User's Manual
Table Of Contents
- Product Manual RFID Reader UF80
- 1 Identification
- 2 Declaration of Conformity
- 3 General Instructions
- 4 Safety Instructions
- 5 Product Specifications
- 6 Installation
- 7 Operation
- 7.1 Operating personnel
- 7.2 Communication protocol ASC-I1
- 7.2.1 Structure of the communication protocol
- 7.2.2 Package contents
- 7.2.3 Commands of protocol
- URY - Read data range (defined EPC code)
- M - Scan EPCs
- W - Write EPC code
- UWZ - Write data range of all EPC transponders (defined EPC code)
- ULZ - Locking all EPC transponders (defined EPC code)
- F - Query parameters
- P - Set parameter
- N - Reset
- O - Set output
- E - Error message
- H - Heartbeat
- V - Query software version
- K - Polling
- UFD - Query DHCP Enabled
- UPD - Set DHCP Enabled
- UFI - Query network settings
- UPI - Set network settings
- UFN - Query host name
- UPN - Set host name
- 7.2.4 Parameter
- Parameter 4 (0x04)
- Parameter 6 (0x06)
- Parameter 11 (0x0B)
- Parameter 12 (0x0C)
- Parameter 16 (0x10)
- Parameter 39 (0x27)
- Parameter 43 (0x2B)
- Parameter 47 (0x2F)
- Parameter 48 (0x30)
- Parameter 50 (0x32)
- Parameter 64 (0x40)
- Parameter 65 (0x41)
- Parameter 66 (0x42)
- Parameter 98 (0x62)
- Parameter 99 (0x63)
- Parameter 118 (0x76)
- Parameter 123 (0x7B)
- Parameter 158 (0x9E)
- Parameter 162 (0x02)
- Parameter 163 (0x00)
- Parameter 176 (0xB0)
- 7.3 Additional information
- 8 Service and Troubleshooting
- 9 Dismantling and Storage
- 10 Transport and Disposal
- 11 Accessories
- Index
Product Manual - RFID Reader UF80 66
Chapter 7
Operation
Parameter 39
(0x27)
Polling frequency
When polling, the reader scans the set transponder type. All detected
transponders are read out via the set communication port (see K command). If
the parameter is set to zero, there is no polling.
0x00 - 0xFF (5 ms steps)
Default: 0x00
Parameter 43
(0x2B)
Polling fallout
This number indicates the number of times a transponder is not read in
succession when polling before it is considered "not detected". Only transponders
that are not detected are reported to the host during another read operation that
is successful.
0x00 - 0xFF
Default: 0x03
Parameter 47
(0x2F)
Polling mode
Bit 0 (0x01) If this bit is set, the buzzer is turned on after a successful
read operation.
Bit 1 (0x02) not used
Bit 2 (0x04) not used
Bit 3 (0x08) not used
Bit 4 (0x10) If the inventory has been successful, the EPC is read out.
Bit 5 (0x20) not used
Bit 6 (0x40) not used
Bit 7 (0x80) not used
Default: 0x11
Parameter 48
(0x30)
Buzzer delay
This parameter defines the minimum amount of time the buzzer remains on.
0x00 - 0xFF (factor 50 ms)
Default: 0x32
Parameter 50
(0x32)
Buzzer volume
0x00 ... off
0x01 ... volume 1
0x02 ... volume 2
0x03 ... volume 3
Default: 0x01