TM SIMP HOME ® LIFE BY DESIG N TM ARTISAN / HOLDEN / STRATFORD SIDEBOARD BUFFET MODEL # AXCART11-HB 1/24
TM SIMP HOME ® LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION PART DESCRIPTION A Fron MODEL # AXCART11-HB B C t/A van t Fron t/A TOP QTY 1 van t BOTTOM SHELF QTY 1 DL DR t Fron EL ant t/A Fron LEFT SIDE QTY 1 ER van t t/A LEFT DIVIDER QTY 1 RIGHT SIDE QTY 1 F Fron t van t/A Fron / Av SHELF QTY 2 GL van t RIGHT DIVIDER QTY 1 DOOR (L&R Same) QTY 2 LEFT BACK PANEL QTY 1 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION PART DESCRIPTION GR Warning Label IL H G RIGHT BACK PANEL QTY 1 DRAWER FRONT QTY 6 MIDDLE BACK PANEL QTY 1 IR LEFT DRAWER SIDE QTY 6 K MODEL # AXCART11-HB J RIGHT DRAWER SIDE QTY 6 DRAWER BACK QTY 6 L DRAWER BOTTOM QTY 6 BOTTOM SUPPORT LEG QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION HARDWARE DESCRIPTION 1 2 ALLEN KEY BOLT M6 X 30mm QTY 12 5 CAM LOCK PIN CAM LOCK QTY 24 SETS 7 PHILLIPS SCREW ROUND HEAD M4 X 15mm QTY 28 ALLEN KEY QTY 1 4 3 ALLEN KEY SCREW M6 X 30mm QTY 36 6 9 MODEL # AXCART11-HB 8 SHELF SUPPORT QTY 12 MAGNET AND PLATE QTY 2 SET 11 10 HANDLE M4 X 30 mm QTY 8 SETS 12 aM . 4X25mm-QTY2 (1siextra) bM . 4X15mm-QTY1 M c.
COMPONENTS-KEY DIAGRAM MODEL # AXCART11-HB A Fron t / Av ant GL G GR DR ER EL C DL C Fron Fron t F Fron t / Av Fron t / Av / Ava nt t / Av ant F ant ant Fron t / Av ant B L J L IR IL H K 8/24
ASSEMBLY MODEL # AXCART11-HB P STEP-1 X H 3 H 1. Attach 4 Cam Lock Pins 3 to pre-drilled holes at back of Drawer Front H . 2. Use Phillips screwdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCART11-HB STEP-2 IR IL H 3 H IR IL 1. Align Cam Lock Pins with guide holes and attach Drawer Sides IL , IR . 2. Insert 2 Cam Locks 3 into guide holes on each Drawer Side IL , IR . 3. Use Phillips screwdriver to secure Cam Locks.
ASSEMBLY MODEL # AXCART11-HB STEP-3 K IR IL H 1. Slide Drawer Bottom K firmly into slots on Drawer Sides IL , IR and Drawer Front H . STEP-4 J IR 2 K 5 IL H 1. Align Drawer Back J with Drawer Bottom K and press firmly into slot . 2. Attach Drawer Back using 2 Allen Key Screws 2 through guide holes on each Side IL , IR . 3. Use Allen Key 5 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCART11-HB STEP-5 NOTE: The screwdriver is not included in the hardware pack. H 4 1. Use Phillips screwdriver to attach Handle 4 to Drawer Front H . Repeat Step 1-5 for the other five drawers.
ASSEMBLY MODEL # AXCART11-HB STEP-6 Front / Avant EL Front / Avant Front / Avant ER B 2 5 1. Attach Dividers EL , ER to Bottom Shelf B using 6 Allen Key Screws 2 (3 Screws / each Divider ). 2. Use Allen Key 5 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCART11-HB Front / Avant STEP-7 Front / Avant Front / Avant EL DL DR Front / Avant ER Front / Avant B 1 5 1. Attach Bottom Shelf B to Sides DL , DR using 6 Allen Key Bolts 1 ( 3 Bolts / each Side ). 2. Use Allen Key 5 to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCART11-HB STEP-8 2 1 5 5 Front / Avant Front / Avant Front / Avant A Front / Avant Front / Avant EL ER B Front / Avant DL DR 1. Attach Top A to Sides DL , DR using 6 Allen Key Bolts 1 ( 3 Bolts / each Side ). 2. Attach Top A to Dividers EL , ER using 6 Allen Key Screws 2 ( 3 Screws / each Divider ). 3. Use Allen Key 5 to tighten screws and bolts. Do not over-tighten.
ASSEMBLY MODEL # AXCART11-HB STEP-9 Front / Avant Front / Avant A DL Front / Avant Front / Avant EL Front / Avant ER DR B B B 11 1. Attach two Bottom Support Leg L to Bottom Shelf B using 8 Phillips Screws 11 . 2. Use Phillips screwdriver to tighten screws. Do not over-tighten.
ASSEMBLY MODEL # AXCART11-HB STEP-10 NOTE: The screwdriver is not included in the hardware pack. Note: Thebackofthecabinetframedoesnothave pre-driledholestoattachthebackpanels. Warning Label Fron A t/A van t GR G Fron t/A van t GL 6 1. Attach the Back Panels GL , GR , G to back frame of cabinet using Phillips Screws Round Head 6 through guide holes from panel. 2. Use Phillips screwdriver to tighten screws.
ASSEMBLY MODEL # AXCART11-HB STEP-11 A Fron t/A van t DR F Fron t ER Fron t/A EL van t Fron Fron t/A Fron t/A ant B t/A DL / Av van t van t van t First Step F 9 Last Step (After adjust the door) 9 1.AttachhingesonDoorsFtoSidesDL,DRusingPhilpsScrews9intopre-drilholes: - UsingPhilpsscrewdrivertoattachScrews9atmiddleholeofhingesfor bothtop&bottomhinges. -Adjustthedoortoensuretheyarealignedstraight&squarewithbottomshelf&side.
ASSEMBLY MODEL # AXCART11-HB STEP-12 NOTE: The screwdriver is not included in the hardware pack. F A Fron t/A van t DR Fron t ER Fron t/A EL van t Fron B t/A DL / Av ant van t Fron t/A van t Fron t/A van t 7 F 10 4 10 7 1. Attach Magnet Plates 7 to bottom corner of Doors F using Phillips Screws 10 into pre-drilled holes on Doors F . 2. Attach Magnet 7 using Phillips Screws 10 into pre-drilled holes on Bottom Shelf B . 3. Use a Phillips screwdriver to attach Handles 4 to Doors F .
ASSEMBLY MODEL # AXCART11-HB STEP-13 shelf level 1 shelf support anti - tipping 8 shelf level 2 shelf level 3 C 8 C 1.Use4ShelfSupports8foreachCabinetShelfCindesiredlocation. 2.2ShelfSupports8maybeusedonbacktopofeachCabinetShelfCasa tippingrestraint .
ASSEMBLY MODEL # AXCART11-HB STEP-14 1. Insert assembled drawers into glides on assembled sideboard.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-15 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. P Drill a 3/16 inch hole in the wall.
TM SIMP HOME ® LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.