TM SIMP HOME ® LIFE BY DESIG N TM DRAPER / BAXTER / TIERNEY 4 DRAWER FLOOR CABINET MODEL # AXCBCDRP-02 1/20
TM SIMP HOME ® LIFE BY DESIG N TM Questions, problems, assembly help, missing parts? No need to return the product, we will gladly help and ship your replacement parts free of charge Please call Customer Service at 1-866-518-0120 ext. 262 Monday to Friday between 9 am –4 pm EST or go to www.simpli-home.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. SAFETY INFORMATION CAUTION: Injuries and damage can occur from furniture tip over if product is not properly anchored to the wall. Use the Furniture Anti-Tipping Restraint provided with the product. Consult our assembly instructions for help.
IMPORTANT : Please read this manual carefully before beginning assembly of this product. Keep this manual for future reference. CARE and MAINTENANCE Perhaps the greatest environmental damage to wood furniture comes from wide swings in relative humidity (RH) in our homes. Wood absorbs and desorbs water as relative humidity rises and falls, and in doing so it swells and shrinks. Making matters worse, it expands and contracts unequally along different grain directions.
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION A MODEL # AXCBCDRP-02 . . BL BR Front Fron Front t / Avan vant . LEFT SIDE QTY 1 . C RIGHT SIDE QTY 1 . D F t t/A TOP QTY 1 t ron / Avan E t van /A BOTTOM SHELF QTY 1 . CROSS BAR QTY 3 . F . GL DRAWER FRONT QTY 4 CROSS BAR QTY 1 GR LEFT DRAWER SIDE QTY 4 RIGHT DRAWER SIDE QTY 4 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION . PART DESCRIPTION H . . I J DRAWER BOTTOM QTY 4 DRAWER BACK QTY 4 . . K TOP BACK PANEL QTY 1 . L1 BOTTOM BACK PANEL QTY 1 MODEL # AXCBCDRP-02 L2 LEG (L&R Same) QTY 2 LEG (L&R Same) QTY 2 NEED HELP? For help with assembly or if you are missing a part, Please call customer service at 1-866-518-0120 ext.
PRE-ASSEMBLY INFORMATION . HARDWARE DESCRIPTION 1 2 . CAM LOCK PIN CAM LOCK QTY 26 SETS . MODEL # AXCBCDRP-02 . 3 WOOD DOWEL Ø8 X 30mm QTY 14 . 4 PHILLIPS SCREW M4 X 15mm QTY 4 . 5 ALLENKEYBOLTM : 6X50mmQ - TY8 PHILLIPS SCREW ROUND HEAD LOCKWASHERØ: 10/Ø6X15.mmQ - TY8 M4 X 15mm WASHERØ : 16/Ø6X1mmQ - TY8 QTY 3 QTY 8 SETS PHILLIPS SCREW M4 X 30mm QTY 16 . 6 . 7 . 8 9 aM . 4X25mm-QTY2 (1siextra) bM . 4X15mm-QTY1 cM .
COMPONENTS-KEY DIAGRAM MODEL # AXCBCDRP-02 Ava Front / Front / A nt J Avant D Front / E Avant D D K BL BR vant A Front / L1 C L2 L1 L2 GL H I F GR 8/20
ASSEMBLY MODEL # AXCBCDRP-02 P STEP-1 X 1 1 1 F 1. Attach four Cam Lock Pins 1 into pre-drilled holes on Drawer Front F . 2. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten. STEP-2 GL GR GL GR GR GR 1 1.AlignCamLockPinswithguideholesandattachDrawerSides 2.InserttwoCamLocks1intoguideholesoneachDrawerSide 3.UsePhilpsscrewdrivertosecureCamLocks.Donotover-tighten. GL,GRtoDrawerFrontF. GL,GR.
ASSEMBLY MODEL # AXCBCDRP-02 STEP-3 4 H I GL GR GL GR F I F 1.SlideDrawerBottomIfirmlyintoslotsonDrawerSidesGL,GRandDrawerFrontF. 2.AlignDrawerBackHwithDrawerBottomIandpressfirmlyintoslot. 3.AttachDrawerBackusingtwoPhilpScrews4throughguideholeson eachDrawerSide GL,GR.Use Phillips screwdrivertotightenScrews. STEP-4 1. Repeat Step 1-3 for the other drawers.
