O W N E R ’S MA N UA L S1000-EW S1000-RB S1000-RW S900-EW S1000-EB S900-RW
This manual contains important safety information. Before operating the unit, please read this manual thoroughly, and retain it for future reference.
PRODUCT FEATURES Swash 900 and Swash 1000 Models: Ergonomic heated seat – with four temperature settings (High/Med/Low/Off). Instant and endless warm water – the cutting-edge instant ceramic heating system ensures an endless warm water stream for posterior and feminine washes while reducing power consumption by up to 60% over conventional storage tank systems. Dual stainless steel nozzles – separate stainless steel nozzles resist soiling and bacterial contamination for enhanced hygiene.
SAFETY PRECAUTIONS Danger: If not observed, serious injury or even death may occur as a result of electrocution. Warning: If these warnings are not observed, considerable physical injury or property damage may occur as a result of burns, electrocution or fire. Caution: If these cautions are not observed, slight physical or property damage may occur. READ ALL INSTRUCTIONS BEFORE USING. Save these instructions for future reference.
SAFETY PRECAUTIONS • If foreign material enters the product, pull the power plug out of the electrical outlet, turn off the main water valve, and call the Brondell Service Center. • Do not disassemble, repair, or modify the product yourself. • Do not use the product while wet or place the product where it can fall into a tub or sink. • Do not reach for the product if it has fallen into water. Unplug the product immediately and call the Brondell Service Center.
SAFETY PRECAUTIONS • Do not open/close the seat cover using excessive force. • Exercise caution that urine does not come into contact with the nozzles or warm air dryer outlet – failure to do so may result in bad odors or malfunction. • If the product will not be used for a long period of time unplug the power cord, close the main water supply valve, and drain any water in the water tank. • Do not pull out the bidet hose or connection hose using excessive force.
PARTS & CONFIGURATION The Swash 900 and the Swash 1000 have the following dimensions: The Swash 900 and 1000: Round Size 202 mm 382 mm 411 mm (7.9 inch) 134 mm 350 mm (5.3 inch) (13.8 inch) (15 inch) (16.2 inch) The Swash 900 and 1000: Elongated Size 202 mm 382 mm 411 mm (7.9 inch) 134 mm 385 mm (5.3 inch) (15.2 inch) Bottom View (15 inch) (16.2 inch) Distance Between Mounting Holes 140 mm ~ 210 mm 140 mm ~ 210 mm (5.5 ~ 8.3 inch) (5.5 ~ 8.3 inch) 49 mm (1.
PARTS & CONFIGURATION Product Configuration 1. Lid 8. T-valve connector 2. Warning sticker 9. Power cord 3. IR sensor 10. Production sticker 4. Nozzles 11. Drain plug 5. Body (seat) sensor 12. Quick release button 6. Bidet seat 13. Mounting plate 7. Bidet hose 14.
REMOTE CONTROL Spray Spray Swash 900 Swash 1000 7
INSTALLATION Installation Parts 7. Rubber T-Valve Washer 8. T-Valve Connector 9. Bidet Hose 10. Remote Control w/ Wall Mount 11. 2 ea Remote Screw 12. 2 ea Remote Anchor 13. 3 AAA Batteries 1. 2 ea Mounting Bolt 2. 2 ea Rubber Cone Washer 3. 2 ea Flat Washer 4. 2 ea Barrel Nut 5. Mounting Plate 6.
INSTALLATION Before Installation: Check water supply line: Check the line that connects the toilet tank to the water shut off valve. If it is a rigid pipe, you may need to purchase a flexible hose to replace it before installing the Swash. The length of the hose and the size of the connectors will vary. Residual moisture is normal Every product is tested with pure water during production to ensure the highest quality and performance.
INSTALLATION a. Install the T-Valve with the rubber washer to the incoming water connection on the bottom of your toilet tank. Be sure that you place the flat edge of the rubber washer into the T-Valve against the metal with the raised lip facing the toilet tank connection. b. Connect the water supply line coming from the wall to the bottom of the T-Valve. Steps 3a & 3b 4. Connect Bidet Hose to T-Valve a. Connect one end of the bidet hose to the T-Valve and set aside. 5.
INSTALLATION 8. Connect Power a. Plug the power cord into the electrical outlet. Important: Make sure to only use a grounded GFI (ground fault interrupter) electrical outlet. In the case of a short circuit, a grounded GFI outlet may help prevent electric shock or injury. If using an extension cord is unavoidable, use one with grounding terminals for 120V~/60 Hz or higher only. Installing the Remote Control 1. Battery Installation a.
OPERATION Quick Reference Guide: Bidet Seat Auxiliary control panel Seat Display Note: Basic functions such as Rear Cleansing and Nozzle Cleaning can be used without the remote by utilizing the auxiliary buttons shown here. C B D E A A Seat Display A Remote IR Receiver C Remote IR Receiver Receives signal from remote control D Receives signal from remote control B E Auxiliary control panel 2 seconds to turn off.
OPERATION Quick Reference Guide: Remote Control A B C ‘Wide Spray’ button D Spray For the Swash 900 models the Move, Dry, Sterilize, and Deodorize functions are excluded 13
OPERATION Quick Reference Guide: Remote Control (Page 2) B A C D ‘Wide Spray’ indicator When the “Wide Spray” button is pressed, the indicator cycles through the following options: Concentrated Stream (Blue) Medium Stream (Pink) Wide Stream (Red). ‘Dry’ button Use this button to engage 3 levels of the warm air dryer. Swash 1000 models only “Move” (Nozzle Oscillation) button This button engages the oscillation function on the front or rear nozzles during a wash cycle.
