User's Manual
Table Of Contents
- Product Manual RFID Reader UF80
- 1 Identification
- 2 Declaration of Conformity
- 3 General Instructions
- 4 Safety Instructions
- 5 Product Specifications
- 6 Installation
- 7 Operation
- 7.1 Operating personnel
- 7.2 Communication protocol ASC-I1
- 7.2.1 Structure of the communication protocol
- 7.2.2 Package contents
- 7.2.3 Commands of protocol
- URY - Read data range (defined EPC code)
- M - Scan EPCs
- W - Write EPC code
- UWZ - Write data range of all EPC transponders (defined EPC code)
- ULZ - Locking all EPC transponders (defined EPC code)
- F - Query parameters
- P - Set parameter
- N - Reset
- O - Set output
- E - Error message
- H - Heartbeat
- V - Query software version
- K - Polling
- UFD - Query DHCP Enabled
- UPD - Set DHCP Enabled
- UFI - Query network settings
- UPI - Set network settings
- UFN - Query host name
- UPN - Set host name
- 7.2.4 Parameter
- Parameter 4 (0x04)
- Parameter 6 (0x06)
- Parameter 11 (0x0B)
- Parameter 12 (0x0C)
- Parameter 16 (0x10)
- Parameter 39 (0x27)
- Parameter 43 (0x2B)
- Parameter 47 (0x2F)
- Parameter 48 (0x30)
- Parameter 50 (0x32)
- Parameter 64 (0x40)
- Parameter 65 (0x41)
- Parameter 66 (0x42)
- Parameter 98 (0x62)
- Parameter 99 (0x63)
- Parameter 118 (0x76)
- Parameter 123 (0x7B)
- Parameter 158 (0x9E)
- Parameter 162 (0x02)
- Parameter 163 (0x00)
- Parameter 176 (0xB0)
- 7.3 Additional information
- 8 Service and Troubleshooting
- 9 Dismantling and Storage
- 10 Transport and Disposal
- 11 Accessories
- Index
Product Manual - RFID Reader UF80 65
Chapter 7
Operation
Parameter 4
(0x04)
Delay time
If a confirmation is not sent by the host, the device waits this time span before it
sends the message to the host again. The number of repetitions is defined in
parameter 6 (MaxRepeat).
0x0A - 0xFA (0.1 s) 1 - 25 s
Default: 0x32
Parameter 6
(0x06)
MaxRepeat
If a confirmation is not sent by the host, the device repeats the message
according to the set value. Only then is an error message sent.
0x00 - 0x1F
Default: 0x03
Parameter 11
(0x0B)
Reader ID
This parameter defines the address of the device in the ASC-I1 protocol. We
recommend keeping the default setting since the module can be identified via the
hardware interface.
0x00 - 0x0E
Default: 0x00
Parameter 12
(0x0C)
Acknowledgment error message
This parameter defines whether an error message must be confirmed or not.
0x00 - no confirmation is expected
0x01 - a confirmation is expected
Default: 0x01
Parameter 16
(0x10)
Attenuation of transmission output
This parameter defines the attenuation of the transmission output in dBm.
Attenuation 0x00 -> 26.5 dBm = approx. 450 mW
Attenuation 0x0A -> 26.5 dBm - 10 dBm = approx. 50 mW
Attenuation 0x13 -> 26.5 dBm - 19 dBm = approx. 4 mW
Default: 0x13