User Manual

602 Unified IP MIB Reference
53-1003106-01
MPLS LSP table
60
mplsPathType
brcdIp.1.2.15.1.2.3.1.14
Syntax: Integer
Read-only The type of path that is active. This field is meaningless
unless mplsPathName contains no value. Paths can be
the following types:
• other(1)
• primary(2)
• standby(3)
• secondary(4)
mplsLspAdaptive
brcdIp.1.2.15.1.2.3.1.15
Syntax: TruthVal
Read-only Indicates if this LSP supports the Adaptive mechanism.
mplsLspBfdSessionId
brcdIp.1.2.15.1.2.3.1.16
Syntax: Unsigned32
Read-only The BFD session associated to this LSP:
• Zero indicates that no BFD session exists for this LSP.
• Non-zero is an index to an entry in bfdSessTable.
mplsLspReoptimizeTimer
brcdIp.1.2.15.1.2.3.1.17
Syntax: Unsigned32
Read-only The number of seconds from the beginning of one
reoptimization attempt to the beginning of the next
attempt.
mplsLspCoS
brcdIp.1.2.15.1.2.3.1.18
Syntax: ClassOfService
Read-only The Class of Service.
mplsLspHopLimit
brcdIp.1.2.15.1.2.3.1.19
Syntax: Unsigned32
Read-only The number of hops this LSP can traverse.
mplsLspCspf
brcdIp.1.2.15.1.2.3.1.20
Syntax: Integer
Read-only Indicates if the CSPF path calculation is enabled on this
LSP.
mplsLspCspfTieBreaker
brcdIp.1.2.15.1.2.3.1.21
Syntax: Integer
Read-only The tie-breaker to use for selecting the CSPF equal-cost
paths. This field is not applicable if mplsLspCspf is
disabled.
mplsLspFrrMode
brcdIp.1.2.15.1.2.3.1.22
Syntax: Integer
Read-only Indicates which protection method is to be used for MPLS
Fast Reroute:
• “detour” for one-to-one backup
• “facility” for facility backup
mplsLspFrrSetupPriority
brcdIp.1.2.15.1.2.3.1.23
Syntax: Unsigned32
Read-only The setup priority for the MPLS Fast Reroute.
The value of this variable is not applicable if
mplsLspFrrMode is “none”.
mplsLspFrrHoldingPriority
brcdIp.1.2.15.1.2.3.1.24
Syntax: Unsigned32
Read-only The hold priority for the MPLS Fast Reroute.
The value of this variable is not applicable if
mplsLspFrrMode is “none”.
mplsLspFrrHopLimit
brcdIp.1.2.15.1.2.3.1.25
Syntax: Unsigned32
Read-only The hop limit for the MPLS Fast Reroute.
The value of this variable is not applicable if
mplsLspFrrMode is “none”.
mplsLspFrrBandwidth
brcdIp.1.2.15.1.2.3.1.26
Syntax: Unsigned32
Read-only The bandwidth constraint for the MPLS Fast Reroute. The
value zero indicates that the detour route uses a best-
effort value for bandwidth.
The value of this variable is not applicable if
mplsLspFrrMode is “none”.
Name, OID, and syntax Access Description