FX-3 TWIN PMR 446 8 Channel 2-Way Radios Instruction manual SCAN mic English manual NOTE: MANUAL SIZE: L125 x W100mm
Content Contents .............................................................. 2 Introduction......................................................... 3 Controls and displays ....................................... 3 Component Guide .......................................... 4 SettingUp Your PMR Radio .............................. 5 Battery Installation ........................................... 5 Battery Meter ................................................... 6 Low Battery Indicator ..................
Introduction Included In Your Package When you unpack your PMR Radio, you should find the following items enclosed in the package: 8-channel PMR unit-2PCS Belt-Clip -2PCS This manual SCAN mic X 2pcs Controls and Displays 1. Power Button 2. Menu Button 3. Call Button 4. PTT(Talk Button) 5. Antenna 6. LCD Panel 7. Up Button (Change Channel and Volume) 8. Down Button (Change Channel and Volume) 9.
Component Guide Sca n SCAN Rx Tx Loc k Channel number Ba tte ry le ve l Volu m e 5. A nt enna 9. B elt c lip SCAN 6. LC D panel 4. P TT(Ta lk but ton) 8. D own butto n 7. U P butt on 1.Power button 3.C all b utt on 2.
Setting Up Your PMR Radio Battery Installation To use the radio, you must install 3 AAA size batteries. Caution: incorrect positioning of the batteries can damage both the batteries and the unit. To install the batteries: Remove the belt clip by pulling the tab on the top of the belt clip back, and sliding it up and off of the unit. Slide the battery door down to release the battery cover. lnsert three AAA batteries. Position the batteries according to the polarity markings on the plastic.
Battery Meter The battery meter is located in the bottom left corner of the LCD display panel on the unit. It looks like a battery with vertical bar inside. As the power is used up, the bar will disappear. Low Battery Indicator When the batteries need to be changed, the battery vertical bar inside will disappear. To ensure uninterrupted communication, replace the batteries as soon as possible. Note: Always use alkaline batteries for replacements.
Operation Turning On Your PMR Push & hold the Power button for at least 2 seconds to turn the PMR radio ON or OFF. The unit will beep, the LCD panel will display information about your radio, and the panel will be illuminated by a orange light for several seconds. SCAN mic Communication You can communicate two ways with your new PMR radio. There are 8 channels available to you, You can either talk directly to others and hear their response, or you can call or page them with an audible tone.
When you are using the unit in conversation, you must release the PTT and/or CALL buttons to hear the responses of the other people. Failure to do so will keep your unit in transmission mode, preventing you from hearing other units. Respond Prompt Tone When the person talking to you from another radio finishes speaking and releases his PTT button, you will hear a tone from your unit. This means that the other radio is now in receive mode, and you can begin your transmission.
Press the MENU (Channel Set) button. The icon "“1 "”on the display panel will begin to flash. While the number is flashing, press the up or down arrow buttons until you reach the desired channel. Press the MENU (Channel Set) button again to set the channel. If you do not press MENU the second time, The unit will automatically return to normal operation in ten seconds. To speak to Another Radio Turn the volume up to an audible level. • • Press and hold the PTT button on the left side of the unit.
the time of your conversation. Some conditions that affect range are: Buildings Dense trees or foliage Hilly or mountainous terrain The best range will be in flat, open terrain, without obstructions. Using the function (monitor) to override the automatic squelch will help extend the range to the maximum limits. Your range is also dependent on the battery condition of the radio, the type of terrain where you are located, and the strength of the signal from the transmitting radio.
Channel Lock This feature locks the channel adjustment buttons on the front to the unit so that the channel cannot be changed accidentally. SCAN To Lock the channel: Press and hold the MENU button until " " appears on the display. “ mic To Unlock the channel: Press and hold the MENU button until " " disappears from the display. Channel Scan Your radio can scan across it’ s 8 channels for any activity. This allows you find other radios without having to change channels.
Monitoring the current channel Normally PMR will not pick up very weak signals. But you can monitor the current channel for all sounds. TO activate the monitoring feature Press the MENU and UP button at the same time. Your handset will pick up any signals on the current channel, including pick up any signals on the current channel. Including background noise. Press MENU button to stop monitoring Automatic Battery Save Your PMR unit has special circuitry designed to extend the life of your battery.
Frequencies Channel PMR Channel Frequencies Channel 1 2 3 4 Frequency (MHz) Channel 446.00625 446.01875 446.03125 446.04375 5 6 7 8 13 Frequency (MHz) 446.05625 446.06875 446.08125 446.
WWW.brondi.it Brondi Telefonia S.P.A info@brondi.
