Configuration Guide User guide

1542 FastIron Configuration Guide
53-1002494-02
PIM Sparse
RP 1 configuration
The following commands provide the configuration for the RP 1 router in Figure 175.
Brocade RP1(config)#router ospf
Brocade RP1(config-ospf-router)# area 0
Brocade RP1(config-ospf-router)# exit
Brocade RP1(config)# interface loopback 1
Brocade RP1(config-lbif-1)# ip ospf area 0
Brocade RP1(config-lbif-1)# ip ospf passive
Brocade RP1(config-lbif-1)# ip address 10.0.0.1/32
Brocade RP1(config-lbif-1)# ip pim-sparse
Brocade RP1(config-lbif-1)# exit
Brocade RP1(config)# interface loopback 2
Brocade RP1(config-lbif-2)# ip ospf area 0
Brocade RP1(config-lbif-2)# ip ospf passive
Brocade RP1(config-lbif-2)# ip address 10.1.1.1/32
Brocade RP1(config-lbif-2)# exit
Brocade RP1(config)# interface ethernet 5/1
Brocade RP1(config-if-e1000-5/1)# ip ospf area 0
Brocade RP1(config-if-e1000-5/1)# ip address 192.1.1.1/24
Brocade RP1(config-if-e1000-5/1)# ip pim-sparse
Brocade RP1(config)# interface ethernet 5/2
Brocade RP1(config-if-e1000-5/2)# ip ospf area 0
Brocade RP1(config-if-e1000-5/2)# ip ospf cost 5
Brocade RP1(config-if-e1000-5/2)# ip address 192.2.1.1/24
Brocade RP1(config-if-e1000-5/2)# ip pim-sparse
Brocade RP1(config)# interface ethernet 5/3
Brocade RP1(config-if-e1000-5/3)# ip ospf area 0
Brocade RP1(config-if-e1000-5/3)# ip ospf cost 10
Brocade RP1(config-if-e1000-5/3)# ip address 192.3.1.1/24
Brocade RP1(config-if-e1000-5/3)# ip pim-sparse
Brocade RP1(config-if-e1000-5/3)# exit
Brocade RP1(config)# router pim
Brocade RP1(config-pim-router)# rp-candidate loopback 1
Brocade RP1(config-pim-router)# exit
Brocade RP1(config)# router msdp
Brocade RP1(config-msdp-router)# msdp-peer 10.1.1.2 connect-source loopback 2
Brocade RP1(config-msdp-router)# originator-id loopback 2
RP 2 configuration
The following commands provide the configuration for the RP 2 router in Figure 175.
Brocade RP2(config)#router ospf
Brocade RP2(config-ospf-router)# area 0
Brocade RP2(config-ospf-router)# exit
Brocade RP2(config)# interface loopback 1
Brocade RP2(config-lbif-1)# ip ospf area 0
Brocade RP2(config-lbif-1)# ip ospf passive
Brocade RP2(config-lbif-1)# ip address 10.0.0.1/32
Brocade RP2(config-lbif-1)# ip pim-sparse
Brocade RP2(config-lbif-1)# exit
Brocade RP2(config)# interface loopback 2
Brocade RP2(config-lbif-2)# ip ospf area 0
Brocade RP2(config-lbif-2)# ip ospf passive
Brocade RP2(config-lbif-2)# ip address 10.1.1.2/32
Brocade RP2(config-lbif-2)# exit
Brocade RP2(config)# interface ethernet 5/1
Brocade RP2(config-if-e1000-5/1)# ip ospf area 0
Brocade RP2(config-if-e1000-5/1)# ip address 192.1.1.2/24