Installation

ManualsBrandsBroan ManualsFansSSQTXE080

Page 1

MODELS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-

JURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equip-

ment to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code authori-

ties.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Acceptable for use over a tub or shower when connected to

a GFCI (Ground Fault Circuit Interrupter) - protected branch

circuit (ceiling installation only).

8. This unit must be grounded.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazard-

ous or explosive materials and vapors.

2. This product is designed for installation in ceilings up to a

12/12 pitch (45 degree angle). Duct connector must point up.

DO NOT MOUNT THIS PRODUCT IN A WALL.

3. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

4. Please read specification label on product for further informa-

tion and requirements.

QTXE SERIES

ULTRA SILENT

FANS

READ AND SAVE THESE INSTRUCTIONS

CLEANING & MAINTENANCE

Installer: Leave this manual with the homeowner.

For quiet and efficient operation, long life, and attractive appear-

ance - lower or remove grille and vacuum interior of unit with the

dusting brush attachment.

The motor is permanently lubricated and never needs oiling. If the

motor bearings are making excessive or unusual noises, replace

the blower assembly (includes motor and impeller).

OPERATION

Use an on/off switch or speed control to operate this ventilator. See

“Connect Wiring” for details.

Use of speed controls other than the

Broan Models 78V and 78W may cause a motor humming noise.

Summary of content (12 pages)

PAGE 1
MODELS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Page 1 QTXE SERIES ULTRA SILENT FANS TM READ AND SAVE THESE INSTRUCTIONS WARNING CLEANING & MAINTENANCE TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2.
PAGE 2
MODELS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Page 2 TYPICAL INSTALLATIONS Housing mounted to I-joists. Housing mounted anywhere between I-joists using hanger bars. Housing mounted anywhere between trusses using hanger bars. PLAN THE INSTALLATION COOKING AREA Do not install above or inside this area. 45o Housing mounted to joists. NOT FOR USE IN A COOKING AREA. 45o Cooking Equipment Floor INSULATION* (Place around and over Fan Housing.
PAGE 3
MODELS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Page 3 INSTALL HOUSING & DUCT 1a. Mount housing to joist or I-joist. Use a pliers to bend housing TABS out to 900. Hold housing in place so that the housing tabs contact the bottom of the joist. The housing mounts with four (4) screws or nails. Screw or nail housing to joist through lowest holes in each mounting flange, then through highest holes.
PAGE 4
MODELS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Page 4 CONNECT WIRING INSTALL GRILLE 5. Finish ceiling. Install ceiling material. Cut out around housing. 6. Attach grille to housing. Squeeze grille springs and insert them into slots on each side of housing. 7. Push grille against ceiling. 4. Connect electrical wiring. Run 120 VAC house wiring to installation location. Use proper UL approved connector to secure house wiring to wiring plate.
PAGE 5
MODÈLES QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Page 5 VENTILATEURS ULTRA SILENTMC (ULTRA SILENCIEUX) SÉRIE QTXE LISEZ CES DIRECTIVES ET CONSERVEZ-LES AVERTISSEMENT NETTOYAGE ET ENTRETIEN OBSERVEZ LES DIRECTIVES CI-DESSOUS AFIN DE RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES CORPORELLES : 1. N’utilisez cet appareil que de la manière prévue par le fabricant.
PAGE 6
MODÈLES QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Page 6 INSTALLATIONS TYPE Boîtier fixé à des solives en « I ». BLOC ESPACEUR DE SOLIVE EN « I » ERGOTS DE MONTAGE Boîtier monté n’importe où entre des fermes de toit à l’aide des barres de suspension. BARRES DE CÂBLE D'ALIMENTATION SUSPENSION (s’allongent jusqu’à 61 cm [24 po]) BOÎTIER CÂBLE D'ALIMENTATION BOÎTIER MATÉRIAU DU PLAFOND Boîtier monté n’importe où entre des solives en « I » à l’aide des barres de suspension.
PAGE 7
MODÈLES QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Page 7 INSTALLATION DU BOÎTIER ET DES CONDUITS 1a. Fixez le boîtier aux solives ou solives en I. Utilisez des pinces pour plier les ERGOTS vers l’extérieur à 90°. Maintenez le boîtier en place de sorte que les ergots touchent au bas de la solive. Le boîtier se fixe avec quatre (4) vis ou clous. Vissez ou clouez-le à la solive au travers des trous les plus bas de chaque bride de montage, puis au travers des trous les plus hauts.
PAGE 8
MODÈLES QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Page 8 CÂBLAGE INSTALLER LA GRILLE NOIR 5. Finissez la surface du plafond. NOIR Installez le matériau du plafond. Coupez-le autour du boîtier. INTERRUPTEUR MARCHE/ARRÊT BLANC 6. Fixez la grille au boîtier. NOIR ENTRÉE BLANC BLANC FIL DE TERRE FIL DE TERRE BOÎTE D'INTERRUPTEUR Pincez les ressorts de la grille et insérez-les dans les fentes de chaque côté du boîtier.
PAGE 9
MODELOS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Página 9 VENTILADORES ULTRA SILENCIOSOS SERIE QTXE LEA Y CONSERVE ESTAS INSTRUCCIONES ADVERTENCIA LIMPIEZA Y MANTENIMIENTO PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS O LESIONES PERSONALES, OBSERVE LAS SIGUIENTES PRECAUCIONES: 1. Use la unidad sólo de la manera indicada por el fabricante. Si tiene preguntas, comuníquese con el fabricante a la dirección o al número telefónico que se incluyen en la garantía. 2.
PAGE 10
MODELOS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Página 10 INSTALACIONES TÍPICAS Montaje de la cubierta en viguetas “I”. Montaje de la cubierta en cualquier parte entre las viguetas “I” por medio de barras de suspensión. Montaje de la cubierta en cualquier parte entre armaduras por medio de barras de suspensión. PLANIFICACIÓN DE LA INSTALACIÓN ÁREA QUE COCINA No instale sobre o dentro de esta área. 45o Montaje de cubierta en viguetas. NO PARA EL USO EN UN ÁREA QUE COCINA.
PAGE 11
MODELOS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Página 11 INSTALE LA CUBIERTA Y EL CONDUCTO 1a. Instale la cubierta en las viguetas o viguetas “I”. ORIFICIO PARA MONTAJE CON TORNILLO OPCIONAL (4) Con un alicate, doble las LENGÜETAS de la cubierta a 90°. LENGÜETA Sostenga la cubierta en su lugar de manera que las lengüetas de la cubierta hagan contacto con la parte SEPARADOR (se usa para inferior de la vigueta.
PAGE 12
MODELOS QTXE080 • QTXEN080 • QTXE090C • QTXE110 • QTXEN110 • QTXE1102 Página 12 CONEXIÓN ELÉCTRICA INSTALE LA REJILLA 5. Termine el cielo raso. Instale el material del cielo raso. Recorte alrededor de la cubierta. 6. Acople la rejilla a la cubierta. Apriete los resortes de la rejilla e insértelos en las ranuras que se encuentran a cada lado de la cubierta. 4. Conecte los cables eléctricos. Extienda el cableado de la casa de 120 V CA al lugar de la instalación.