OPERATION Using the Swash Important note: The wash functions and the warm air dryer function will not work unless the body sensor in the seat detects someone sitting down (skin conductivity sensor). To override the safety sensor, please refer to the section in the manual called “Configuring a Special Mode”. Important note: The remote control will not operate the Swash if the batteries are weak, dead, or not installed properly (remote requires 3 x AAA batteries to function).
OPERATION Water Flow / Water Pressure Adjustment While the cleansing function is operating, press the Water Pressure/Dry Temp “+” and “-“ buttons on the remote control to increase or decrease the water pressure of the spray. There are 3 water pressure levels: Low – Med – High. Wide Spray To adjust the spray width of the washing stream during a cleansing cycle, press the Wide Spray button.
OPERATION Warm Air Dryer Temperature – Swash 1000 Only While air dryer function is operating, press the Water Pressure/Dry Temp. button “+” and “-“ to adjust warm air dryer temperature to desired level. There are 4 levels for the warm air dryer: Low – Med – High- Off. Additional Features Deodorization – Swash 1000 Only When you sit down on the seat, the deodorizing function starts automatically on a low setting. To activate the deodorizer on a high setting, press the Deodorize button on the remote control.
OPERATION (If no buttons on the Remote control are pressed for approximately 5 seconds, the remote display lights are turned off to conserve remote battery life). Selecting/Cancelling Eco Mode 1. Press and hold down the “Power” and “Rear Cleansing” auxiliary buttons simultaneously for approximately 5 seconds until all the seat display lights start flashing. 2. Press the “Rear Cleansing” button to Set or Cancel Eco Mode. a. If Eco Mode indicator light is turned on, this indicates Eco Mode has been set. b.
SPECIFICATIONS Brondell Swash S1000-EW, S1000-RW, S1000-EB, 1000-RB, S900-EW, S900-RW 16 psi – 98 psi Round 15” (Width) x 19.4” (Depth) x 5.66” (Height) in inches Elongated 15” (Width) x 20.8” (Depth) x 5.66” (Height) in inches 13.2 lbs (round) – 14.3 lbs (elongated) of L: 88.7° – M: 94.1°– H: 99.5° in Fahrenheit 1200 L: 87.8° – M: 93.2° – H: 98.6° in Fahrenheit Remote control dimensions Remote: 2”(Width) x 5” (Length) x 1” (Depth) Remote w/holder: 2.5”(Width) x 5.5” (Length) x 1.1” (Depth 330 lbs.
MAINTENANCE Seat Cleaning and Removal Important: Unplug the Swash from the power source before cleaning or removing the seat. Use a soft, damp cloth and mild cleanser (such as dish soap, Simple Green or Windex) to wipe down the seat. DO NOT scrub or use harsh, abrasive products to clean the Swash. DO NOT use thinner, benzene, acidic chemicals, chloride, or hydrochloric acid detergent. This may result in corrosion to the metal parts or discoloration or scratches to the bidet body.
MAINTENANCE Product Storage & Use Short term non-use: If the product will not be used for more than a few weeks, you can simply unplug it. You may also consider shutting the water supply off at the wall for extra precaution. Long term non-use: If the product will not be used for an extended time (longer than 4 months), you should unplug the unit, shut the water supply off at the wall, and then drain the hot water heater.
TROUBLESHOOTING Problem The bidet seat is not working Possible Causes 1. Bidet not plugged in 1. Make sure the bidet is plugged in 2. No power to Swash 2.Check and reset GFI outlet 3. There is power, but nothing happens when trying to use the Swash 3. Check if the Remote control batteries are dead. Replace them if necessary 4. Not activating body sensor Product shuts off during use Possible Solutions 1. Washing or drying time exceeded the cycle time 2. Power failure 4.
TROUBLESHOOTING Problem Seat not heated Possible Causes 1. Seat temperature set to off 2. Resettable fuse blown Possible Solutions 1. Make sure that the Seat temperature setting is on (Low- Blue light, Med- Pink light, High- Red light, Off- No light) 2. The bimetal resettable fuse may blow if the temperature exceeds over the normal level. The bidet will not work and show an error message until the bidet cools down. The fuse will automatically reset Water (wash spray) not heated 1.
Brondell Warranty Policy Brondell products are backed by some of the most comprehensive warranties in the industry. Brondell warrants that all products (excluding consumable items) shall be free from defects in material and workmanship under normal use and service. Commercial Warranty: Warranty period 1 year from original purchase date for all Brondell products. Warranties may not apply to products that are used for heavy commercial, hospital, or other high use non-residential applications.
d) Damage or loss resulting from negligent or improper installation including installation of a unit in a harsh or hazardous environment. e) Damage or loss resulting from removal, improper repair, modification of the product, or improper maintenance including damage caused by chlorine or chlorine related products. f) Damage or loss resulting from electrical surges, electrical outages, lightning strikes or other acts which are not the fault of Brondell or which the Product is not specified to tolerate. 4.
For questions, contact Brondell Customer Service: 1-888-542-3355 CONTACT INFORMATION Brondell, Inc. PO Box 470085 San Francisco, CA 94147-0085 Phone: 1-888-542-3355 Email: support@brondell.com Web: www.brondell.com WARRANTY For detailed warranty information and product registration, please go on-line at www.brondell.com Please retain receipt records for any warranty claims.