ASSEMBLY MODEL # AXCBCDRP-02 STEP-5 7 6 L2 L1 L1 C L2 1. Attach Legs L1, L2 to Bottom C . 2. Use eight Allen Key Bolts 6 , eight Lock Washers 6 and eight Washers 6 to secure part C and L1 , L2 . 3. Use Allen Key 7 to tighten Bolts. Do not over-tighten P STEP-6 1 X 1 C nt / Fro nt Ava 1 1. Attach Cam Lock Pins 1 into pre-drilled holes on part C . 2. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten.
ASSEMBLY MODEL # AXCBCDRP-02 P STEP-7 X 1 1 1 Fron t / Av ant A 1 BL BR 1. Attach Cam Lock Pins 1 into pre-drilled holes on each part A , BL , BR . 2. Use Phillips screwdriver to secure Cam Lock Pins. Do not over-tighten. 2 2 3. Insert Wood Dowels 2 into guide holes on each part D , E . 4. Use rubber mallet to tap Dowels 2 into bottom of holes securely. 1/2 length of Dowels should be exposed.
ASSEMBLY MODEL # AXCBCDRP-02 STEP-8 D D D E BL Front / Avant D 1 D D E 1 BL 1. Align Wood Dowels and Cam Lock Pin with guide holes and attach parts D , E to Left Side BL . 2. Insert one Cam Lock 1 into guide hole on part E . 3. Use Phillips screwdriver to secure Cam Lock.
ASSEMBLY MODEL # AXCBCDRP-02 STEP-9 D E Front / Avant Front / Avant D BR BL D 1 D Front / Avant E BL Front / Avant D 1 BR D 1. Repeat Step-8 for the Right Side BR .
ASSEMBLY MODEL # AXCBCDRP-02 STEP-10 tnavA rF / tno tnavA rF / tno BL BR tnavA rF / tno C tnavA rF / tno tnavA rF / tno BL BR 1 tnavA rF / tno C 1. Align Cam Lock Pins with guide holes and attach parts BL , BR to Bottom Shelf C . 2. Insert two Cam Locks 1 into guide hole on each part BL ,BR . 3. Use Phillips screwdriver to secure Cam Lock.
ASSEMBLY MODEL # AXCBCDRP-02 Warning Label STEP-11 J / tnorF K tnavA BL BR / tnorF 1.SlideBackPanelsJ,Kfirmlyinto slotsonSidesBL,BRandBottomShelfC. tnavA C 1 tnavA A rF / tno A tnavA rF / tno tnavA rF / tno BL BL BR BR tnavA rF / tno 2. Align Cam Lock Pins with guide holes and attach parts BL , BR to Top A . 3. Insert two Cam Locks 1 into guide hole on each part BL ,BR . 4. Use Phillips screwdriver to secure Cam Lock.
ASSEMBLY MODEL # AXCBCDRP-02 Note: Thebackofthecabinetframedoesnothave pre-driledholestoattachthebackpanels. STEP-12 /oFrnt /oFrnt A natv A natv J 5 BR K BL 3 C 8 1. Attach the Back Panels J , K to back frame using Phillips Screws Round Head 5 through guide holes from Back Panels. 2. Attach the Corners Support 8 to back frame using Phillips Screws 3 through guide holes from Corners Support 8 . 3. Use Phillips Screwdriver to tighten screws. Do not over-tighten. STEP-13 1.
FURNITURE TIP OVER RESTRAINT ASSEMBLY WARNING Serious or fatal crushing injuries can occur from furniture tip-over. If the furniture tip over restraint kit is not in the box, please contact our customer service department in order to obtain another kit before using the furniture. STEP-14 NOTE: The screwdriver is not included in the hardware pack.
FURNITURE TIP OVER RESTRAINT ASSEMBLY Furniture Tip Over Restraint Instructions: 1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the shorter screw. x P 2. Determine where furniture is to be placed and mark location on the wall for mounting bracket screw hole approximately 2 inches below the bracket mounted to the furniture. x 3. 4. 5. 6. 7. P Drill a 3/16 inch hole in the wall.
TM SIMP HOME ® LIFE BY DESIG N TM WARRANTY Thank you for purchasing a Simpli Home – Wyndenhall – Brooklyn + Max product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights. In case of any malfunction of your product (failure, missing parts, etc.) please contact us at our toll free service line at 1-866-518-0120 ext.