pared de sensor de ocupación infrarrojo pasivo LED/CFL 300W, Incandescente 600W, 1/2 HP, 120~277VAC, 60Hz UBICACIÓN DE MONTAJE 4A - INSTALACION PARA UNIPOLAR El dispositivo responde a los cambios de temperatura y se debe tener cuidado al montar el dispositivo.
PAGE 6
4B - INSTALACIÓN PARA CONTROL DE DOS UBICACIONES Conecte los cables según el diagrama de cableado de la siguiente manera: 1. Conecte la tierra verde o el cable de cobre desnudo de la caja de pared al cable verde del dispositivo. 2. Conecte el cable caliente de la caja de pared al cable negro del dispositivo. 3. Conecte los cables de carga y el cable Traveler en el cable de la caja de pared al cable rojo del dispositivo. 4.